Cisco UCS B460 M4 Bedienungsanleitung

Contents

Introduction

Prerequisites

Requirements

Components Used

Background

Discovery Problems

Discovery Fails at 3% - Firmware Mismatch

Solution

Discovery Fails at 7% - CPU Mismatch

Solution

Introduction

This document describes two possible discovery failures that can occur when a B460 M4 motherboard is replaced and their respective solutions.

Prerequisites

Requirements

This document assumes knowledge of UCS B460 M4 and UCS Manager (UCSM).

Components Used

B460 M4 Blade Server

●

UCS Manager

●

Firmware 2.2(3b)

●

Background

The B460 M4 server consists of two Scalable M4 Blade Modules (B260 M4) and a Scalability Connector that cross-connects the two Blade Modules and

allows them to function as a single server. The Blade Module on the bottom is the “Master” and the Blade Module on the top is the “Slave.”

Discovery Problems

Discovery Fails at 3% - Firmware Mismatch

In this failure scenario, the discovery fails at 3% with Remote Invocation Description Aggregate blade CIMC firmware version mismatch. Activate same

firmware version on both CIMC as shown in the figure below. This can occur due to the replacement motherboard or blade module having a different

firmware than the pre-existing B460 M4 server.

The Overall Status will be Discovery Failed as shown in the figure below.

The mismatched firmware can be checked from the command line (CLI) as shown below. In the

output below, the first CIMC is the master and the second is the slave.

UCS-A# show system firmware expand detail

Server 7:

CIMC:

Running-Vers: 2.2(3b)

Package-Vers:

Update-Status: Ready

Activate-Status:

Startup-Vers:

Backup-Vers: 2.2(3a)

Bootloader-Vers: 2.2(3b).33

CIMC:

Running-Vers: 2.2(3a)

Package-Vers:

Update-Status: Ready

Activate-Status:

Startup-Vers:

Backup-Vers: 2.2(3b)

Bootloader-Vers: 2.2(3a).33

CIMC:

Running-Vers: 2.2(3b)

Package-Vers: 2.2(3b)B

Update-Status: Ready

Activate-Status: Ready

Startup-Vers: 2.2(3b)

Backup-Vers: 2.2(3b)

Bootloader-Vers: 2.2(3b).33

Solution

In order to recover from this, follow the steps below.

1) Navigate to Equipment > Chassis > Chassis # > Servers > Server # > Installed Firmware tab.

2) Right-click on the component that needs to be updated (e.g. BIOS, CIMC Controller) and select Update Firmware. In this example, the CIMC Controller

will be updated to 2.2(3b).

3) Select the correct firmware, the Force checkbox and click Apply.

Tip: If it's not clear which version needs to be selected from the dropdown, the network

administrator can navigate to Equipment > Firmware Management > Packages, expand

ucs-k9-bundle-b-series.VERSION.B.bin and look for "ucs-EXM4." There will be three

components: bios (BIOS), brdprog (Board Controller), and cimc (CIMC Controller).

4) Monitor the Installed Firmware tab and wait until the Update Status and Activate Status columns change to Ready and the Backup Version column

changes to the correct firmware.

Tip: The server administrator can monitor the update status from Equipment > Chassis >

Chassis # > Servers > Server # > Inventory tab > CIMC tab > Update Status

5) Right-click on this same component and select Activate Firmware. Again, select the correct firmware, the Force checkbox and click Apply.

6) The Activate Status column in the Installed Firmware tab will change state and eventually return to Ready.

7) The Overall Status in the General tab will change to Inaccessible while the server is rebooting. It should then change to Discovery and go through the

discovery process.

Discovery Fails at 7% - CPU Mismatch

In this failure scenario, the discovery fails at 7% with Remote Invocation Description Pre-boot Hardware config failure - Look at POST/diagnostic results

as shown in the figure below.

The Overall Status in the General tab will be Compute Failed.

The POST Results can be verified by clicking the View Post Results under Actions in the General tab. The figure below shows that the problem is due to a

CPU Mismatch.

Solution

If the hardware matches between the two blade modules, this could be caused by cached information on the server. An enhancement request (CSCuv27099)

exists to clear the cached information from UCS Manager (UCSM). The server administrator can also contact the Cisco Technical Assistance Center (TAC)

for a workaround.

Andere Handbücher für UCS B460 M4

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS C200 M2 Systemhandbuch

Cisco

Cisco UCS Invicta C3124SA Handbuch

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco CDE 220 Series Handbuch

Cisco

Cisco UCS C220 M3 Montage- und Wartungsanleitung

Cisco

Cisco UCS C220 Bedienungsanleitung

Cisco

Cisco UCS E Series Handbuch

Cisco

Cisco PDS2000 Bedienungsanleitung

Cisco

Cisco UCS C260 Montage- und Wartungsanleitung

Cisco

Cisco UCS C3160 Montage- und Wartungsanleitung

Cisco

Cisco UCS B200 M2 Bedienungsanleitung

Cisco

Cisco TelePresence Server 7010 Bedienungsanleitung

Cisco

Cisco AS5300 - Universal Access Server Bedienungsanleitung

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco SNS-3415 series Programmierhandbuch

Cisco

Cisco C880 M4 Montageanleitung

Cisco

Cisco 7835-H2 - Media Convergence Server Bedienungsanleitung

Cisco

Cisco N20-B6625-1 Systemhandbuch

Cisco

Cisco UCS C460 Montage- und Wartungsanleitung

Cisco

Cisco UCS X9508 Bedienungsanleitung

Cisco

Cisco UCS C22 M3 Systemhandbuch

Cisco

Cisco CSACS-1121-K9 Bedienungsanleitung

Cisco

Cisco UCS C240 M4 Montage- und Wartungsanleitung

Cisco

Cisco SNS-3515 series Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung