Cisco UCS B200 M3 Handbuch

Send document comments to [email protected]

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco UCS B200 M3 Blade Server Installation and

Service Note

The Cisco UCS B200 M3 (shown in Figure 1) is the latest Cisco Intel-based, half-width blade supporting

two CPU sockets using Intel E5-2600 series CPUs and up to 24 DIMMs; it supports one modular LOM

(dedicated slot for Cisco's Virtual Interface Card) and one mezzanine adapter. At this time, the UCS

B200 M2 (second generation) server is still available and is documented elsewhere. You can install up

to eight UCS B200 Blade Servers to a UCS chassis, mixing with other models or Cisco UCS blade

servers in the chassis if desired. The Cisco UCS B200 M3 is managed by Cisco UCS Manager version

2.0(2m) and later.

Figure 1 Cisco UCS B200 M3 Front Panel

1Asset tag 1

1.Each server has a blank plastic tag that pulls out of the front panel which is provided so that you can add your own

asset tracking label without interfering with the intended air flow.

7Network link status LED

2Blade ejector handle 8Blade health LED

3Ejector captive screw 9Console connector

4Hard drive bay 1 10 Reset button access

5Hard drive bay 2 11 Beaconing LED and button

6Power button and LED

UCS B200 M3

1 2 3 678910 11

331360

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

LEDs

Server LEDs indicate whether the blade server is in active or standby mode, the status of the network

link, the over all health of the blade server, and whether the server is set to give a flashing blue beaconing

indication. See Table 1 for details.

The removable hard disks also have LEDs indicating hard disk access activity and hard disk health.

Buttons

The Reset button is just inside the chassis and must be pressed using the tip of a paper clip or a similar

item. Hold the button down for five seconds, and then release it to restart the server if other methods of

restarting are not working.

Table 1 Blade Server LEDs

LED Color Description

Power Off Power off.

Green Normal operation.

Amber Standby.

Link Off None of the network links are up.

Green At least one network link is up.

Health Off Power off.

Green Normal operation.

Amber Minor error.

Blinking

Amber

Critical error.

Beaconing Off Beaconing not enabled.

Blinking

blue 1 Hz

Beaconing to locate a selected blade—If the LED is not

blinking, the blade is not selected. You can initiate

beaconing in UCS Manager or with the button.

Activity

(Disk Drive)

Off Inactive.

Green Outstanding I/O to disk drive.

Flashing

Amber

4Hz

Rebuild in progress. Health LED will flash in unison.

Flashing

Amber

4hz

Identify drive active.

Health

(Disk Drive)

Off Can mean either no fault detected or the drive is not

installed.

Flashing

Amber

4hz

Identify drive active. If the Activity LED is also flashing

amber, a drive rebuild is in progress.

Amber Fault detected.

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

The beaconing function for an individual server may get turned on or off by pressing the combination

button and LED. See Table 1 for details.

The power button and LED allows you to manually take a server temporarily out of service but leave it

in a state where it can be restarted quickly. If the desired power state for a service profile associated with

a blade server or an integrated rack-mount server is set to "off", using the power button or Cisco UCS

Manager to reset the server will cause the desired power state of the server to become out of sync with

the actual power state and the server may unexpected shutdown at a later time. To safely reboot a server

from a power-down state, use the Boot Server action in Cisco UCS Manager.

Connectors

The console port allows a direct connection to a blade server to allow operating system installation and

other management tasks to be done directly rather than remotely. The port uses the KVM dongle cable

(N20-BKVM shown in Figure 2) which provides a connection into a Cisco UCS blade server; it has a a

DB9 serial connector, a VGA connector for a monitor, and dual USB ports for a keyboard and mouse.

With this cable, you can create a direct connection to the operating system and the BIOS running on a

blade server. A KVM cable ships standard with each blade chassis accessory kit.

Figure 2 KVM Cable for Blade Servers

Conventions

This document uses the following conventions for notes, cautions, and safety warnings.

Notes and Cautions contain important information that you should know.

Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered

in the publication.

Caution Means reader be careful. You are capable of doing something that might result in equipment damage or

loss of data.

1Connector to blade server slot 3VGA connection for a monitor

2DB9 serial connector 42-port USB connector for a mouse and keyboard

192621

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, can

cause physical injuries. A warning symbol precedes each warning statement.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Siebefinden sich in einer Situation, die zu Verletzungenführen

kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und

den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli

relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le

traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med

elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten

av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne

enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos

perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de

prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los

procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el

número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och

känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av

varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os

circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o

número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de

segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de

involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til

undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de

oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Installing and Removing a Blade Server Hard Drive

There are up to two front-accessible, hot-swappable, 2.5-inch drives per blade. An LSI SAS 2004 RAID

controller is embedded in the motherboard (it is not separately replaceable), and it supports RAID 0 and

1. You can remove blade server hard drives without removing the blade server from the chassis. All other

component replacements for a blade server requires removing the blade from the chassis. Unused hard

drive bays should always be covered with cover plates (N20-BBLKD) to ensure proper cooling and

ventilation. The chassis is omitted from illustrations here to simplify the drawing.

Caution To prevent ESD damage, wear grounding wrist straps during these procedures and handle modules by

the carrier edges only.

Caution RAID array migration between a B200 M1 or B200 M2 and a B200 M3 is not supported

Replacing an HDD or SSD with a drive of the same size, model, and manufacturer should not cause any

problems with UCS Manager. If the drive being replaced was part of a RAID array. we recommend using

a newly ordered drive of identical size, model, and manufacturer to replace the failed drive. We

recommend following industry standard practice of using drives of the same capacity when creating

Send document comments to [email protected]

Cisco UCS B200 M3 Blade Server Installation and Service Note

OL-26624-01

Installing and Removing a Blade Server Hard Drive

RAID volumes. If drives of different capacities are used, the useable portion of the smallest drive will

be used on all drives that make up the RAID volume. Before upgrading or adding an HDD to a running

system, check the service profile in UCS Manager to make sure that the new hardware configuration is

within the parameters allowed by the service profile.

Hard disk and RAID troubleshooting information is in the "Troubleshooting Server Hardware" chapter

of the Cisco UCS Troubleshooting Guide. This provides a procedure for moving a RAID array between

B200 M3 servers if needed.

Table 2 shows the drives supported in this blade server. They are all hot pluggable and come with the

drive sled attached. Spare drive sleds are not available.

Removing a Blade Server Hard Drive

To remove a hard drive from a blade server, follow these steps:

Step 1 Push the button to release the ejector, and then pull the hard drive from its slot.

Table 2 Supported Drives

Product ID Description

HDDs

A03-D1TBSATA 1 TB 6 Gb SATA 7.2K RPM SFF HDD

UCS-HDD900GI2F106 900GB 6Gb SAS 10K RPM SFF HDD

A03-D600GA2 600 GB 6 Gb SAS transfer rate, 10K RPM SFF HDD

A03-D500GC3 500GB 6Gb SATA 7.2K RPM SFF HDD

UCS-HDD300GI2F105 300 GB 6 Gb SAS transfer rate, 15K RPM SFF HDD

A03-D300GA2 300 GB 6Gb SAS 10K RPM SFF HDD

A03-D146GC2 146 GB 6 Gb SAS transfer rate, 15K RPM SFF HDD

SSDs

UCS-SD300G0KA2-E 300GB Std Height 15mm SATA SSD

UCS-SD200G0KA2-E 200 GB Std Height 15 mm SATA SSD

UCS-SD100G0KA2-E 100 GB Std Height 15 mm SATA SSD

Andere Handbücher für UCS B200 M3

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco Digital Media System 3.5 Bedienungsanleitung

Cisco

Cisco C880 Series Montageanleitung

Cisco

Cisco UCS C220 M4 Bedienungsanleitung

Cisco

Cisco UCS 5100 Bedienungsanleitung

Cisco

Cisco UCS B200 M3 Systemhandbuch

Cisco

Cisco UCS B Series Installations- und Betriebshandbuch

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco Content Delivery Engine CDE100 Handbuch

Cisco

Cisco TelePresence Server 7010 Referenzhandbuch

Cisco

Cisco UCS C210 Montage- und Wartungsanleitung

Cisco

Cisco ONS 15454 Series Bedienungsanleitung

Cisco

Cisco UCS C460 M2 Bedienungsanleitung

Cisco

Cisco UCS M3 Series Bedienungsanleitung

Cisco

Cisco UCS C220 M3 Bedienungsanleitung

Cisco

Cisco ASR 5000 Series Bedienungsanleitung

Cisco

Cisco Firepower Management Centers Bedienungsanleitung

Cisco

Cisco TelePresence Server 7010 Bedienungsanleitung

Cisco

Cisco UCS B200 M3 Handbuch

Cisco

Cisco C880 M5 Bedienungsanleitung

Cisco

Cisco ACE-4710-1F-K9 Bedienungsanleitung

Cisco

Cisco UCS B200 M3 Handbuch

Cisco

Cisco UCS C250 Montage- und Wartungsanleitung

Cisco

Cisco UCS C24 Montage- und Wartungsanleitung

Cisco

Cisco UCS B200 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung