Clarke CES680F Betriebsanleitung

ASSEMBLY & USER INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0918 Issue 2

FOLDING ENGINE STAND

MODEL NO: CES680F

PART NO: 7610122

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Engine Stand.

Before attempting to operate the product, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the stand giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

TECHNICAL SPECIFICATIONS

SAFETY PRECAUTIONS

1. Do not allow personnel to use the stand unless they have read these safety

precautions.

2. Never tamper with the product or modify it in any way, as this could prove

to be dangerous and will invalidate the guarantee. Only use the product

for the purpose for which it is intended.

3. Ensure that the stand is in good working order. Have any damaged parts

repaired or replaced immediately. Use genuine Clarke parts only. The use

of unauthorised parts may be dangerous and invalidate the guarantee.

Max Capacity (SWL) 680 kg (0.68 Tonne)

Net Weight 33 kg

Dimensions L x W x H 800 x 830 x 900 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

4. Do not use the stand if it is damaged.

5. Use the stand in a suitable, well lit work area.

6. Keep the work area clean and tidy and free from unrelated items.

7. Do not use the stand when you are tired or under the influence of alcohol,

drugs or intoxicating medication.

8. Use the stand on level and solid ground, preferably concrete. Avoid soft/

unmade ground as the castors may sink in.

9. Ensure all bystanders keep at a safe distance whilst the stand is in use.

10. Do not work underneath an engine mounted on the stand.

11. Never climb on, or attempt to ride on the stand.

12. Take care not to trap your fingers in the adjustable parts of the stand.

13. Due to the weight of the loaded stand, the help of an assistant will be

beneficial when moving the stand around.

14. Never attempt to move a loaded engine stand across a floor having

cracks, pebbles, or other obstacles which might impede its movement.

15. The components of this engine stand are designed to withstand the rated

capacity. Do not substitute any other components or exceed the rated

capacity of the stand.

16. To move a loaded stand, push it from the load side. DO NOT move the

stand from the handle end and never pull the stand towards yourself.

17. Always ensure the engine is properly bolted to the stand.

18. Do not over-reach. Keep your proper footing and balance at all times.

19. Safety equipment such as gloves and non-skid shoes will reduce personal

injuries.

20. Failure to heed these warnings may result in damage to the equipment, or

serious personal injury.

INSPECTION BEFORE USE

1. Always visually inspect the stand before use, to ensure that all parts are

correctly located and secure. Check for cracks, deformation or other signs

of damage or worn parts and check the castors for damage. Do not use

the stand unless it is totally sound.

2. Check castors to ensure they move freely without undue wear to their

pivots, and that the wheels are not cracked or damaged in any way.

3. Remove any rust or corrosion and repaint for protection.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

UNPACKING & ASSEMBLY

Unpack the components on a clean flat area of hard standing, and ensure

that all parts are present according to the packing list, as follows:

Visually inspect all components to ensure that no damage was suffered in

transit. Any deficiencies should be reported to your CLARKE dealer

immediately.

TOOLS REQUIRED

Open or ratchet ring spanners (19 mm) or an adjustable wrench.

1 1 x Supporting column 6 2 x Front wheel

2 1 x Rear crossmember 7 1 x Middle castor

3 1 x Front crossmember 8 1 x Engine mounting plate

4 1 x Hinged centre spine 9 1 x Mounting control handle

5 2 x Rear castor with brake 10 4 x Engine mounting arms

1 x Fixings kit including nuts,

bolts, washers and locating pin

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

1. Loosely bolt the supporting

column to the rear crossmember.

2. Loosely bolt the centre spine to

the front crossmember.

3. Secure the braked castors to the

front crossmember with nuts and

washers.

4. Fit the wheels to the rear cross-

member using the small washers

and split-pins.

5. Fit the middle castor to the

supporting column and secure

with washers and nut.

6. Connect the hinged centre spine

to the column support section

using the pivot bolt, washers &

nut. Insert the locking pin and R-

clip through the holes in the spine/

supporting column according to

whether the engine stand is to be

in use, or folded for storage.

7. Fit the engine mounting plate to

the column and secure with the

locating pin.

8. Loosely attach the four mounting

arms to the engine mounting

plate with nuts, bolts and washers.

9. Fit the handle through the hole in

the spindle of the mounting plate.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Servi[email protected]

10. Ensure that all weight is spread evenly across all sections, making sure that

all wheels/castors are on level ground and that the assembly is sitting

square and true. Tighten all nuts and bolts.

11. Store the operating handle in the socket provided when not in use.

MOUNTING THE ENGINE TO THE STAND

1. The mounting plate has four

adjustable arms with long bolt

holes. This is where the engine will

mount to the engine stand, using

suitable bolts which are

compatible with threaded holes

in the engine block.

2. If the bellhousing bolts are too

short, obtain bolts that have the

same diameter and thread pitch.

Ideally, the bolts must be long

enough to go through the engine

mounting arms and go at least

one inch into the engine block.

3. Lift the engine with your engine

hoist and move it towards the

engine stand.

4. Remove the locating pin, then

remove the mounting plate

assembly from the engine stand.

5. Using compatible bolts, pass them

through the mounting arms and bolt them to the engine where the

transmission was mounted to the block. Mount two arms low down on the

engine and bolt the other two as high as possible.

6. Adjust the arms on the engine stand mounts so that the centre of the

mounting plate is aligned with the centre of the engine crankshaft. By

doing this you can ensure that the engine is balanced on the stand.

Tighten the bolts securely.

7. Lower the engine until the spindle is at the same level as the engine stand.

Slide the spindle of the mounting plate into the engine stand. Replace the

locating pin to secure the mounting.

8. Slowly lower the engine so that the engine stand starts to support the

weight of the engine. Double-check all fasteners and be sure that the

engine is secure.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

9. Once you are confident that the stand is supporting the weight of the

engine, disconnect the hoist. Now that the engine is mounted to the stand

it can be rotated around to access all sides of the engine. Use the locking

pin to lock the engine at one of four different working angles.

PARTS DIAGRAM

PART NO DESCRIPTION PART NO DESCRIPTION

1 Supporting Column 12 Lock Washer

2 Rear Crossmember 13 Flat Washer

3 Front Crossmember 14 Hex Nut

4 Hinged Centre Spine 15 Bolt (110mm)

5 Castor (with brake) 16 Washer

6 Front Wheel 17 Split Pin

7 Engine Mounting Plate 18 R-Clip

8 Engine Mounting Arm 19 Mounting Control Handle

9 Locating Pin 20 Securing Chain

10 Spine Locking Pin 21 Bolt (60mm)

11 Bolt (80mm) 22 Middle Castor

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Rack & Stand Handbücher

Clarke

Clarke Strong-Arm CES680 Betriebsanleitung

Clarke

Clarke Strong-Arm CES340 Bedienungsanleitung

Clarke

Clarke CT100PR Bedienungsanleitung

Clarke

Clarke CTS4000B Bedienungsanleitung

Clarke

Clarke CHT399 Bedienungsanleitung

Clarke

Clarke CUTS1 Bedienungsanleitung

Clarke

Clarke CAX20S Bedienungsanleitung

Clarke

Clarke CSM5175 Series Bedienungsanleitung

Clarke

Clarke CDS3 Bedienungsanleitung

Clarke

Clarke CSM4200 Bedienungsanleitung

Clarke

Clarke CMSS Bedienungsanleitung

Clarke

Clarke CWMWR1 Bedienungsanleitung

Clarke

Clarke CWR45B Programmierhandbuch

Clarke

Clarke CAX3TA Bedienungsanleitung

Clarke

Clarke CES560 Bedienungsanleitung

Clarke

Clarke Strong-Arm CES450 Bedienungsanleitung

Clarke

Clarke CSR4550BO Bedienungsanleitung

Clarke

Clarke STRONG-ARM CAX3TPB Bedienungsanleitung

Clarke

Clarke CARS1 Bedienungsanleitung

Clarke

Clarke CMS1 Bedienungsanleitung

Clarke

Clarke CWR1 Bedienungsanleitung

Clarke

Clarke CWR45 Programmierhandbuch

Clarke

Clarke CAX6TBC Bedienungsanleitung

Clarke

Clarke MCD1 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung