Cisco UCS C460 M4 Bedienungsanleitung

Contents

Introduction

Requirements

Components Used

Background Information

Problem

Solution

Related Information

Introduction

This document describes an issue recognized with SAP HANA Scale-Out solutions with EMC VNC

storage attached which leads to an extended startup time of the Linux servers running the SAP

HANA application.

Requirements

Cisco recommends that you have a basic understanding of the preboot execution environment

(PXE) for a diskless environment and the standard Linux init boot process.

Components Used

The information in this document is based on these software and hardware versions:

SAP HANA Scale-Out solution with EMC VNX 5400 storage.

●

UCS C460-M4 and/or UCS B460-M4 servers

●

SUSE Linux Enterprise System 11.3

●

The information in this document was created from the devices in a specific lab environment. All of

the devices in this document started with a cleared (default) configuration following the solution

specific Cisco internal installation guidelines. If your solution is live, make sure that you

understand the potential impact of any command.

Background Information

The SAP HANA Scale-Out solutions are configured with two management servers to enable the

solution for the Preboot eXecution Environment (PXE) for diskless boot of the servers using a

network interface. The second management server exists for fault-tolerance reasons to avoid the

situation the servers cannot boot any longer in case of the first management server is not

available.

Note: Once the HANA server is up and running the management servers can be rebooted

without influencing the HANA servers.

The management server acts as DHCP and tftp server.

The EMC VNX storage acts as NFS server in this solution providing the nfsroot file system for

each server.

The boot process runs through the following steps:

The HANA server powers up including hardware self-checks.1. It sends a DHCP request via network interface eth0 (vlan 127) to the management server. 2. The management server provides the Server IP address and the tftp server IP address.3. In the next step it serves out the kernel and initrd from the tftpboot directory that is build at

installation time.

The HANA server loads the kernel and initrd from the tftpserver including all necessary

drivers available in initrd.

Once loaded the HANA server mounts the nfsroot volume via network interface eth0 (vlan

127).

Finally, the HANA server runs through the default Linux init process to complete the startup.7.

Problem

During the PXE boot process of the UCS servers the Linux init process stops for approximately 8

minutes when the network interfaces are activated. Afterwards the startup process continues

without any further issues.

When the HANA server runs through the default Linux init process it reads the network

configuration files as well and re-activates the network interfaces. The reason is the boot option

"onboot" is set to "yes" by default. This means the HANA server sends an additional DHCP

request to the management server and lose the file handler for the nfsroot volume at the same

time which stops the init process to continue.

There are no error messages visible on the console, but when you enter the boot options "debug

initcall_debug" you will notice the NFS server stops responding for approximately 8 minutes

sending "nfs: server 192.168.127.11 not responding, still trying" when reviewing the boot log

information.

Solution

Change the configuration file /etc/sysconfig/network/ifcfg-eth0 and add the option "ONBOOT='no'".

This is an example of the ifcfg-eth0 file:

Related Information

SUSE Documentation: "PXE Booting NFS or iSCSI Roots for a Diskless Environment"

SUSE Documentation: "SLES Administration - The Linux Boot Process"

Andere Handbücher für UCS C460 M4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Server Handbücher

Cisco

Cisco UCS 5100 Handbuch

Cisco

Cisco UCS B200 M3 Bedienungsanleitung

Cisco

Cisco UCS S3260 M5 Leitfaden

Cisco

Cisco Sourcefire Defense Center 750 Bedienungsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco Secure Network Server 3600 Series Handbuch

Cisco

Cisco UCS C240 Montage- und Wartungsanleitung

Cisco

Cisco C220 M3 Handbuch

Cisco

Cisco UCS C Series Montageanleitung

Cisco

Cisco AS5300-96VOIP-A Bedienungsanleitung

Cisco

Cisco CPS-UCS-2RU-K9 Bedienungsanleitung

Cisco

Cisco UCS B200 M4 Bedienungsanleitung

Cisco

Cisco SNS-3415 series Bedienungsanleitung

Cisco

Cisco UCS C420 Montage- und Wartungsanleitung

Cisco

Cisco SFS 7008P Bedienungs- und Wartungsanleitung

Cisco

Cisco Firepower 2100 Series Handbuch

Cisco

Cisco SCE8000 GBE Bedienerhandbuch

Cisco

Cisco Catalyst 6800 Bedienungsanleitung

Cisco

Cisco UCS B440-M1 Kurzanleitung

Cisco

Cisco PDS2000 Bedienungsanleitung

Cisco

Cisco UCS B460 M4 Bedienungsanleitung

Cisco

Cisco UCS C460 M4 Installations- und Betriebshandbuch

Cisco

Cisco TelePresence Bedienungsanleitung

Cisco

Cisco UCS C220 M5SX Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung