Cisco MC3810 Series Bedienungsanleitung

OBTAIN TOOLS AND EQUIPMENT

INSTALL CHASSIS AND CONNECT CABLES

GET SITE INFORMATION

POWER UP THE CISCO MC3810

PERFORM INITIAL CONFIGURATION

Telephone

network

SNA Video

codec

Video

Computer

Digital or

analog PBX

Cisco

MC3810

Ethernet

hub

T1/E1 or nX64K

Quick Start Guide

CISCO MC3810 SERIES

MULTISERVICE ACCESS CONCENTRATORS

INSTALLATION AND STARTUP

Obtain Tools and Equipment

Items Included

• Cisco MC3810 multiservice access concentrator

• Rack-mountbrackets,powercord,andspareset

of rubber feet

• RJ-45-to-DB-9 female DTE adapter (labeled

TERMINAL)

• RJ-45-to-DB-25 female DTE adapter (labeled

TERMINAL)

• RJ-45-to-DB-25 male DCE adapter (labeled

MODEM)

• RJ-45-to-RJ-45 rollover console cable

•Quick Start Guide (this document)

• Cisco MC3810 Series Multiservice Access

Concentrators Hardware Installation Guide

• Cisco MC3810 Multiservice Access

Concentrators Software Conﬁguration Guide

• Cisco MC3810 Multiservice Access

Concentrators Regulatory Compliance and

Safety Information

• Installing and Removing Field-Replaceable

Units in Cisco MC3810 Series Multiservice

Access Concentrators

• Cisco IOS release notes

• Documentation CD-ROM

• Product warranty card

• Cisco Information Packet

• Cisco information wallet card and sticker

Items Not Included

• Four screws for installing the chassis in a rack

• E1 channel service unit/data service unit

(CSU/DSU)

• PC running terminal emulation software for

administrative access

• Modem for remote administrative access

• Ethernetcable:RJ-45-to-RJ-45straight-through

• T1/E1 cable: RJ-48-to-RJ-48 straight-through

• Cisco synchronous serial transition cable for

connecting a serial port to EIA/TIA-232,

EIA/TIA-449, V.35, X.21, or EIA-530

• Digital voice cable: RJ-48-to-RJ-48 rollover

• Analog voice cables, FXO or FXS:

RJ-11-to-RJ-11 straight-through

• Analog voice cables, E&M: 8-conductor

straight-through

• BRI S/T cables: 8-conductor straight-through

and 8-conductor rollover

• CTR17 adapter for connecting E&M 4-wire per

ETSI CTR17

Ordering Information

To place an order, contact Cisco Customer Service

(408 526 4000 or 800 553 6387).

Install Chassis and Connect Cables

Front panel forward

Rear panel forward

2356

T1/E1

E&M

E&M FXO

Rear panel forward,

center-mount telco

FXO FXO

2356

E&M FXO

E&M

E&M E&M

T1/E1

Safety Information

Warning See the Cisco MC3810 Series

Multiservice Access Concentrators

Hardware Installation Guide for safety

information you need to know before

working on the Cisco MC3810.

Desktop Installation

Caution If you place the Cisco MC3810

on a desktop, do not place anything that

weighs more than 10 pounds

(4.5 kilograms) on top of the chassis.

Caution Do not remove the rubber feet.

They provide a space for air circulation.

Rack-Mounting the Chassis

Step 1 Choose one of the methods shown in the

above ﬁgure, and attach the mounting

brackets as shown.

Note: Brackets are included. Screws are included

for attaching the brackets to the chassis, but not for

installing the chassis in a rack. You need four

additional screws to install the chassis in a rack.

Step 2 Install the chassis in the rack.

Install Chassis and Connect Cables (continued)

Vertical

wall stud

Power supply

and fan at the top

Wall-Mounting the Chassis

Step 1 Install the smaller brackets as shown in

the ﬁgure above.

Step 2 Attach the chassis to the wall.

• Positiontheendnearestthepower cable

at the top

• Align screws with a wall stud, or use

wall anchors

Note: Screws for attaching the chassis to a wall are

not included. You need to provide four screws

suitable for your wall installation.

Caution Do not remove the rubber feet.

They provide a space for air circulation.

Install Chassis and Connect Cables (continued)

Identifying Cable Types

8-Conductor Rollover Cable

Hold the connectors side-by-side, with the tab at the

back. The colored wires are in the opposite sequence

atoppositeendsof thecable. Ifyourcablecamefrom

Cisco Systems, pin 1 is white on one plug, and pin 8

is white on the opposite plug. (A rollover cable

reverses the wire connections at the opposite ends:

1to8,2to7,3to6,4to5,5to4,6to3,7to2,and

8 to 1.)

8-Conductor Straight-Through Cable

Hold the connectors side-by-side, with the tab at the

back. The colored wires are in the same sequence at

opposite ends of the cable. (A straight-through cable

connectslike-numbered pinsatoppositeends: 1 to1,

2to2,3to3,4to4,5to5,6to6,7to7,and8to8.)

RJ-48 T1/E1 Cable

Viewtheconnector fortheCiscoMC3810port,with

the tab at the back. There are wires attached to four

ofthe pins: 1, 2, 4, and5.(Thepinoutatthe opposite

end depends on the interface at that end.)

Pin 1 Pin 8

Same color

Pin 1

Same color

Pin 1

Install Chassis and Connect Cables (continued)

Cisco MC3810

FXO FXO

2356

E&M FXO

E&M

E&M E&M

T1/E1 trunk port

(RJ-48 shown)

RJ-48 straight-through cable

or two 75-ohm coaxial

cables with BNC connectors

(not shown)

T1/E1

Network demarcation

(RJ-48 shown)

Connecting the T1/E1 Trunk

Port to the Network

If you are using a T1/E1 network interface, connect

the T1/E1 trunk port to a network demarcation

device.

If the trunk port has an RJ-48 jack, use an RJ-48

straight-through cable (not included), or a special

cable if required for your application.

If the trunk port has BNC connectors, use two

75-ohm coaxial cables with BNC connectors (not

included).

Note: The T1/E1 trunk port, when present, has a

built-in CSU/DSU for connection to a service

provider’s network interface.

Step 1 For an RJ-48 cable—Connect one end of

the cable to the RJ-48 jack labeled T1/E1

on a light-green background.

For coaxial cables—Connect one end of

the cables to the BNC connectors labeled

E1 on a light-green background.

Note: Be sure to make the correct transmit and

receive connections for both 75-ohm cables.

Step 2 Connect the other end of the cable(s) to

the network demarcation device (telco

demarc or equivalent).

Install Chassis and Connect Cables (continued)

Cisco MC3810

2356

ISDN wall jack

(U interface)

BRI S/T backup port

(CB-1D)

8-conductor

straight-through

cable

NT1

S/T U

T1/E1

BRI 0 S/T

ConnectingtheBRIS/TBackup

Port to the Network

If your Cisco MC3810 supports BRI S/T backup,

connect the BRI S/T backup port to the ISDN

network.

Use an 8-conductor straight-through cable (not

included).

Step 1 Connect one end of the cable to the port

labeled BRI 0 S/T on an orange

background.

Step 2 Connect the other end of the cable to the

S/T interface of the NT1.

Step 3 If the NT1 is not already connected to the

ISDN network, connect the U interface of

the NT1 to the ISDN wall jack

(U interface).

Note: Step 3 should only be necessary in locations

wheretheU interface is accessible to the user, such as

in the United States.

Install Chassis and Connect Cables (continued)

Cisco MC3810

CSU/DSU

Serial 1

port

Serial 0

port

Cisco serial

transition

cables

FXO

2356

E&M FXO

E&M

E&M E&M

T1/E1

Connecting Synchronous

Serial Ports

You can connect the serial 0 port to a Frame Relay

network or to user equipment.

You can connect the serial 1 port to user equipment.

Use one of the Cisco serial transition cables (not

included). Select the cable to match both of the

following parameters:

• Signaling protocol:

—EIA/TIA-232

—EIA/TIA-449

—V.35

—X.21

—EIA-530

• Cisco MC3810 serial port operating mode:

—DTE

—DCE

See the Cisco MC3810 Series Multiservice Access

Concentrators Hardware Installation Guide for

information about selecting these cables.

Note: Both serial ports are dark blue.

Step 1 Connectthe60-pin connector of the serial

transition cable to the Cisco MC3810

serial port to be used for this interface.

Step 2 Connect the other end of the serial

transition cable to the CSU/DSU,

synchronous modem, or video codec.

Install Chassis and Connect Cables (continued)

Ethernet hub

Cisco MC3810

Straight-through

Ethernet cable

10BaseT port

(RJ-45)

2356

E&M FXO

E&M

E&M E&M

T1/E1

Connecting the Ethernet Port

for LAN Access

If you are using a 10BaseT Ethernet LAN, connect

the Ethernet 0 port to the Ethernet hub.

Use a standard, straight-through, 10BaseT Ethernet

cable (not included).

Step 1 Connect the cable to the Ethernet 0 port

(yellow).

Step 2 Connect the other end of the cable to an

Ethernet hub.

Inhaltsverzeichnis

Andere Cisco Netzwerk-Hardware Handbücher

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Bedienungsanleitung

Cisco

Cisco ONS 15454 Bedienungsanleitung

Cisco

Cisco MGX 8260 Kurzanleitung

Cisco

Cisco ISA 3000 Kurzanleitung

Cisco

Cisco Aironet 1000 Series Handbuch

Cisco

Cisco Firepower 1010 Series Handbuch

Cisco

Cisco NCS 4206 Bedienungsanleitung

Cisco

Cisco IPS-4240-K9 - Intrusion Protection Sys 4240 Bedienungsanleitung

Cisco

Cisco DOC 785983 Bedienungsanleitung

Cisco

Cisco Firepower 9300 Handbuch

Cisco

Cisco Catalyst 8300 Series Handbuch

Cisco

Cisco 7606 Bedienungsanleitung

Cisco

Cisco ONS 15310-MA SDH Handbuch

Cisco

Cisco Catalyst 2960-XR Bedienungsanleitung

Cisco

Cisco ONS 15600 Bedienungsanleitung

Cisco

Cisco ISA500 Series Bedienungsanleitung

Cisco

Cisco 3660 Series Bedienungsanleitung

Cisco

Cisco ASA 5506-X Handbuch

Cisco

Cisco AIR-BR350-A-K9 - Aironet 350 Wireless Bridge Handbuch

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Bedienungsanleitung

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Bedienungsanleitung

Cisco

Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Bedienerhandbuch

Cisco

Cisco ONS 15454 Handbuch

Cisco

Cisco IAD1101 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung