Clarke HSEC651A Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0218 ISS 1

ORIGINAL INSTRUCTIONS

SUBMERSIBLE SEWAGE CUTTER PUMP

MODEL NO: HSEC650A/651A/1400A

PART NO: 7230290, 7230295, 7230243

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Submersible Sewage Cutter Pump.

The pump is fitted with a tungsten carbide cutter, and is especially suited for

heavily polluted water containing waste solids, such as sewage, light slurry

etc.

This pump is NOT designed for pumping heavy slurry, sludge, mud, salt water,

or any water containing chemicals or other acidic contaminants. It is also not

suitable for single chamber septic tanks.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INSTRUCTIONS

GENERAL

1. Read all instructions before use

and save these instructions for

future use.

2. An approved residual current

device (RCD) which has a

tripping current of less then 30mA

MUST be used for all operations.

3. The electrical supply must be the

same as that on the rating plate.

4. Always make sure that your

hands are dry when connecting

or disconnecting from the mains

supply.

5. Never pull the mains lead to

disconnect the pump from the

mains socket.

6. The mains plug must be kept

away from the water at all times.

7. Do not allow children or

unauthorised people to touch the

pump, cables or connections.

8. Disconnect the pump from the

mains supply when not in use.

9. If necessary have the pump

repaired by a qualified person.

10. Keep the mains lead away from

heat, oil and sharp edges.

11. If you have to use an extension

lead with this product, it must be

designed for outdoor use and

incorporate a cable suitable for

use with Class I appliances.

12. Disconnect the pump from the

electrical supply and wear gloves

during servicing or maintenance.

PUMP SPECIFIC

1. Do not pump explosive /

flammable liquids or chemicals.

2. Never allow the pump to run dry

or operate out of the water.

3. Submersible pumps should always

be submerged and stored

vertically.

4. Disconnect the pump from the

mains supply before placing it

into or removing it from the water.

5. Always check the plug, and all

cables for damage before use.

6. Do not use the pump if

damaged. Refer to qualified

service personnel for repair.

7. Never carry or lower the pump by

the power cable or float switch

always use the handle or a rope

tied securely to the handle.

8. Never insert your fingers into the

pump whilst it is connected to the

mains.

9. Never use the submersible pump

in a swimming pool when there

are people or animals in the pool.

10. Keep the pump clear of any

sediment by standing it on a

platform or brick or suspending it

at a suitable depth.

11. Do not use the pump if the water

is liable to freeze, as this can

cause damage to the pump.

Remove the pump from the

water and store it in a frost free

location.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

We recommend that these pumps MUST be fitted with a Residual Current

Device (RCD), with a rated residual operating current of no greater than

30mA. This is mandatory when pump is used for pumping swimming pools

HSEC1400A + HSEC650A should have their mains lead connected to a

standard 230 volt (50Hz) electrical supply through an approved plug or a

suitably fused isolator switch.

As the colours of the flexible cable of this appliance may not correspond with

the coloured markings identifying terminals in your plug proceed as follows:

• The BLUE wire must be

connected to the

terminal which is

marked N or coloured

black.

• The BROWN wire must

be connected to the

terminal which is

marked L or coloured

red.

• The YELLOW AND

GREEN wire must be

connected to the terminal which is marked E or or coloured green.

HSEC651A must be connected to a protected 110V supply, through a

suitably approved connector. On no account must a 230V, 13amp plug be

used.

NOTE: If a portable 110V transformer is used, make sure it has a rated

capacity sufficient to take the load of the pump.

In the event that the pump is hard-wired into the electrical system, it must be

carried out in accordance with IEE regulations.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

USING THE PUMP

1. Using the adaptor if required,

connect a suitable hose (not

supplied) to the pump outlet.

• Suitable hoses are available from

your local Clarke dealer.

2. Place the pump vertically on a flat

surface in the area that you want to

drain.

• If there is sediment in the area,

place the pump on house bricks,

or similar.

• Ensure the pump is positioned with adequate space so that the

movement of the float switch is not restricted - recommended minimum

area of 50 x 50 cm.

• ALWAYS raise and lower the pump using a rope attached to the lifting

handle.

• Take all necessary precautions as described on page 3.

• The pump inlet must be fully submerged before the pump is switched on.

3. Connect the mains plug to a high sensitivity residual current device (RCD)

which has a tripping current of less then 30mA.

4. Switch the mains power supply on.

• The pump will begin to drain water.

• As the water level falls, so will the float switch, until it stops the pump.

WARNING: CHECK THE PUMP FOR DAMAGE BEFORE USE, DO NOT USE THE

PUMP IF IT IS DAMAGED IN ANY WAY.

WARNING: THE WATER BEING PUMPED WILL BE POLLUTED IF THIS PUMP

BECOMES DAMAGED AND LUBRICANT WITHIN THE PUMP ESCAPES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• You can adjust the position at

which the float switch lead is

held to the pump. Adjusting

the length of the float switch

lead will change the depth of

water at which the pump will

turn on or off.

5. When the pumping is finished,

disconnect the pump from the

mains power supply.

OVERLOAD SWITCH

These pumps are fitted with a thermal overload switch. If the pump overheats

for any reason, it will automatically switch the pump OFF. Once the pump has

cooled (at least 5-10 minutes), it will automatically restart.

CAUTION: DO NOT ALLOW THE PUMP TO RUN DRY

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

This pump should require no maintenance other than regular cleaning.

If the pump starts to show signs of wear or damage, contact your CLARKE

dealer for advice.

CLEANING

1. Check the pump installation regularly to ensure the water inlet is clear of

leaves or other debris.

2. Take extra care to remove any debris from around the impeller.

NOTE: Do not attempt to repair the pump yourself. Repairs must be carried

out by your CLARKE dealer, or contact the CLARKE Service

Department.

STORAGE

When the pump is not being used for extended periods, clean and dry it

thoroughly and store it indoors. If the pump is left in water, it must be run at

least once a week to prevent it from seizing up.

SPECIFICATIONS

WARNING: BEFORE CHECKING THE CONDITION OF THE PUMP, ENSURE IT

IS UNPLUGGED FROM THE MAINS SUPPLY. IF THE UNIT IS HARD WIRED,

ENSURE THE CIRCUIT BREAKER IS OPEN.

HSEC650A HSEC651A HSEC1400A

Part Number 7230290 7230295 7230243

Outlet Diameter 2“BSP (inc 2”BSP to 50 mm Hose Adaptor)

Voltage 230V/50hz 110V/50Hz* 230V~50Hz

Motor Wattage@ max flowrate 665W 665W 1400 W

Fuse Rating (amps) 13 13

Cable length (m) 10 10 10

IP Rating IP68 IP68 IP68

Max. Head (m) 9.5m 9.5m 13 m

Dimensions (D x W x H) mm 240 x 180 x 420 240 x 180 x 420 228 x 305 x 478

Weight 17 17 29.85.5 kg

Maximum Depth 5m 5m 6 m

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLESHOOTING

If this does not solve your problem, please contact the Clarke service

department.

PROBLEM SOLUTION

PUMP WILL

NOT START

1. Make sure that the power is switched on.

2. Check fuse (consult an electrician if in doubt).

3. If extension lead is fitted, check connections (consult an

electrician if in doubt).

4. Internal thermal cut-out has not re-set. Leave for 5-10

minutes and try again.

5. The impeller may be jammed. Disconnect from the mains

supply and remove any objects that may be obstructing

the impeller.

6. Float switch may be jammed against side wall, or

prevented from moving.

7. Water level too low - float switch in OFF position - lift float

to check switch.

8. If the pump still fails to start, consult your CLARKE dealer

for advice.

PUMP WILL

START BUT NOT

PUMP

1. Check that the inlet is not blocked.

2. Check that the discharge tube is not clogged or

obstructed.

3. The head may be too great, i.e. you are trying to lift the

water too great a distance for the pump to cope with.

(“Specifications” on page 7).

4. Air bubble in the pump, produced during the plunge.

Plunge the pump again, at an angle, and shake it whilst

lowering to remove any air trapped in the system.

5. Impeller may be damaged - Consult your CLARKE dealer.

PUMP WILL

NOT STOP

1. Float switch may be prevented from moving to the fully

down position.

2. Float switch may be faulty. Consult your CLARKE dealer

for advice.

PUMP STOPS

RUNNING

1. Thermal overload has operated. Leave for 5-10 minutes

and try again.

2. Pump has run dry, or float switch has cut in.

3. A foreign object has jammed the impeller.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS DIAGRAM HSEC1400A

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST HSEC1400A

Part number = (HGHSE14 + the number of the part)

1 Motor Cover 20 O-ring (Oil Hole)

2 Motor Housing 21 Gasket (Leak Test Hole)

3 Rotor 22 Gasket (Flange)

4 Stator (240V/50HZ) 23 Gasket (Cable)

5 Bearing Cover 24 Flange

6 Oil Seal Cover 25 Hose tail

7 Pump Housing 27 Handle

8 Cutter Impeller (50HZ) 28 Float Switch

9 Strainer 29 Power Cable Set

10 Capacitor 33 Cable Clamp

12 Upper Bearing 34 Cable Fastener

13 Lower Bearing 35 Screw (Cable Clamp)

14 Double Mechanical Seals 36 Screws (Cable)

15 Key 37 Screws (Motor Housing)

16 Oil Seal 40 Screws Strainer)

17 O-ring (Motor/Bearing Cover) 41 Screw (Flange)

18 O-ring (Pump Housing) 42 Nut (Cutter Impeller)

19 O-ring (Oil Seal Cover) 45 Spring Washer (Cutter Impeller)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Wasserpumpe Handbücher

Clarke

Clarke SUBMERSIBLE PUMP Bedienungsanleitung

Clarke

Clarke PSV3A Bedienungsanleitung

Clarke

Clarke CSE400A Bedienungsanleitung

Clarke

Clarke HIPPO 2 Bedienungsanleitung

Clarke

Clarke PSV1A Bedienungsanleitung

Clarke

Clarke CBM240E Bedienungsanleitung

Clarke

Clarke CD1 - 1 Installations- und Betriebshandbuch

Clarke

Clarke EBP1100 Bedienungsanleitung

Clarke

Clarke PF75A Bedienungsanleitung

Clarke

Clarke CPCDP500 Bedienungsanleitung

Clarke

Clarke CFTP12 Bedienungsanleitung

Clarke

Clarke TAM100 7230035 Installations- und Betriebshandbuch

Clarke

Clarke DFT12A Bedienungsanleitung

Clarke

Clarke ECP20A3 Bedienungsanleitung

Clarke

Clarke CSD4 Bedienungsanleitung

Clarke

Clarke HIPPO-3 Handbuch

Clarke

Clarke STP12 Bedienungsanleitung

Clarke

Clarke CDDFTP Bedienungsanleitung

Clarke

Clarke CVP1000 Kurzanleitung

Clarke

Clarke FP150 Bedienungsanleitung

Clarke

Clarke CPP3000B Bedienungsanleitung

Clarke

Clarke CBP900 Bedienungsanleitung

Clarke

Clarke LEP1A 7260060 Bedienungsanleitung

Clarke

Clarke CGP870 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung