Clarke CES560 Bedienungsanleitung

USER INSTRUCTIONS

GC0315

ENGINE STAND

MODEL NO: CES560

PART NO: 7610123

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Engine Stand.

Before attempting to operate the product, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

TECHNICAL SPECIFICATIONS

Max Capacity (SWL) 560 kg (0.56 Tonne)

Net Weight 28 kg

Dimensions L x W x H 1000 x 845 x 810

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

SAFETY PRECAUTIONS

1. Do not allow personnel to use the stand unless they have read these safety

precautions.

2. Never tamper with the product or modify it in any way, as this could prove

to be dangerous and will invalidate the guarantee. Only use the product

for the purpose for which it is intended.

3. Ensure that the stand is in good working order. Have any damaged parts

repaired or replaced immediately. Use genuine Clarke parts only. The use

of unauthorised parts may be dangerous and invalidate the guarantee.

4. Do not use the stand if it is damaged.

5. Use the stand in a suitable, well lit work area.

6. Keep the work area clean and tidy and free from unrelated items.

7. Do not use the stand when you are tired or under the influence of alcohol,

drugs or intoxicating medication.

8. Use the stand on level and solid ground, preferably concrete. Avoid soft/

unmade ground as the castors may sink in.

9. Ensure all bystanders keep at a safe distance whilst the stand is in use.

10. Do not work underneath an engine mounted on the stand.

11. Never climb on, or attempt to ride on the stand.

12. Take care not to trap your fingers in the adjustable parts of the stand.

13. Due to the weight of the loaded stand, the help of an assistant will be

beneficial when moving the stand around.

14. Never attempt to move a loaded engine stand across a floor having

cracks, pebbles, or other obstacles which might impede its movement.

15. The components of this engine stand are designed to withstand the rated

capacity. Do not substitute any other components or exceed the rated

capacity of the stand.

16. To move a loaded stand, push it from the load side. DO NOT move the

stand from the handle end and never pull the stand towards yourself.

17. Always ensure the engine is properly bolted to the stand.

18. Do not over-reach. Keep your proper footing and balance at all times.

19. Safety equipment such as gloves and non-skid shoes will reduce personal

injuries.

20. Failure to heed these warnings may result in damage to the equipment, or

serious personal injury.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING & ASSEMBLY

Unpack the components on a clean flat area of hard standing, and ensure

that all parts are present according to the packing list, as follows:

Visually inspect all components to ensure that no damage was suffered in

transit. Any deficiencies should be reported to your CLARKE dealer

immediately.

TOOLS REQUIRED

• Open or ratchet ring spanner (19 mm) or an adjustable wrench.

1 1 x Column assembly 6 1 x Mounting plate

2 1 x Rear cross-member 7 1 x Mounting plate handle

3 2 x Side arms 8 4 x Mounting Arms

4 2 x Castors with brake 9 1 x Parts tray

5 2 x Wheels 10 1 x Fixings kit including nuts, bolts,

washers and locating pin.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

ASSEMBLY

IMPORTANT: Due to the weight of the components, we recommend that you

get assistance during assembly.

1. Loosely bolt the column to the

rear cross member.

2. Loosely bolt the side arms to the

rear cross member.

3. Bolt the straight castors to the

brackets on side arms.

4. Attach the castors to the side

arms, using the nuts, bolts &

washers.

5. Fit the mounting plate to the

upright column and secure with

the locating pin.

6. Attach the four mounting arms to

the mounting plate with nuts, bolts

and washers.

7. Pass the handle through the hole

in the spindle of the mounting

plate.

8. Ensure that all weight is spread

evenly across the crossmember

and side arms, making sure that

all four wheels are on level

ground and that the assembly is

sitting square and true. Tighten all

nuts and bolts.

9. Fit the parts tray to the column.

INSPECTION BEFORE USE

1. Always visually inspect the stand before use, to ensure that all parts are

correctly located and secure. Check for cracks, deformation or other signs

of damage or worn parts and check the castors for damage. Do not use

the stand unless it is totally sound.

2. Check castors to ensure they move freely without undue wear to their

pivots, and that the wheels are not cracked or damaged in any way.

3. Remove any rust or corrosion and repaint for protection.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MOUNTING THE ENGINE TO THE STAND

1. The mounting plate has four

adjustable arms with long bolt

holes. This is where the engine will

mount to the engine stand, using

suitable bolts which are

compatible with the threaded

holes in the engine block.

2. If the bellhousing bolts are too

short, obtain bolts that have the

same diameter and thread pitch.

Ideally, the bolts must be long

enough to go through the engine

stand arms and go at least one

inch into the engine block.

3. Lift the engine with your engine

hoist and move it towards the

engine stand.

4. Remove the locating pin, then

remove the mounting plate assembly from the engine stand.

5. Using compatible bolts, pass them through the mounting arms and bolt

them to the engine where the transmission was mounted to the block.

Mount two arms low down on the engine and bolt the other two as high as

possible.

6. Adjust the arms on the engine stand mounts so that the centre of the

mounting plate is aligned with the centre of the engine crankshaft. By

doing this you can ensure that the engine is balanced on the stand.

Tighten the bolts securely.

7. Lower the engine until the spindle is at the same level as the engine stand.

Slide the spindle of the mount into the engine stand. Replace the locating

pin to secure the mounting.

8. Slowly lower the engine hoist so that the engine stand starts to support the

weight of the engine. Double-check all fasteners and be sure that the

engine is secure.

9. Once you are confident that the stand is supporting the weight of the

engine, disconnect the hoist. Now that the engine is mounted to the stand

it can be rotated around to access all sides of the engine. Use the locking

pin to lock the engine at one of four different working angles.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

PARTS DIAGRAM

PART NO DESCRIPTION PART NO DESCRIPTION

1 Main Column assembly 11 Bolt (1/2” x 2.1/2”)

2 Side Arm 12 Flat Washer

3 Rear Crossmember 13 Hex Nut

4 Bolt (1/2” x 3.1/2”) 14 Parts Tray

5 Locking Washer 15 Rotation Handle

6 Hex Nut (1/2”) 16 Warning Label

7 Bolt 1/2” x 1” 17 Rear Wheel

8 Mounting Plate 18 Front Castor Wheel

9 Locating Pin 19 Bolt (5/16” x 5/16”)

10 Mounting Arm 20 Hex Nut

Inhaltsverzeichnis

Andere Clarke Rack & Stand Handbücher

Clarke

Clarke CSR4550BO Bedienungsanleitung

Clarke

Clarke MCD1 Bedienungsanleitung

Clarke

Clarke CMS1 Bedienungsanleitung

Clarke

Clarke CTA150 Bedienungsanleitung

Clarke

Clarke CGR1 Bedienungsanleitung

Clarke

Clarke CDS3 Bedienungsanleitung

Clarke

Clarke LB7S Bedienungsanleitung

Clarke

Clarke CT100PR Bedienungsanleitung

Clarke

Clarke CSP420 Bedienungsanleitung

Clarke

Clarke CWC80B Bedienungsanleitung

Clarke

Clarke CMSS Bedienungsanleitung

Clarke

Clarke CBS3 Bedienungsanleitung

Clarke

Clarke CARS1 Bedienungsanleitung

Clarke

Clarke MDS1 Bedienungsanleitung

Clarke

Clarke CRSF2 Bedienungsanleitung

Clarke

Clarke CAX6TBC Bedienungsanleitung

Clarke

Clarke CHT399 Bedienungsanleitung

Clarke

Clarke CUTS1 Bedienungsanleitung

Clarke

Clarke LB5S Bedienungsanleitung

Clarke

Clarke CMSSR Bedienungsanleitung

Clarke

Clarke CES680F Betriebsanleitung

Clarke

Clarke Strong-Arm CES450 Bedienungsanleitung

Clarke

Clarke CAX3TBC Bedienungsanleitung

Clarke

Clarke CAX20S Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung