Clarke CDS3 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

GC09/13

DRILL STAND WITH VICE

Model No: CDS3

Part No: 6500224

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE product.

Please read and follow the instructions carefully. In doing so you will ensure

the safety of yourself and others around you, and you can look forward to

the product giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose. Faulty goods

should be returned to their place of purchase. No product can be returned

to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATION

erutaeF noisnemiD

htpeDgnillirDmumixaMmm06

thgieHnmuloCmm005

thgieWgk83.3

)HxWxD(snoisnemiDmm894x061x253

seziSralloCllirDmm34/83

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

COMPONENT PARTS

The component parts of your CDS3 drill stand are shown in fig 1.

• Any electric drill with a standard 43mm diameter neck may be fitted

directly to the head assembly.

• A reducing sleeve is provided, allowing a drill with a 38mm diameter neck

also to be accommodated.

• The depth of travel of the drill may be controlled by using the depth

adjuster. A depth scale is provided so that accurate drilling depths may

be set.

OPERATING LEVER

MOUNTING HOLE

VICE JAW QUICK

RELEASE

DEPTH ADJUSTER

ROD

DRILL LOCKING COLLAR

WITH REDUCING SLEEVE

LOWER COLLAR

DEPTH SCALE

COLUMN

HEAD ASSEMBLY

CONNECTING ARM

FIG 1

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

ASSEMBLY

1. Insert the column into the base

and secure with the bolt using a

14mm wrench.

• Ensure the column does not

project below the base.

2. Slide the lower collar onto the

column and secure

approximately half way up the

column using the hex key.

3. Slide the head assembly onto the

column.

4. Attach the operating lever to

both the head assembly and to

the connecting arm using the

nut/bolt at one end, using a

10mm wrench and tighten the

hex key loosely at the other end.

5. Always store the hex key in the

clips on the side of the head

assembly.

Fig 2

Column level

with base

Fig 3

Operating Lever

Head

Assembly

Connecting

Arm

Fig 4

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

6. Secure the vice to the base using

two suitable bolts with nuts and

washers (not supplied).

• To position the vice relative to

the column, slacken the two

vice securing bolts and

manoeuvre the vice as

required.

IMPORTANT!

Secure the base to a workbench or sturdy table using suitable bolts (not

supplied). Drill the work-bench/table accordingly, using the four mounting

holes in the stand base as a template.

FITTING A DRILL

1. Fit an electric drill with a

standard 43mm diameter neck to

the head assembly and secure in

the locking collar as shown in Fig

6. Tighten the locking collar using

the hex key.

2. If using a drill with a 38mm neck,

fit the reducing sleeve provided

into the locking collar before

inserting the drill.

SETTING THE DEPTH

1. Decide on the depth of hole

required to be drilled.

2. Release the hex head bolt which

locks the depth adjusting rod.

3. Using the operating arm, lower

the drill until the required reading

is showing on the scale and lock

the depth adjuster rod at this

position using the hex key.

4. It is recommended that a light

smearing of lubricant be applied to the column to assist with free

movement.

Fig 5

Bolt/nut

Fig 6

Hex bolt in

locking collar

Fig 7

Depth

Scale

Depth

Adjusting

Rod

Hex head

bolt

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

DRILLING THE HOLE

1. Lower the head assembly until

the drill bit is just touching the

workpiece as in Fig 8, and set the

head assembly in position using

the hex key shown in Fig 3.

2. Switch the drill on, and press

down on the operating lever as

the drill bit starts drilling. The

depth of hole will be restricted by

the depth stop.

ADJUSTING THE VICE

1. A quick setting button is provided

for the vice jaw adjustment. Press

the red button whilst pushing IN or

pulling OUT the handle.

Fig 8

Fig 9

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

NOTES

__________________________________________________________________________

Inhaltsverzeichnis

Andere Clarke Rack & Stand Handbücher

Clarke

Clarke CAX3TA Bedienungsanleitung

Clarke

Clarke CAX3TAB Bedienungsanleitung

Clarke

Clarke CWMWR1 Bedienungsanleitung

Clarke

Clarke CWR45 Programmierhandbuch

Clarke

Clarke CSM5175 Series Bedienungsanleitung

Clarke

Clarke CSP420 Bedienungsanleitung

Clarke

Clarke CAX6TBC Bedienungsanleitung

Clarke

Clarke MCD1 Bedienungsanleitung

Clarke

Clarke CAX20S Bedienungsanleitung

Clarke

Clarke STRONG-ARM CAX3TPB Bedienungsanleitung

Clarke

Clarke CRSF2 Bedienungsanleitung

Clarke

Clarke CGR1 Bedienungsanleitung

Clarke

Clarke CMSS Bedienungsanleitung

Clarke

Clarke Strong-Arm CES340 Bedienungsanleitung

Clarke

Clarke CBS3 Bedienungsanleitung

Clarke

Clarke CWR1 Bedienungsanleitung

Clarke

Clarke CWC80B Bedienungsanleitung

Clarke

Clarke CARS1 Bedienungsanleitung

Clarke

Clarke CHT399 Bedienungsanleitung

Clarke

Clarke CT100PR Bedienungsanleitung

Clarke

Clarke LB5S Bedienungsanleitung

Clarke

Clarke CMSSR Bedienungsanleitung

Clarke

Clarke CES680F Betriebsanleitung

Clarke

Clarke CTA150 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung