Cisco TelePresence Server 7010 Bedienungsanleitung

Cisco TelePresence

TelePresence Server 7010

Installation Guide

61-0028-06

August 2013

Cisco TelePresence Server 7010 Installation Guide Page 1 of 14

Contents

General information 3

About the Cisco TelePresence Server 7010 3

Package contents 3

Port and LED locations 3

LED behavior 4

Front panel LED behavior 4

Rear panel LED behavior 4

Connecting the TelePresence Server 6

Before you start 6

Task 1: Connect power 6

Task 2: Connect to Ethernet Port A 6

Configuring the TelePresence Server 7

Task 3: Connect to the console port 7

Task 4: Configure Ethernet Port A settings 7

Task 5: Assign an IP address to the TelePresence Server (optional) 7

Task 6: Discover the IP address of the TelePresence Server 8

Task 7: Log in to the TelePresence Server 8

Configuring the TelePresence Server software 9

Task 8: Configure settings, conferences, and endpoints 9

Checking for updates 10

Replacing the power supply 11

Troubleshooting and technical support information 12

Using the event log to help solve a problem 12

Getting more help 12

Technical specifications 13

Power requirements 13

Over-current protection 13

Operating environment 13

Anti-static precautions 13

Cisco TelePresence Server 7010 Installation Guide Page 2 of 14

General information

About the Cisco TelePresence Server 7010

The Cisco TelePresence Server 7010 (TelePresence Server) is a technologically advanced media processor,

combining continuous presence high definition video conferencing and the highest possible voice quality.

Package contents

The following items are included with the TelePresence Server. Verify that you have these items before

installing the device:

nConsole cable

nPower cable

nRack mounting kit

Port and LED locations

The following diagrams show the positions of ports and LEDs on the front and rear of the unit.

Figure 1: TelePresence Server 7010 front panel

USB Console

Active

StatusAlarm

Net

TS 7010

USB ports and

activity LEDs

LCD status

display

Air

intake

Alarm

LED

Status

LED

Console

port

Ethernet activity LEDs

(for ports on rear panel)

Cisco TelePresence Server 7010 Installation Guide Page 3 of 14

General information

Figure 2: TelePresence Server 7010 rear panel

1000

100

FDX

Ethernet B

1000

100

FDX

Ethernet C

1000

100

FDX

Ethernet D Admin

100

FDX

Link In

Link

Link Out

Link

1000

100

FDX

Ethernet A

Air exhaust Link connectors

Power supplyEthernet ports and status LEDs Admin port and status LEDs Power supply latch

Protective earth terminals

LED behavior

Front panel LED behavior

The following table describes the behavior of the LEDs on the front of the TelePresence Server.

LED Color Indicates

Status Green The unit is operating normally

Alarm Red The unit is booting or has developed a fault, for example:

ntemperature is outside normal limits

ninternal fan failure detected

See the web interface for more information about the problem (go to the

configuration page for your unit)

USB Activity Reserved for future expansion

Rear panel Ethernet

activity

Green Activity on rear panel Ethernet port A, B, C and D

Table 1: TelePresence Server 7010 front panel LED behavior

Rear panel LED behavior

The following table describes the behavior of the LEDs on the rear of the unit.

Note: The front panel LCD will show the IP address assigned.

LED Color Indicates

Ethernet Port Status:

Table 2: TelePresence Server 7010 rear panel LED behavior

Cisco TelePresence Server 7010 Installation Guide Page 4 of 14

General information

LED Color Indicates

FDX Green The link has been established as a full-duplex link

100 Green The link is operating at 100Mbps. This LED flashes to indicate activity

1000 Green The link is operating at 1000Mbps. This LED flashes to indicate activity

Admin Port Activity Reserved for future expansion

Link Connectors Reserved for future expansion

Cisco TelePresence Server 7010 Installation Guide Page 5 of 14

General information

Connecting the TelePresence Server

Before you start

IMPORTANT: Before installing the TelePresence Server, you must read the safety information at

http://www.cisco.com/go/telepresence/safety.

Task 1: Connect power

Connect the power connector on the rear of the unit to the power supply using the supplied power cable.

(There is no On/Off switch.)

Task 2: Connect to Ethernet Port A

Connect an Ethernet cable from Ethernet Port A to an Ethernet switch (rather than a hub, to minimize

interference from other devices on the network). The Ethernet port is a 10/100/1000Mbps auto-sensing

connection.

Ethernet Ports B, C and D may not be supported in the software supplied with your TelePresence

Server. Do not connect to these ports unless the web interface allows you to configure them. Do not

connect multiple ports to the same subnet unless instructed to do so by the web interface.

Cisco TelePresence Server 7010 Installation Guide Page 6 of 14

Connecting the TelePresence Server

Configuring the TelePresence Server

Task 3: Connect to the console port

1. Ensure power is connected to the TelePresence Server and the Status LED is green. A status LED that is

not lit indicates the unit is still booting.

2. Connect the console port of the unit to the serial port of your PC using the RJ45 to DB9 cable supplied.

3. Use a serial terminal program, such as Secure CRT or HyperTerminal, to connect to the unit. Set your

terminal software to the following settings:

lBaud rate: 38400

lData bits: 8

lParity: none

lStop bits: 1

lFlow control: none

4. Press Enter and the following command prompt appears on the terminal:

TS:>

Task 4: Configure Ethernet Port A settings

The default setting for the TelePresence Server Ethernet ports is auto-sensing mode. If the switch port to

which you connect the TelePresence Server is not also set to auto-sensing mode, then you need to configure

the device's Ethernet port to use the same speed and duplex mode.

Note:To establish a 1000Mbps connection, both ends of the link must be configured as auto-sensing.

nTo configure Ethernet Port A, enter the following for auto-sensing mode:

ethertype A auto

or to configure a speed and duplex, use the following command:

ethertype A <10 | 100> <half | full>

For example, to configure a full-duplex 100 Mbps link, enter:

ethertype A 100 full

nTo display the current configuration and status of the Ethernet ports, enter:

status

Task 5: Assign an IP address to the TelePresence Server

(optional)

The default setting for the TelePresence Server is to use DHCP to obtain an IP address. You can assign a

static IP address if you prefer, or if a DHCP server is not available. If you want the IP address of the

TelePresence Server to be assigned by your DHCP server, omit this step.

The TelePresence Server supports IPv4 and IPv6 addressing. The default configuration for Port A is:

Port A will acquire an IPv4 address using DHCP; IPv6 is disabled.

nTo assign a static IPv4 address to Port A, use the following command:

static A <IP address> <netmask> [<default gateway address>]

Note:If you do not have a DNS server, use 0.0.0.0 as the DNS server IP address.

Cisco TelePresence Server 7010 Installation Guide Page 7 of 14

Configuring the TelePresence Server

For example, to assign an address of 192.168.1.2 where the default gateway is at 192.168.1.1, enter:

static A 192.168.1.2 255.255.255.0 192.168.1.1 0.0.0.0

nTo manually specify a DNS server, use this command:

dns <DNS server address> [<secondary DNS server>][<domain>]

nTo revert to using DHCP after setting a static IPv4 address, use the following command:

dhcp -4 A

For information on assigning a static IPv6 address type help static. For information on assigning an

automatic IPv6 address type help dhcp or else see the online help.

Task 6: Discover the IP address of the TelePresence Server

1. To display the current status of the IP address, enter: status

If you have DHCP enabled on your network and you are allowing the TelePresence Server to acquire its

address using DHCP, the IP address that has been acquired by Ethernet Port A will be shown; if you

have assigned a static IP address, that is the address that will be shown.

2. Make a note of the IP address. You will use this to access the web interface of the unit.

Note:When your TelePresence Server has an IPaddress, you can add an entry for it on your DNSserver

and use a hostname to access the device's web interface.

Note:The front panel LCD will show the IP address assigned.

Task 7: Log in to the TelePresence Server

To log in to the web interface of the device:

1. Use your browser to navigate to the IP address or hostname of the unit.

2. Enter the user name admin with no password, and click Log in.

The Status page is displayed.

Note: We recommend that you change the admin account to use a password as soon as possible. To do

that, go to Configuration > Change password and type in the new password twice.

Cisco TelePresence Server 7010 Installation Guide Page 8 of 14

Configuring the TelePresence Server

Configuring the TelePresence Server software

Task 8: Configure settings, conferences, and endpoints

You may need to configure the network and system settings, then go on to add conferences and endpoints.

Refer to the online help for assistance.

Cisco TelePresence Server 7010 Installation Guide Page 9 of 14

Configuring the TelePresence Server software

Checking for updates

It is a good idea to regularly check the Cisco web site for updates to the device's main software. This section

describes how to upgrade the device using the web interface.

To check for, and download, updates:

1. Log in to the web interface and go to Status > Status.

2. Make a note of the software version that is currently installed.

3. Go to the support section of the web site and check if a more recent release is available.

4. If a more recent release is available, download it and save it locally.

To upgrade the software application:

1. Unzip the software release file that you downloaded.

2. In the web interface, go to Configuration > Upgrade.

3. In the Main software image section, click Browse and locate the unzipped file.

4. Click Upload software image.

The browser begins uploading the file to the device, and a new browser window opens to indicate the

progress of the upload. When finished, the browser window refreshes and indicates that the software

upgrade is complete.

5. Go to Configuration > Shutdown to shut down and restart the device.

Note:Shutting down the device will disconnect all participants.

Cisco TelePresence Server 7010 Installation Guide Page 10 of 14

Checking for updates

Andere Handbücher für TelePresence Server 7010

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS C220 M3 Installations- und Betriebshandbuch

Cisco

Cisco Cisco MeetingPlace Express Betriebsanleitung

Cisco

Cisco UCS C24 Montage- und Wartungsanleitung

Cisco

Cisco UCS B460 M4 Bedienungsanleitung

Cisco

Cisco Firepower 1120 Bedienungsanleitung

Cisco

Cisco APIC M3 Montage- und Wartungsanleitung

Cisco

Cisco UCS 5100 Handbuch

Cisco

Cisco UCS C200 Handbuch

Cisco

Cisco UCS 5100 Kurzanleitung

Cisco

Cisco UCS E Series Handbuch

Cisco

Cisco IP/TV 3400 Series Bedienungsanleitung

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco UCS C220 M5SX Bedienungsanleitung

Cisco

Cisco TelePresence Bedienungsanleitung

Cisco

Cisco VPN 3002 Hardware Client Manager Bedienungsanleitung

Cisco

Cisco ONS 15600 Bedienungsanleitung

Cisco

Cisco Digital Media System 3.5 Bedienungsanleitung

Cisco

Cisco UCS C240 M3 Bedienungsanleitung

Cisco

Cisco AS5300 - Universal Access Server Bedienungsanleitung

Cisco

Cisco SNS-3515 series Bedienungsanleitung

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco UCS B200 M3 Handbuch

Cisco

Cisco GSS-4492R-K9 Bedienungsanleitung

Cisco

Cisco UCS B460 M4 Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung