Broseley Inset Ignite 6 Remote Handbuch

Installation & Operating Instructions

PLEASE NOTE THAT THIS APPLIANCE USES A MOTOR TO OPERATE THE

FLAME EFFECT AND THAT IT MAY BE POSSIBLE TO HEAR IT WHERE THE

BACKGROUND NOISE IS VERY LOW. THIS IS NORMAL AND SHOULD NOT

BE A CAUSE OF CONCERN.

These instructions should be read carefully and retained for future reference

Models Covered Page 2

Important Safety Advice Page 3

Technical Speciation Page 6

Assembly – York Midi and Serrano Free-Standing Page 6

Flame Effect Unit – Position within stove body Page 8

Assembly – Desire, Ignite & Hereford Free-Standing Page 8

Assembly – Inset Desire, Ignite & Hereford Page 9

Assembly – Desire, Ignite and Hereford Inset Page 11

Operating Your Stove Page 14

Maintenance Page 22

Guarantee Page 23

Contents

Models Covered

This instruction manual covers the following models:

Please see the relevant pages in the Assembly section for specic information on

how to assemble your electric stove:

Inset Ignite 6/Desire6 Remote Inset Ignite 6/Desire6 Manual

Inset Hereford 5 Remote Inset Hereford 5 Manual

Ignite 5/Desire5 Freestanding Remote Ignite 5/Desire 5 Freestanding Manual

Ignite 6/Desire 6 Freestanding Remote Ignite 6/Desire6 Freestanding Manual

Ignite 7/Desire7 Freestanding Remote Ignite 7/Desire7 Freestanding Manual

Hereford 5 Freestanding Remote Hereford 5 Freestanding Manual

Hereford 7 Freestanding Remote Hereford 7 Freestanding Manual

York Midi Freestanding Remote York Midi Freestanding Manual

Serrano Freestanding Remote Serrano Freestanding Manual

Important Safety Advice

Warning: this appliance must be earthed.

The wires in the main lead to this appliance

are coloured in accordance with the following

code:

GREEN and YELLOW Earth

BLUE Neutral

BROWN Live

As the colours of the wires in the mains lead

of this appliance may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows:

The wire, which is coloured green and yellow, must be connected to the terminal

in the plug with the letter E or by the earth symbol or coloured green or green

and yellow.

The wire, which is coloured blue, must be connected to the terminal, which is

marked with the letter N or coloured black.

The wire, which is coloured brown, must be connected to the terminal,

which is marked with the letter L or coloured red.

Important Safety Advice

WARNING:

In order to avoid overheating do not cover the heater.

In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this

appliance must not be supplied through an external switching device, such as a

timer, or connected to circuit that is regularly switched on and off by utility.

If the supply cord is damaged, it must be replaced by the manufacturer, its ser-

vice agent or a similarly qualied person in order to avoid a hazard.

Use the heater in a well-ventilated area. Do not insert or allow objects to enter any

ventilation or exhaust opening. To prevent a possible re, do not block air intakes

or exhaust openings in any manner. Do not use on soft surfaces, like a bed,

where openings may become blocked.

Do not place this heater near ammable materials, surfaces or substances, as

there may be a risk of re. Keep the above ammable materials, surfaces or

substances at least 1m from the front of the product and keep them away from the

sides and rear.

• Thisheatermustnotbelocatedimmediatelybelowaxedsocketoutlet

orconnectionbox.

• DO NOT COVER this heater, or obstruct the air inlet or

outlet, otherwise there is a risk of overheating.

• During normal operation this appliance will emit

noise from the internal fan unit.

• This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without

supervision.

• Children of less than 3 years should be kept away unless continuously

supervised. Children aged from 3 years and less than 8 years shall only switch

on/off the appliance provided that it has been placed or installed in its intended

normal operating position and they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children aged from 3 years and less than 8 years shall not plug in,

regulate and clean the appliance or perform user maintenance.

• Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.

• Do not use the heater in the immediate surrounds of a bath, a shower, or a

swimming pool.

• The heater must be cooled down completely before any maintenance work is

carried out.

• After unpacking, please make sure that the appliance is intact, with no signs of

damage caused by transport. If in doubt, do not use the appliance and contact

the Service Centre.

• If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualied persons in order to avoid a hazard.

• If this re is supplied through an extension cable, please ensure that it is the

only appliance plugged into the extension and that the instructions for the

extension cable / reel are followed.

• Do not stand the re on the carpet – stand on a rm surface, which is free of

dust and lint.

• In the event of a fault please disconnect the re from the mains supply.

TECHNICAL SPECIFICATION

Supply Voltage: AC220V-240V 50Hz

Maximum power consumption: 2KW

Heat output:

Nominal heat output (Pnom): 2KW

Minimum heat output (indicative) (Pmin): 1KW

Maximum continuous heat output (Pmax): 2KW

Auxiliary Electricity Consumption:

At nominal heat output (elmax): 12.5W

At minimum heat output (elmin): 12W

In standby mode (elSB): 0.36W

Two or more manual stages, no room temperature control no

With mechanic thermostat room temperature control no

With electronic room temperature control yes

Electronic room temperature control plus day timer yes

Electronic room temperature control plus week timer yes

Type of heat output / room temperature control

Room temperature control, with presence detection no

Room temperature control, with open window detection yes

With distance control option no

With adaptive start control yes

With working time limitation no

With black bulb sensor no

Other control options

Part List

The stove will be supplied in two separate boxes. The rst contains the cast

iron stove body and the second the ame effect unit. Check that the specied

components are included before you start setting up your Stove.

Box1

1×Cast iron stove body

(with transit bar tted)

1×Set of four legs

Box2

1×Flame effect unit

1×Decorative log set

1×Decorative coal set

1×Instruction booklet

1×Remote control

2×AAA batteries

Assembly – York Midi and Serrano Free-Standing

York Midi Freestanding Remote York Midi Freestanding Manual

Serrano Freestanding Remote Serrano Freestanding Manual

Assembly Sequence:

1. Carefully remove all packaging and protective materials from the stove body.

Remove and discard the „transit bar‟ from stove body. This item stops the

sides of the stove body from moving in transit. It has been positioned into the

vertical channels where the Flame Effect Unit is to be slotted into place.

2. Remove the cast iron lid from the stove body and lay the stove body on its

back.

3. Attach the four legs using the bolts/nuts provided. Please note these bolts/

nuts will normally be pre-tted into the base of the stove. Stand the main stove

body upright on its feet.

4. Carefully remove all packaging and protective materials from the ame effect

unit.

5. Remove the thermostat control knob from the front of the ame effect unit

(this will prevent it from being scratched whilst the ame effect unit is inserted

into the cast stove body).

6. Insert the ame effect unit into the stove body. The unit is lowered down

carefully from the top of the body with the sides located into the grooves on

each side of the stove body. If the ame effect will not slide down easily, you

may need to slacken the bolts connecting the sides of the stove body to the

front and base. Take care not to trap the cable whilst lowering the ame effect

unit into the stove body.

7. Open the main door (and ash door on York Midi). On the Serrano, the door

simply pulls open using the handle. For the York Midi you will need to turn the

handle anti-clockwise until it comes free from the locking thread.

8. Re-attach the thermostat control knob.

9. Remove the Perspex from the stove. The Perspex is held in place by four

screws which will need to be removed.

10.Remove both sides of the protective covering from the Perspex.

Flame Effect Unit – Position within stove body

Side View Top View

11. Finally place the cast iron lid back on the stove.

Assembly – York Midi and Serrano Free-Standing

The Desire, Ignite and Hereford free-standing stoves will be fully assembled,

howevertheseappliancesMUSTbesecuredtotherearwallandoorusing

thexingpointsshownbelow.

Ignite 5/Desire5 Freestanding Remote Ignite 5/Desire 5 Freestanding Manual

Ignite 6/Desire 6 Freestanding Remote Ignite 6/Desire6 Freestanding Manual

Ignite 7/Desire7 Freestanding Remote Ignite 7/Desire7 Freestanding Manual

Hereford 5 Freestanding Remote Hereford 5 Freestanding Manual

Hereford 7 Freestanding Remote Hereford 7 Freestanding Manual

The oor xing points also provide adjustment to level up the product when

placed on an un-even surface. Front Adjustment is provided by two concealed

bolts (under the base).

The wall cable will need to be passed through the hook xing on the wall. It can

then be adjusted to length and locked using the xing on the left hand side (rear

of stove body).

PleaseNotexingsarenotprovidedtosecurethestovetotheoor.

Thesexingswillvarydependingonthematerialyouarexinginto.

Assembly – Inset Desire, Ignite & Hereford

Inset Ignite 6/Desire 6 Remote Inset Ignite 6/Desire6 Manual

Inset Hereford 5 Remote Inset Hereford 5 Manual

Please unpack carefully ensuring that any loose parts and all packing items are

removed. Read any warning labels carefully (see Maintenance Section).

Place waste packaging back into box and dispose of RESPONSIBLY.

The appliance must be positioned so that plug (fused spur) is accessible.

Only when you are certain that you have completed the following

installation instructions should you plug in and switch on at the wall socket.

Contents:1xStoveBodyTrim,1offFireengine(attachedtostovebody),

Instructionleaet,4offNo.6x1¾”screws,1xDoor(Packedinbox),

2xAngleBrackets(forbackpanel),6xAngleBracketFixings,2xWall

Fixings

Check that the supply voltage details on your ame effect re are in accordance

with your electrical supply. Your re is tted with a plug incorporating a 13 Amp

fuse. In the event of replacing the fuse in the plug supplied, a 13 Amp fuse

approved by ASTA to BS 1362 must be used. Before switching on, please read

the following operation instructions.

First ensure that the opening dimensions match the drawing below

Unpack the re by removing all the boxes from

the pallet and then removing the stove main body

by loosening and removing the 4 screws. With the

body removed next unscrew the re engine from

the pallet and remove the L shaped bracket from

the bottom rear of the stove “wings”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Broseley Herd Handbücher

Broseley

Broseley Evolution 5 Multi-fuel Handbuch

Broseley

Broseley Serrano 3 Bedienungsanleitung

Broseley

Broseley Evolution 5 MK2 Handbuch

Broseley

Broseley Canterbury Bedienungsanleitung

Broseley

Broseley York Midi Bedienungsanleitung

Broseley

Broseley Canterbury Bedienungsanleitung

Broseley

Broseley York Midi Bedienungsanleitung

Broseley

Broseley Hercules Bedienungsanleitung

Broseley

Broseley Desire Handbuch

Broseley

Broseley Evolution Endure Installationsanleitung

Broseley

Broseley Q7 Handbuch

Broseley

Broseley GB09b Bedienungsanleitung

Broseley

Broseley Canterbury Handbuch

Broseley

Broseley THURCROFT Betriebsanleitung

Broseley

Broseley Ignite 5 Handbuch

Broseley

Broseley York Midi Handbuch

Broseley

Broseley WINCHESTER Bedienungsanleitung

Broseley

Broseley York Grande Bedienungsanleitung

Broseley

Broseley Lincoln Handbuch

Broseley

Broseley 12B Handbuch

Broseley

Broseley Ignite 5 Handbuch

Broseley

Broseley IGNITE 5 CD1 MK2 Handbuch

Broseley

Broseley eVolution 4 Handbuch

Broseley

Broseley WINCHESTER Handbuch

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung

Barton

Barton FH-AMP8745 Technisches Dokument