Classic Exhibits SEGUE DESIGNS VK-1970 Handbuch

Order #XXXXX

SETUP INSTRUCTIONS

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

VK-1970 Supernova General Layout

Plan View

10’

Scale: 18

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all setscrews

and locks during disassembly

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX SEG Graphic Installation

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

Order #XXXXX CEI-110 Frames Assembly

CEI-110 Profile

Straight Connection

Corner Connection

TS RV 4

Bracket

Insert Bracket

into the Interior

Center Slot

of extrusion.

Slide connecting

extrusion over

exposed end

of bracket.

Secure extrusion

using remaining

set screws.

Set

Screw

CEI-110 Frames Assembly

Disassembly

1) Loosen set screws on brackets, then slide

extrusions off of brackets.

Straight Bracket Installation (when required)

1) Slide TWO-PIECE TS RV 4 straight bracket into

Interior Center Slot of extrusion so that two of the

set screws are inside groove.

Tighten two set screws to secure.

2) Slide connecting extrusion over exposed end

of bracket. Tighten two remaining set screws

to secure.

Corner Bracket Installation

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide one A1 L-Bracket into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

8 Brackets Total:

(4) - TS RV 4

(4) - A1 L-Brackets

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

Completed

Assembly

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Completed

Assembly

Secure inserted half

of bracket, using

set screws.

Order #XXXXX

Case 1 of 3

Case Packing

2 4 4A2A 3 5

6,7

8,8

8A,8A

6A,7A

5A3A

Top View of Each Level

Level 1 Level 2 Level 3

Base

Plates

Graphic

Setup Hardware

Order #XXXXX

Case 2 of 3

Case Packing

Counter Top

Door

Blocker Fabric

Top View of Each Level

Level 1 Level 2 Level 3 Level 4

1A 2 2A

Door

Order #XXXXX

Case 3 of 3

Case Packing

Assembled

Counter

Side

Assembled

Counter

Side

Top View of Each Level

Level 1 Level 2 Level 3 Level 4

Shelf

Order #XXXXX

Step 1 of 4

VK-1969 Backwall Assembly

Completed Assembly

Item

2/2A

3/3A

4/4A

5/5A

6/6A

Qty.

1/1

Description

Base Plate

46” CEI-110 Horizontal Extrusion

40” S44 Vertical Extrusion

Steps:

1) Attach base plates [1] to vertical extrusions [2] and [3],

using bolts.

2) Assemble CEI-110 extrusions [2 thru 5A] as shown.

See CEI-110 Frames Assembly sheet for instruction.

3) Attach vertical extrusions [6] to [4] and [6A] to [5],

using bolts.

4) Connect Lights and Transformers, then route cords thru

horizontal [2] and connect to power. See Light to Light

Connection and Light to Transformer Connection details.

5) Install SEG graphic to front and blocker fabric to

back of assembled Backwall. See SEG Graphic

Installation page for instruction.

to power

Lighting Instalation Warning

Bolt Nylon

Washer

If utilizing your own hardware,

purchase Nylon Washers to prevent

metal screw heads from damaging

the circuit board. Attach no more

than seven lights per chain.

Diamond

Washer

Power Break

to power

Lights

Male

Female

144W - 6A

Transformer

Light to Light Connection

Light to Transformer Connection

Order #XXXXX

Step 2 of 4

Shelf

Bolt

Completed Assembly

Item

7/7A

8/8A

Qty.

1/1

Description

40” S44 Vertical Extrusion

12” Z32 Horizontal Extrusion

8” Z32 Horizontal Extrusion

Steps:

1) Attach horizontal extrusions [8] and [8A] to vertical extrusions [7] and [7A],

making sure tops of [8A] are at tops of [7] and [7A].

2) Attach extrusions [8] and [8A] to Backwall vertical extrusions [4] and [5].

3) Connect vertical extrusions [7] and [7A] to base plate, using bolts.

4) Attach horizontal extursions [9] to each side of extrusions

[7] and [7A], making sure tops of [9] are level with tops of [7] and [7A].

5) Connect Shelf to Velcro on tops of extrusions [8A] and [9].

VK-1969 Backwall Attachments

Order #XXXXX

Step 3 of 4

MOD-1700 Counter Assembly

Shelf

Support

Door

Infill

CEI-110 Frame Assembly

Item

1/1A

2/2A

3/3A

7/7A

8/8A

Qty.

1/1

2/2

Description

46.25” CEI-110 Horizontal Extrusion

37.5” CEI-110 Vertical Extrusion

37.5” S44 Vertical Extrusion

37.5” S44 Vertical Extrusion w/Door Hinges

37.5” S44 Vertical Extrusion w/Door Stops

37.5” S44 Vertical Extrusion w/Door Hinges

14.153” Z45 Horizontal Extrusion

20.408” Z45 Horizontal Extrusion

Steps:

1) Assemble Frame Extrusions [1,1A,2,2A]. See CEI-110 Frame Assembly page.

2) Connect Lights and Transformer. See Light to Light Connection and

Light to Transformer Connection details.

3) Attach Horizontals [7] & [8] between Verticals [3,3A,4,5,6].

4) Slide Infills between Verticals [3,4] & [3A,6].

5) Connect Doors between Verticals [4,5] & [5,6]. See Door Connection detail.

6) Attach Horizontals [7A] & [8A] between Verticals [3,3A,4,5,6] and on top

of Infills and Doors.

7) Connect Shelf Supports to Velcro on inside of Infills and insert pins to

Verticals [3] [3A] & [5]. See Shelf Pin detail.

Door

Hinge

Slide Pin into

Hinge attached

to Vertical.

Slide Door

Hinge over Pin.

Door Connection

Transformer

to power

Shelf Pin

1) Slide pin into groove

of Vertical Extrusion.

2) Use hex tool to

tighten pin in place.

to power

Lights

Male

Female

144W - 6A

Light to Light Connection

Light to Transformer Connection

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1022 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1025 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1114 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits euro lt HYBRIDS Mod-1122 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-3006 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1046 Handbuch

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1340 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-411 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

Classic Exhibits

Classic Exhibits visionary VK-2098 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1519 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1556C Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1218 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LTG-1001 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung