Clarke CSR4200 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

GC0416

5-SHELF BOLTLESS SHELVING UNITS

MODEL NO: CSR4200

PART NO: SEE TABLE PAGE 2

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Shelving Unit.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

SCOPE

These instructions cover the following models

SPECIFICATIONS

Description Model Part Number

4-Shelf 200kg Boltless Shelving (Light Grey) CSR4200/40LG 6600710

4-Shelf 200kg Boltless Shelving (Blue) CSR4200/40BL 6600712

4-Shelf 200kg Boltless Shelving (Red) CSR4200/40RP 6600714

Model Dimensions

(W x D x H)

Weight

(Empty)

Load per

shelf (evenly

distributed)

All CRS4200 Units 900 x 400 x 1800 mm 14.2kg 200 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INVENTORY

No Description Quantity

APost 8

B Shelf 4

CLongBeam 8

DShortBeam 8

ESupportBeam 4

F Post Joining Insert 4

G Plastic End Cap 8

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY ADVICE

1. Assemble on a strong, level surface. Avoid assembly on a domestic carpet.

2. Use a cloth or softwood block to protect the surface finish of the product

when using a mallet. Strike the flat surface of each beam to prevent

damage to the beam.

3. Always ensure that the tabs enter fully into the slots.

4. It is recommended that the assembly should be done by two persons.

5. Always wear protective gloves when assembling the shelving unit.

6. The shelving unit is not recommended for outdoor use.

ASSEMBLY INSTRUCTIONS

TOOLS REQUIRED

• Rubber mallet or hammer

• Protective cloth/wood block

The tabs of the beams will often enter

the slots fully using just firm hand

pressure but if they are too tight, you

may require a rubber mallet to assist.

If so, always use a cloth to protect

the product paint finish.

Tap gently with the mallet to drive the

tabs of the beams fully into the slots in

the post. Always strike the edge close

to the post.

1. Use the short beams (D) to

connect the front and rear posts

(A) together.

NOTE: The short and long beams

should be installed with the

recessed edge uppermost to

retain the shelf.

• Repeat this again to create the

other end assembly, making sure

that the corresponding beams

are at the same height.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Ensure the tabs lie flat against the

surface of the post.

3. Join the two end assemblies

together with the long beams (C).

4. Connect the support beams (E) to

the long beams (C). First bend the

flexible tabs to 90 degrees to pass

them through the slotsin the long

beams.

• The tab initially pays flat against

the long beam (C).

5. Next, bend the tab back through

180 degrees to grip the long

beam.

• Use a screwdriver or similar tool to

bend the tabs.

6. Finally bend the tab again through

90 degrees the opposite way, to

seat tightly against the support

beam (E).

7. . Ensure there is no movement

between the beams.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

8. Fit post joining inserts (F) into the

posts (A), ensuring that the inserts

are fitted with their tabs to match

the slots of the posts.

9. Construct more upper end

assemblies onto the post inserts (F)

before adding more long beams

and support beams as previously

to complete the framework.

10. Lay the shelf panels (B) into

position.

• Always assemble the top shelf at

the highest possible position.

11. Fit the plastic end caps (G) to the

end of each post (A).

We recommend that the shelving be

secured to an adjacent wall using

typical wall insert plugs and screws

(not supplied) aligned with the slots in

the posts.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. Always maintain shelving in good condition for the best/safest

performance.

2. Never exceed the maximum load for these shelving units as stated in the

specification.

3. Never use these shelving units if they are damaged.

4. Always load small, stable items on the top shelves, heavier and bulky items

should be stored on the lower shelves.

5. Always distribute heavy loads evenly across the shelves.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of old products or damaged parts with general household

waste. All tools, accessories and packaging no longer required should be

sorted, taken to a recycling centre and disposed of appropriately.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Rack & Stand Handbücher

Clarke

Clarke CWMWR1 Bedienungsanleitung

Clarke

Clarke CRSF2 Bedienungsanleitung

Clarke

Clarke CT100PR Bedienungsanleitung

Clarke

Clarke CAX3TA Bedienungsanleitung

Clarke

Clarke CWC80B Bedienungsanleitung

Clarke

Clarke CSP420 Bedienungsanleitung

Clarke

Clarke LB7S Bedienungsanleitung

Clarke

Clarke CWR45B Programmierhandbuch

Clarke

Clarke CWR1 Bedienungsanleitung

Clarke

Clarke CSM5175 Series Bedienungsanleitung

Clarke

Clarke CES560 Bedienungsanleitung

Clarke

Clarke CWR45 Programmierhandbuch

Clarke

Clarke CARS1 Bedienungsanleitung

Clarke

Clarke STRONG-ARM CAX3TPB Bedienungsanleitung

Clarke

Clarke CAX20S Bedienungsanleitung

Clarke

Clarke CMSS Bedienungsanleitung

Clarke

Clarke CAX6TBC Bedienungsanleitung

Clarke

Clarke CHT399 Bedienungsanleitung

Clarke

Clarke CGR1 Bedienungsanleitung

Clarke

Clarke CSM4200 Bedienungsanleitung

Clarke

Clarke CAX3TAB Bedienungsanleitung

Clarke

Clarke CTS4000B Bedienungsanleitung

Clarke

Clarke MCD1 Bedienungsanleitung

Clarke

Clarke Metalworker CL430 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung