Canon CREATIVE PARK (Moving) Performing white... Bedienungsanleitung
Before starting assembly : Writing the number of each section on
its back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after
cutting out the sections.)
Indicates where sections should be glued together.
Indicates the order for assembling parts.
Indicates where to insert sections.
Do not glue the sections together.
Round bar : Use to give parts a curved surface.
Tweezers : Useful in working with fine parts.
Cut along the line.
Be sure to build
this model carefully.
Caution : Performing horses' tricks require two pieces of thread, approximately 20cm long. Use silk or other durable thread.
* Turn the handle to make
the horses prance in time
with the trainer's baton.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Twelve A4 sheets (No. 1 to No. 12)
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
Caution : Spread glue in
a thin even layer,
then glue parts 7
and 8 to the base.
Glue parts 7, 8, and 10 to
the reverseside of part 1.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution : When viewed from
the side, parts 16
and 17 should be
aligned exactly.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution : Do not attach the front (part 3)
and back (part 6) to the base
at this stage.
Align the star marks when
gluing part 14 to part 8.
Parts 16, 17, and 18
Caution : Align the colored flaps when
gluing parts 20 and 22.
Wrap the end of a 20cm
piece of thread around
the axle two or three times.
Glue the thread firmly
in place.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Parts 20 to 22
Make two sets. Make two sets.
Make two sets.
Parts 23 to 26
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution : Hold the horses' bodies (part 30)
flat to prevent warping as you glue
on the other parts.
Make two sets.
Parts 40 and 41
Make two sets.
Confirm movement.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution :
Fold the legs carefully as
you glue them together
to prevent twisting.
Make two sets. Make two sets.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution : Do not attach part 28
and parts 42 through
44 at this stage.
Caution : Glue the legs so that they
are exactly aligned when
viewed from the side.
Make
two sets.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution : Do not attach the back
(part 6) at this stage.
Insert the support under each horse
into the square hole in the base and
glue the hind legs in place.
From inside the base,
align part 39 with flaps
on part 41 and glue
firmly in place.
* Using an empty box or a
similar item for a base makes
it easier to work with this model
when it is upside down.
* Horses are easier to attach if you
glue one leg at a time.
Glue the front (part 3) to the base.
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Caution : Take care when cutting
out the circular holes to
ensure that they are
smoothly rounded.
Caution : Position part 48 aligned with the upper
and lower inner wings on the right side
(marked with a star) and glue in place.
Insert the end of the
20cm thread into the
slot and glue it firmly
in place.
* The star indicates the left arm.
Confirm movement.
three
parts two
parts
(Moving) Performing white horses : Assembly Instructions ©
Canon Inc. ©
Hideharu Naitoh & G&P
Andere Canon Spielzeug Handbücher
Canon
Canon Creative Park Ragdoll Programmierhandbuch
Canon
Canon Creative Park Pop-up Card Halloween/Black cat &... Bedienungsanleitung
Canon
Canon Floral Teddy Bear Bedienungsanleitung
Canon
Canon CREATIVE PARK Pop-up ABC QRSTUVWX Bedienungsanleitung
Canon
Canon creative park Bedienungsanleitung
Canon
Canon CREATIVE PARK Moving Money Box: Pig Bedienungsanleitung
Canon
Canon Thoroughbred Bedienungsanleitung
Canon
Canon PAPER CRAFT MANEKI NEKO Bedienungsanleitung
Canon
Canon Creative Park Church of the Transfiguration Bedienungsanleitung
Canon
Canon Racer 539 Hawk Bedienungsanleitung
Canon
Canon PAPER CRAFT Bedienungsanleitung
Canon
Canon creative park Kurzanleitung
Canon
Canon CREATIVE PARK Paper Copter Bedienungsanleitung
Canon
Canon Creative Park Chinese Phoenix Bedienungsanleitung
Canon
Canon CREATIVE PARK Five-storied pagoda of Horvuji Temple,... Bedienungsanleitung
Canon
Canon CREATIVE PARK Temple of the Emerald, Thai Bedienungsanleitung
Canon
Canon Viva! Welcome to Circusland! Bedienungsanleitung
Canon
Canon Paper Craft Bedienungsanleitung
Canon
Canon Amerigo Teddy Bear Bedienungsanleitung
Canon
Canon PAPER CRAFT Whooper Swan Bedienungsanleitung
