Clarke CTS4000B Bedienungsanleitung

INSTRUCTIONS

GC0220 - ISS 4

AUTOMOTIVE SUPPORT STAND

MODEL NO: CTS4000B

PART NO: 7600200

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS - ALWAYS READ BEFORE USE

1. Read these instructions carefully before use.

2. ALWAYS inspect before each use, to ensure the frame is not bent or twisted

and that there are no cracked welds etc. Should any damage be

apparent, or if the stand has been subjected to an abnormal shock, it

should be removed from service and repaired by a qualified technician.

3. DO NOT use this tool as a jack.

4. DO NOT use this stand to support a vehicle transmission.

5. Do not exceed the stand’s maximum load (750kg).

6. Use only as specified in this manual.

7. NEVER let children play around the stand.

8. Replace the safety warning label if it becomes unreadable.

9. For your safety, do not modify this stand in any way.

USING THE SUPPORT STAND

This Support Stand is designed for many support uses e.g. exhausts, and

requires assembling according to the drawing opposite.

1. Rotate the Screw Nut (3), anticlockwise, using the handles (10), to lower the

Saddle (1), as far as possible.

2. Grasp one of the handles (10), and taking the weight of the complete

Upper Assembly Saddle, Screw Rod (2), Screw Nut, Handles and Tube Insert

(5), remove the Locking Pin (11), which secures the Upper Assembly to the

Support Post (7).

3. Raise the Upper Assembly as high as necessary so that the Saddle is as near

as possible to the load.

WARNING: BEFORE USE, MAKE SURE THAT THERE IS NO DAMAGE TO ANY

PART OF THE STAND. IF THERE IS, DO NOT USE.

WARNING: IT MUST BE ENSURED THAT THE LOAD IS CAREFULLY LOCATED

ONTO THE CENTRE OF THE STAND SADDLE. FAILURE TO DO THIS CAN

RESULT IN DAMAGE TO THE STAND, LOSS OF SUPPORT TO THE LOAD,

SERIOUS PERSONAL INJURY OR LOSS OF LIFE.

WARNING: DO NOT EXCEED THE RATED LOAD.

WARNING: USE ONLY ON A HARD, FLAT SURFACE, E.G. CONCRETE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

4. Line up one of the holes in the Tube Insert (5) with the hole in the top of the

Support Post and locate using the Locking Pin.

5. Finally, screw the Screw Nut clockwise so that the Saddle contacts the load

at a suitable support point...careless positioning could result in damage to

the load. Continue to raise the saddle, but only enough to take the weight

of the load.

MAINTENANCE

The screw thread should be

greased occasionally with a

medium grease. In addition

to a visual inspection before

each use, the stand should

be inspected by a qualified

technician annually to

ensure it is completely safe

for use, with no distortion or

damage of any kind.

Ref No Description

1Saddle

2ScrewRod

3 Screw Nut

4 Bearing

5 Tube Insert

6 Bolt M10 x 25

7 Support Post

8Leg

9LowerStrut

10 Handle

11 Locking Pin

12 Bolt M10 x 20

13 Nut M10

14 Flat Washer

15 Connecting Plate

16 Upper Strut

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

SPECIFICATION

DECLARATION OF CONFORMITY

Maximum Height 2360 mm

Minimum Height 1255 mm

Maximum Load 750 kg

Product Weight 22 kg

Base dimensions 650 x 563 mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Rack & Stand Handbücher

Clarke

Clarke CGR1 Bedienungsanleitung

Clarke

Clarke MDS1 Bedienungsanleitung

Clarke

Clarke CTA150 Bedienungsanleitung

Clarke

Clarke CSR4200 Bedienungsanleitung

Clarke

Clarke CAX3TBC Bedienungsanleitung

Clarke

Clarke CWR45 Programmierhandbuch

Clarke

Clarke LB7S Bedienungsanleitung

Clarke

Clarke CWR45B Programmierhandbuch

Clarke

Clarke CAX20S Bedienungsanleitung

Clarke

Clarke Strong-Arm CES680 Betriebsanleitung

Clarke

Clarke CARS1 Bedienungsanleitung

Clarke

Clarke CBS3 Bedienungsanleitung

Clarke

Clarke Strong-Arm CES450 Bedienungsanleitung

Clarke

Clarke Metalworker CL430 Bedienungsanleitung

Clarke

Clarke CDS3 Bedienungsanleitung

Clarke

Clarke CAX3TAB Bedienungsanleitung

Clarke

Clarke CWC80B Bedienungsanleitung

Clarke

Clarke CAX3TA Bedienungsanleitung

Clarke

Clarke CSP420 Bedienungsanleitung

Clarke

Clarke CT100PR Bedienungsanleitung

Clarke

Clarke CSM5175 Series Bedienungsanleitung

Clarke

Clarke CES560 Bedienungsanleitung

Clarke

Clarke CHT399 Bedienungsanleitung

Clarke

Clarke CWMWR1 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung