Child Craft Crib'N'Double 31001 Bedienungsanleitung

Crib‘N’Double beD CoNverts

to toDDler beD or Full size

HeaDboarD & FootboarD

31001

assembly DireCtioNs aND Parts list

Directions for Maintenance, Cleaning, Storage and Use of your Crib/Toddler Bed are also included.

BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.

YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CRIB/TODDLER BED:

3Flat Tipped Screwdriver 3enclosedAllen Wrenches (A & B)

Parts eNCloseD iN HarDware bag

tHis is tHe assembly iNstruCtioNs

For Cribs solD iN tHe uNiteD states

Division of Foundations®Worldwide, Inc.

(12) Allenhead Bolts

(1) Allen Wrench

(6) Allenhead Bolts

D (4) Allenhead Bolts

(17) Allenhead Bolts

(16) Allenhead Bolts

J (2) Allenhead Bolts

(20) Connector Nuts

(16) Joint Connector Nuts

(2) Joint Connector Nuts

•5216 Portside Dr, Medina, OH 44256 USA •PH: 877.716.2757 (U.S. Only) or 330.722.5033 •FAX: 330.722.5037

•www.childcraftbaby.com

SI648E

Parts eNCloseD iN CartoN

Pouches

(storage for Assembly Directions)

(1) Long Foot Assembly

L (1) Short Foot Assembly

M (1) Short Head Assembly

(1) Short Foot Cap Rail

O (1) Short Head Cap Rail

(1) Stationary Post - Left

S (1) Stationary Post - Right

(1) Long Foot Cap

U (1) Spring

(1) Stretcher

(For use on Toddler Bed Only)

(2) Post Caps

(For use on Toddler Bed Only)

(1) Guard Rail Extender

(For use on Toddler Bed Only)

(1) Stationary Side Assembly

Q (1) Foot Post - Left R (1) Foot Post - Right

PreParatioN

Attach Stationary Posts S& Tby inserting Joint Connector Nuts Hinto the locator holes in the back face near top end of Stationary Side

Assembly Zand into bottom of the bottom rail of Stationary SideAssembly Z. Unslotted end of Joint Connector Nut Hwill be inserted into

hole. At the same time, insert Allenhead Bolts Cand Das shown in the diagram through posts. Thread Allenhead Bolts into Joint

Connector Nuts H. It may be necessary to use a at tip screwdriver in the slot at bottom of Joint Connector Nut Hto rotate it. This will

allow proper alignment of its threads with the thread on the Allenhead Bolts. Leave slightly loose until all bolts have been installed. Then

tighten all bolts securely using Allen Wrench A.

steP 1 - Diagram 1: attaCHiNg statioNary Posts to statioNary siDe

NOTE: Tighten securely means a good

snug t, do not allow the heads of bolts

and screws to dig into the wood.

These holes have a

large counterbore on

the opposite face.

Locate and place Dowel Pin

on end of Stationary Side Z

into this locator hole.

NOTE: Bolt D(which is

the longer bolt) will only

be installed in the lower

mounting holes.

Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE:

During the assembly process whenever using screws or bolts, check each with the Hardware List by letter and size

identication. Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size

specied in the assemblydirections.Ifanypartsaremissingorbrokenoryouneedassistancewithassembly,DONOTreturnthe product

toyourdealer.Call Foundations®for assistance at 877.716.2757 (U.S. Only) or 330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00

p.m. Eastern Time). Please identify the Crib’n’Double Bed by the model identication number stamped on the inside face of short head or short foot

assemblies, available when you call or write us at: Foundations®, 5216 Portside Dr, Medina, OH 44256 USA. Make note of all

identication numbers and include this information with your request. DO NOT SUBSTITUTE PARTS! Record your model identication

number here for future identication: Model #________________________

steP 2 - Diagram 2: assemble CaP rails to sHort HeaD aND Foot assemblies

Position Short Head Cap Rail Pabove Short Head Assembly Nas shown. Insert dowel pins in top rail of Short Head Assembly Ninto

receiving holes located in the bottom face of Short Head Cap Rail P. Then install two (2)Allenhead Bolts Finto receiving holes in bottom

edge of top rail on Short Head Assembly Nand thread into metal inserts. Once threads are engaged, tighten securely.

Follow this same procedure to attach Short Foot Cap Rail Oto Short Foot Assembly M using two (2) more of Allenhead Bolts F.

steP 3 - Diagram 3: attaCHiNg Foot Posts to sHort HeaD aND Foot assemblies

Attach Foot Post - Left Qto Short HeadAssembly Nby inserting Allenhead Bolts Fthrough their locator holes in Short HeadAssembly N

and threading into threaded inserts in Foot Post - Left Q. Tighten all Allenhead Bolts Fsecurely using Allen Wrench A.

Repeat this step to attach Attach Foot

Post - Right Rto Short Foot Assembly M.

NOTE:TheWarning label

will be positioned here.

Observe the orientation

of Short Head Cap Rail P

which has a shaped

narrow end.

Large Counterbore

Here

Threaded Insert

Shaped area will

be on outside face.

NOTE: The Warning label will be positioned

here. Observe the orientation of Short Head

Cap Rail Pwhich has a shaped narrow end.

Dowel Pins Threaded metal

insert in bottom

face (2) Places.

Outside Face

steP 4 - Diagram 4: attaCHiNg sHort HeaD assembly to statioNary siDe assembly

Attach Short Head Assembly Nto Stationary Side Assembly from Step 1. Allenhead Bolts Fwill be installed through receiving holes in

the end rail of Short HeadAssembly Nand threaded into the metal inserts installed in Stationary Post - Left S. Atotal of two (2) Allenhead

Bolts Fare required.

Repeat this step to attach Short Foot Assembly Mto Stationary Post - Right T.

steP 5 - Diagram 5: iNstalliNg loNg Foot assembly

Allow dowel pins on both ends of Long FootAssembly Lbottom rail to enter hole in posts Qand R. Joint Connector Nuts Hwill be installed

in the bottom edge of both the top and bottom rail of Long Foot Assembly Las each of the following bolts are installed (NOTE: Install

unslotted end of Joint Connector Nuts H into hole rst). Insert Allenhead Bolt Dthrough bottom hole in Foot Post Qand Rand into bottom

rail of Long Foot Assembly Land thread into Joint Connector Nut H as described in Step 1. Insert Allenhead Bolt Cinto the top hole and

also thread it into a Joint Connector Nut H. Tighten all bolts securely.Atotal of two (2) of Bolts Cand two of Bolts Dwill be used with four

(4) Joint Connector Nuts Hduring this process.

Stationary Side Assembly

from Step 1.

Short Foot Assembly from

Step 3 (this part is shown

after installation).

Short Head Assembly

from Step 3.

NOTE: Allenhead Bolt D

is longer than Allenhead

Bolt C.

Insert dowel on end of

bottom rail of Long Foot

Assembly Linto post Q

and R.

Threaded Insert

steP 7 - Diagram 7: attaCHiNg sPriNg to Crib

Before installing Spring V, determine the height for installation. Pull out “SwingArms” to the appropriate angle as shown. With the help of

a friend, carefully lower Spring Vinto the assembled crib to the selected height. Insert Allenhead Bolts Jinto the mounting holes in the

“SwingArms” and through the locator holes in Short Head and FootAssemblies Mand N. From the outside of the assembled crib, insert

connector Nuts Iinto the locator holes and thread onto Allenhead Bolts J. Tighten securely using Allen Wrench Awith bolts Jand Allen

Wrench Bwith Connector Nuts I.A total of four (4) of Iand Jare used to attach Spring V. Also install Allenhead Bolts Jand Connector

Nuts Iin the spring mounting position holes not used at this time.

To adjust height of Spring V, unthread all of the Allenhead Bolts J

and Connector Nuts Iand move Spring Vto the other height location

shown on the diagram. Then follow the same process for attaching the

Spring Vat its now location by following the process described above.

steP 6 - Diagram 6: attaCHiNg loNg Foot toP CaP

Attach Long Foot Top Cap Uto the crib assembly by lowering it down on top edge of Long Foot Assembly L. Allow the dowel pins in the

top of posts Qand R to t into the two receiving grooves. Also carefully align dowel pins in the top edge of Long Foot Assembly Lto enter

receiving holes in bottom face of Long Foot Top Cap U. Install ve (5) Allenhead Bolts Fthrough bottom edge of top rail in the Long Foot

Assembly Land carefully thread into the metal inserts in Long Foot Top Cap Ubottom face. Once aligned, thread bolts into inserts and

tighten securely using Allen Wrench A.This hole at each end will

receive dowel pin in Long

Foot Assembly Ltop rail.

Groove will

receive dowel

pins on top of

posts Qand R.

Threaded Inserts

(5 places)

“Swing Arms” rotated at

45º angle as shown.

Second possible

height location of

Spring V(these will

also be lled with parts

Iand Jto prevent

nger entrapment

of child.

ISwing

Arm on

spring.

Text on pouches should

face up during installation.

InsertAllenhead Bolts Jand Connector Nut Iinto empty holes in posts.Also installAllenhead Bolts Ewith Connector Nuts Ithrough edge

of posts Qand R. Each allenhead bolt will be securely threaded into a Connector Nut Iand tightened securely. Use Allen Wrenches A

and B to securely threaded these items together. Filling these holes will add security to the crib by prevent nger entrapment for the child.

Before using crib, refer to page 12 and 13 for Warnings and maintenance of the crib.

steP 8 - Diagram 8: FilliNg emPty Holes

Receiving hole

through post Q

and R(2 total)

NOTE: This hole was

provided for the

attachment of a guard

rail (if desired) when crib

is converted to a Toddler

Bed.

Install two (2) of Iand J

through each of the (4)

posts as shown.

NOTE: These holes were

provided to allow the

conversion of the crib to

a full bed.

When use as a crib has been completed, you have the option to convert to a Toddler Bed for years of additional use in your child’s room.

Remove mattress. Spring Vmust be installed in lowest position. Remove and store (see Storage on page 12) Long Foot Top Cap U

and Long Foot Assembly L. Refer to Steps 6 and 5 and perform these steps in reverse to remove these parts.

Store away all parts and hardware removed in the event you wish to convert your Toddler Bed to a Crib. DO NOT store extra hardware

in pouch attached to spring.

steP 9 - Diagram 9: CoNvert “Crib” to a“toDDler beD”

Gently stretch posts Q

and Raway from each

other to allow space for

the dowels on Stretcher

Insert dowel pin

on end of

Stretcher Winto

receiving hole in

posts Qand R.

Install Stretcher Wby gently stretching foot posts Qand Raway from each other just enough to allow wood dowels in the ends of Stretcher

W to t into the receiving holes in the posts Qand R. If this does not allow adequate room, then it may be necessary to temporarily unbolt

one of the bolts securing the Spring Vto the crib and reconnecting it once Stretcher Wis installed. InstallAllenhead Bolts D(just removed

during the removal of Long FootAssembly L) through receiving hole near bottom of posts Qand Rand thread into a Joint Connector Nut

Gwhich is to be installed in the bottom edge of Stretcher W(part Gis a part not previously used and should have been stored away once

the crib was assembled). Tighten bolts Dsecurely using Allen Wrench A.

Align dowel pins in top of posts Qand Rwith holes in Post Caps Xand press Post Caps Xdown over dowel pins. Insert Allenhead Bolts

Kthrough hole in Post Caps Xand tighten securely into threaded insert in top of posts Qand Rusing Allen Wrench A.

steP 10 - Diagram 10: attaCH Post CaPs to Posts

Post Cap X shown

installed here.

Threaded Insert

Insert Allenhead Bolts Eand Connector Nuts Iinto the empty holes in posts Qand R. Tighten securely using Allen Wrench Aand B.

IMPORTANT! refer to warnings on page 10 before using as Toddler Bed.

steP 11 - Diagram 11: FilliNg emPty Holes iN Posts

(2) Empty holes in each

foot posts Qand R

(bolts and connectors

shown installed in this

post)

iNstalliNg a guarD rail

A Guard Rail can be purchased for added security. Follow the

directions on the instruction sheet included with the Guard Rail.

You will need (2) Guard Rail Extenders Yand (4) of Allenhead

Bolts Dfrom this crib.

Fill all empty holes in Foot Posts Qand Ras directed in Step 11.

ENTRAPMENT. Openings in and between bed parts can entrap head and neck

of a small child. NEVER use bed with children younger than 15 months.

ALWAYS follow assembly instructions.

over bed. NEVER place items with a string, cord or ribbon, such as hood strings

or pacier cords, around a child’s neck. These items may catch on bed parts.

(1310 mm) in length, 27 1/4 in. (690 mm) in width, and 4 in. (100 mm) in thickness.

•The users maximum weight shall not be greater than 50 lbs. (22.7 kg).

•Mattress MUST be moved into lowest position for proper positioning behind

stretcher.

•This crib contains all components necessary to convert to a toddler bed. However,

a guardrail may be available for purchase to provide additional security. Contact

Foundations®for assistance. Refer to maintenance section for contact information.

!(For Toddler Bed)

WARNING

:INFANTS HAVE DIED IN TODDLER BEDS FROM

WARNING

:STRANGULATION HAZARD: NEVER place bed near windows

where cords from blinds or drapes may strangle a child. NEVER suspend strings

CAUTION:

ENTRAPMENT HAZARD: To avoid dangerous gaps

any mattress used in this bed shall be a full-size crib mattress at least 51 5/8 in



Andere Child Craft Baby- und Kleinkindmöbel Handbücher

Child Craft

Child Craft Delaney F01616 Bedienungsanleitung

Child Craft

Child Craft DOUBLE DROPSIDE CRIB Bedienungsanleitung

Child Craft

Child Craft Legacy Crib Bedienungsanleitung

Child Craft

Child Craft Long Beach F22101 Bedienungsanleitung

Child Craft

Child Craft Forte Flat Top Crib F34301 Bedienungsanleitung

Child Craft

Child Craft Kieran F33201 Bedienungsanleitung

Child Craft

Child Craft 10031 Bedienungsanleitung

Child Craft

Child Craft Wadsworth 31301 Bedienungsanleitung

Child Craft

Child Craft Wynwood F11501 Bedienungsanleitung

Child Craft

Child Craft CRIB'N'DOUBLE BED Bedienungsanleitung

Child Craft

Child Craft Elin F37101 Bedienungsanleitung

Child Craft

Child Craft Cranbrook F33301 Bedienungsanleitung

Child Craft

Child Craft Orbit F30201 Bedienungsanleitung

Child Craft

Child Craft Bristol F99040 Bedienungsanleitung

Child Craft

Child Craft Monterey F10391 Bedienungsanleitung

Child Craft

Child Craft F99106.26 Bedienungsanleitung

Child Craft

Child Craft 1216 Bedienungsanleitung

Child Craft

Child Craft Crib'N'Double Bed Bedienungsanleitung

Child Craft

Child Craft Redmond F32801 Bedienungsanleitung

Child Craft

Child Craft F01216 Bedienungsanleitung

Child Craft

Child Craft Surrey Hill F37001 Bedienungsanleitung

Child Craft

Child Craft FOREVER ECLECTIC HAMPTON Arch-Top Crib Bedienungsanleitung

Child Craft

Child Craft Parisian Full Size Wood Crib F12301 Bedienungsanleitung

Child Craft

Child Craft Redmond F32801 Bedienungsanleitung

Beliebte Baby- und Kleinkindmöbel Handbücher anderer Marken

Mocka

Mocka Learning Tower Bedienungsanleitung

VERTBAUDET

VERTBAUDET 62003-2789 Bedienungsanleitung

Summer

Summer MY FUN POTTY Bedienungsanleitung

Grotime

Grotime Changeover Bedienungsanleitung

Fillikid

Fillikid 1221 Bedienungsanleitung

Relita

Relita loft bed ALEX Bedienungsanleitung

Joovy

Joovy Qool Bedienungsanleitung

KidKraft

KidKraft Step n Store Bedienungsanleitung

Fisher-Price

Fisher-Price L4889 Bedienungsanleitung

Germania

Germania Moon 4048.101 Bedienungsanleitung

BabyGo

BabyGo Amila Bedienungsanleitung

Fisher-Price

Fisher-Price CBV06 Bedienungsanleitung

Fisher-Price

Fisher-Price H4790 Bedienungsanleitung

Graco

Graco Dream Suite Bedienungsanleitung

Delta Childrens Products

Delta Childrens Products BB87116CR Bedienungsanleitung

Costway

Costway BB5591 Bedienungsanleitung

SAUTHON

SAUTHON UP CHENE DORE UI101A Bedienungsanleitung

Delta Children

Delta Children Classic Bedienungsanleitung