Classic Exhibits Gravitee GK-1012 Handbuch

Order #XXXXX

Top View

Perspective View

10’

GK-1012 General Layout

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

GK-1012 Grid View

Order #XXXXX

Assembly Assembly Cont’d

Side-by-Side Assembly

1) Frames: Place frames side-by-side with one higher than the

other, then slide panel down to lock panels securely together.

2) Corner Connectors: Repeat Step 1 for installing corner

connectors to frames.

Side-by-Side Disassembly

1) Pull pin lock outwards to disengage.

2) Pull frames upward and apart at the same time to detatch.

Push pin lock into hole of connecting frame.

Note: Block on pin lock will secure in groove.

Pin Lock

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Graphic Removal

SEG Graphic Installation

Corner A

Corner D

Corner B

Corner C

It is important to first insert graphic

into each alternate corner, then to

the sides of the frame.

If this is not done, graphic will not fit

into the frame correctly.

Step 1

Insert corner A.

Turn edge of graphic so silicon welt

is perpendicular to face of graphic.

Insert narrow side of welt with fabric

to outside into the channel.

Repeat for other side of this corner.

Step 2

Repeat Step 1 for opposite corner

C, then insert corner B, followed by

corner D, to complete the

installation of the corners.

Step 3

Once all corners are inserted, press

one silicon edge into channel from

corners and work toward the center.

Make sure welt is fully inserted into

channel. Continue until all sides are

done. Smooth out edges of graphic.

To remove the graphic from

the frame, locate the fabric

pull tab.

Gently pull up on the tab to

remove the fabric.

General Information

Order #XXXXX

CEI-110 Profile

Straight Bracket Assembly

1) Slide TWO-PIECE TS RV 4 straight bracket into

Interior Center Slot of extrusion, so that two of the

set screws are inside groove. Tighten two set screws

to secure.

3) Slide connecting extrusion over exposed ends of

bracket & connector. Tighten all remaining set screws

to secure extrusions.

2) Slide one V4 Connector into outer interior groove

of extrusion, so that one set screw is inside groove.

Tighten set screw.

TS RV 4

Bracket

Insert two-piece

bracket into the

interior center slot

of extrusion.

Slide V4 Connector

into front interior

groove.

Secure inserted half of

bracket & connector

using set screws.

Slide connecting

extrusion over

exposed ends

of bracket &

connector.

Completed

Assembly

Secure extrusion,

using remaining

set screws.

Set

Screws

Straight Connection

Corner Connection

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

8 Brackets Total:

(4) - TS RV 2

(4) - A1 L-Brackets

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

Completed

Assembly

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Disassembly

1) Loosen set screws on brackets and slide

extrusions off of brackets.

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide one A1 L-Bracket into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

Corner Bracket Assembly

CEI-110 Frame Assembly

CEI110 Frame Assembly

Order #XXXXX

Crate 1 of 1

Crate Packing

Step 1 of 4

Order #XXXXX

Completed Assembly

Item

Qty.

Description

76” CEI110 Horizontal Extrusion

95” CEI110 Vertical Extrusion

Steps:

1) Assemble extrusions flat on floor.

See CEI152 Frame Assembly sheet.

2) Connect light cords and attach transformers.

See Light to Light Connection and

Light to Transformer Connection details.

Keep A1 brackets attached to extrusions [1] and [2].

Power

Break

Power

Break

Power

Break

Lights

Male

Female

to power Transformer

144W / 6A / 24V

Light to Light Connection

Light to Transformer Connection

Maximum of 11 lights per transformer.

GK-2012 Lightbox Assembly

Step 2 of 4

Order #XXXXX

Assembled

Lightbox

Completed Assembly

Item

Qty.

Description

Base Plate

11.5”w x 95”h Gravitee Panel

94.5” Gravitee Corner Connector w/ Caps

38”w x 95”h Gravitee Panel w/ (2) 91.904“ S44

94.5” Gravitee Corner Connector w/ Caps

11.5”w x 95”h Gravitee Panel

95” Gravitee Corner Connector

Wood Shelf w/ (2) 11” Z41

Steps:

1) Connect lights to top of panel [3]. See Light Connection detail.

2) Attach base plate [5] to horizontal [1], using bolt, washer,

and wing nut.

3) Assemble panels and connectors in numerical order, as shown.

See Gravitee Assembly Instruction sheet for details.

4) Attach assembled lightbox to connector [6]. See Lightbox

Attachment detail.

5) Install SEG graphic to assembled panels. See General

Information sheet for SEG Graphic Installation instruction.

6) Attach shelves to panel [3]. See Shelf Attachment detail.

Keep S44 verticals attached to Gravitee panel [3].

Top View

w/Caps

Top View

w/Caps

Attach frame to

V4 connector

on vertical

extrusion,

using washer

and bolt.

Lightbox Attachment

5/16” Bolt

Washer

Connector

Shelf Attachment

Lock Set Screw

Set screws will face

outward for ease

of assembly.

Insert locks into groove

of Gravitee panel then

tighten set screws.

Back of Shelf

Shelf

Slide light onto clip then lock clip

into groove of horizontal extrusion.

Light Connection

Clip

Light

Clip

Horizontal Extrusion

GK-2012 Backwall Assembly

Step 3 of 4

Order #XXXXX

Cabinet Top

Velcro

Sintra

Light Blocker

Shelf

Align hole with pin Rotate pin. Spring

will push pin into hole.

Cabinet Top Attachment

Hole

Steps:

1) Connect light blocker to Velcro on interior of assembled frame.

2) Attach assembled frame to verticals [3] and [3A].

See Frame Attachment detail.

3) Install SEG graphic to front of assembled frame.

See SEG Graphic Installation detail.

4) Place shelf inside assembled base on top of pins and supports.

5) Place cabinet top on assembled base, then secure with pins.

See Cabinet Top Attachment detail.

Completed Assembly

SEG Graphic

Attach frame to

connector on

vertical extrusion,

using bolt.

Frame Attachment

Bolt

Connector

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

SEG Graphic Installation

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

MOD-1700 Cabinet with USB Ports

Step 4 of 4

Order #XXXXX

Shelf

Support

Door

Infill

Frame Assembly

Item

1,1A

2,2A

3,3A

7,7A

8,8A

Qty.

1,1

2,2

Description

46.25” CEI-110 Horizontal Extrusion

37.5” CEI-110 Vertical Extrusion

37.5” S44 Vertical Extrusion

37.5” S44 Vertical Extrusion w/Door Hinges

37.5” S44 Vertical Extrusion w/Door Stops

37.5” S44 Vertical Extrusion w/Door Hinges

14.153” Z45 Horizontal Extrusion

20.408” Z45 Horizontal Extrusion

Steps:

1) Assemble frame extrusions [1] [1A] [2] and [2A]. See CEI152 Frame Assembly sheet.

2) Connect lights and transformer. See Light to Light Connection and Light to Transformer Connection details.

3) Attach horizontals [7] and [8] between verticals [3] [3A] [4] [5] and [6].

4) Slide Infills between verticals [3] [4] and [3A] [6].

5) Connect doors between verticals [4] [5] and [5] [6]. See Door Connection detail.

6) Attach horizontals [7A] and [8A] between verticals [3] [3A] [4] [5] [6] and on top of infills and doors.

7) Connect shelf supports to Velcro on inside of infills.

Door

Hinge

Slide Pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Connection

Transformer

to power

Lights

Male

Female

Transformer

96W / 4A / 24V

Light to Light Connection

Light to Transformer Connection

Maximum of 9 lights per transformer.

MOD-1700 Cabinet with USB (Cont’d)

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1022 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1594 Handbuch

Classic Exhibits

Classic Exhibits RE-2015 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1012 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-412 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-2084 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1703 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1010 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1590 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2009 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1247 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1121 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1950 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary designs VK-1359 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1960 Supernova Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary design MOD-1524 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1970 Handbuch

Classic Exhibits

Classic Exhibits visionary VK-2098 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits gravitee GK-1012 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken