Clarke STRONG-ARM CAX3TPB Bedienungsanleitung

USER INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1121

3 TONNE AXLE STAND

MODEL NO: CAX3TPB

PART NO: 7600066

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS - ALWAYS READ BEFORE USE

• Read these instructions carefully before use.

• DO NOT exceed the axle stands maximum

load (1.5 tonne each/ 3 tonnes per pair), The

vehicle weight will be in the owners manual.

• Use only as specified in this manual.

• NEVER let children play in or around a vehicle

that is on axle stands.

• ALWAYS make sure that before you work

below the vehicle, a responsible person is

aware in case of injury or accident.

• DO NOT use more than one pair of axle

stands.

• Replace the warning label if it becomes

unreadable.

• Use only on a hard, flat surface for example

concrete.

• Make sure that you chock all the wheels that

remain on the ground.

• Make sure that the supported vehicle cannot

move.

• Set each axle stand below an appropriate

point on the vehicle - See your vehicle

owners manual for advice.

• Take care when using the axle stands on a

three-wheeled vehicle or trailer.

• Upper and lower columns are to be used as a

pair as supplied.

• Use stands as a matched pair to support one end of a vehicle only.

• For your safety, DO NOT modify these axle stands.

WARNING: USE ONLY ON A HARD, FLAT SURFACE FOR EXAMPLE

CONCRETE.

WARNING: NEVER WORK UNDER A VEHICLE SUPPORTED ONLY BY A JACK.

WARNING: AFTER LIFTING THE VEHICLE, SUPPORT IMMEDIATELY WITH

PROPERLY RATED AXLE STANDS

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

USING THE AXLE STANDS

1. Refer to the vehicle handbook for

the correct jacking procedure and

location of the support points.

ADJUSTING THE AXLE STAND

1. Remove the locating pin (if fitted).

2. Raise the upper column to the

required height and fit the locating

pin into the lowest hole visible.

3. Insert the retaining R-clip into the

end of the locating pin to secure in

position.

4. Position the axle stand under a

suitable supporting point. See your

vehicle manual for the location.

LOWERING THE VEHICLE

1. Slowly lower the vehicle onto the

centre of the saddle.

REMOVING THE AXLE STANDS

1. Raise the vehicle clear of the axle stands and remove the stands.

WARNING: BEFORE USE, MAKE SURE THAT THERE IS NO DAMAGE TO ANY

PART OF THE AXLE STAND, IF THERE IS, DO NOT USE THE AXLE STAND.

WARNING: IT MUST BE ENSURED THAT THE VEHICLE/LOAD IS CAREFULLY

LOCATED ONTO THE CENTRE OF THE AXLE STAND SADDLE. FAILURE TO DO

THIS CAN RESULT IN DAMAGE TO THE AXLE STANDS, LOSS OF SUPPORT TO

THE LOAD, SERIOUS PERSONAL INJURY OR LOSS OF LIFE.

WARNING: DO NOT EXCEED THE RATED LOAD OF 3 TONNES (PER PAIR).

WARNING: USE ONLY ON A HARD, FLAT SURFACE, E.G. CONCRETE.

WARNING: DO NOT LOAD THE STANDS OFF CENTRE. FAILURE TO HEED THIS

WARNING MAY CAUSE DAMAGE, INJURY OR LOSS OF LIFE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Ensure that all tools, equipment and personnel are clear before carefully

lowering the vehicle to the ground.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights

SPECIFICATION

Maximum Height 490 mm

Minimum Height 300 mm

Maximum Load 3 Tonnes per pair

Product Weight 5 kg (pair)

Number of Height Positions 5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Rack & Stand Handbücher

Clarke

Clarke CTS4000B Bedienungsanleitung

Clarke

Clarke CWC80B Bedienungsanleitung

Clarke

Clarke CWMWR1 Bedienungsanleitung

Clarke

Clarke CAX3TBC Bedienungsanleitung

Clarke

Clarke CDS3 Bedienungsanleitung

Clarke

Clarke CUTS1 Bedienungsanleitung

Clarke

Clarke CGR1 Bedienungsanleitung

Clarke

Clarke CRSF2 Bedienungsanleitung

Clarke

Clarke CSP420 Bedienungsanleitung

Clarke

Clarke Strong-Arm CES450 Bedienungsanleitung

Clarke

Clarke CMS1 Bedienungsanleitung

Clarke

Clarke LB7S Bedienungsanleitung

Clarke

Clarke Metalworker CL430 Bedienungsanleitung

Clarke

Clarke Strong-Arm CES340 Bedienungsanleitung

Clarke

Clarke CSM4200 Bedienungsanleitung

Clarke

Clarke CSM5175 Series Bedienungsanleitung

Clarke

Clarke CMSS Bedienungsanleitung

Clarke

Clarke CAX3TA Bedienungsanleitung

Clarke

Clarke CBS3 Bedienungsanleitung

Clarke

Clarke CAX6TBC Bedienungsanleitung

Clarke

Clarke CWR1 Bedienungsanleitung

Clarke

Clarke CWR45 Programmierhandbuch

Clarke

Clarke CSR4200 Bedienungsanleitung

Clarke

Clarke MCD1 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung