Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

BACK VIEW FRONT VIEW

MOD-1722 Backlit Counter

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Corner Connection

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

8 Brackets Total:

(4) - TS RV 2

(4) - A1 L-Brackets

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

Completed

Assembly

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Disassembly

1) Loosen set screws on brackets and slide

extrusions off of brackets.

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide one A1 L-Bracket into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

Corner Bracket Assembly

CEI-110 Frame Assembly

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Graphic

Installation

CEI110 Frame Assembly

Case 1 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Top View of Each Level

Level 1

(Bottom level)

Level 2 Level 3 Level 4 Level 5 Level 6

Door

Counter

Top

Shelf

9 9A

11 11A

16,

16A

17,

17A

8,8A

18,

18A 13

1 2

19A

14 15

19 12

Infills

26,26A

Case Packing

Case 2 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Door

Top View of Each Level

Level 1

(Bottom level)

Level 2 Level 3 Level 4 Level 5

10A

4 5

Counter Top

25A 25

2224 20

Bracket

w/21A Bracket

w/21

Infills

23A23

Graphics

Setup Hardware

Shelf Supports

Case Packing

Step 1 of 3

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

1) Assemble lower horizontals [7,8,9,10] between

verticals [1,2,3,4,5].

2) Slide Infills between verticals as shown.

3) Attach upper horizontals [7A,8A,9A,10A], securing infills.

4) Connect lower horizontals [16,17,18,19] between verticals

[5,12,13,14,15].

5) Slide Infills between verticals.

6) Secure Infills with upper horizontals [16A,17A,18A,19A].

7) Connect doors to vertical [3] and [13]. See Door Connection detail.

Item

7,7A

8,8A

9,9A

10,10A

Qty.

1,1

Description

39.5” S44 Vertical Extrusion

8.341” Z45 Horizontal Extrusion

4” Z45 Horizontal Extrusion

16.067” Z45 Horizontal Extrusion

4” Z45 Horizontal Extrusion

16,16A

17,17A

18,18A

19,19A

1,1

39.5” S44 Vertical Extrusion

4” Z45 Horizontal Extrusion

16.067” Z45 Horizontal Extrusion

4” Z45 Horizontal Extrusion

8.341” Z45 Horizontal Extrusion

16A

19A

18A

17A

18 19

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Connection

Infill

Door

7A 8A

10A

Infill

Door

When assembled

Counter Assembly

Step 2 of 3

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

1) Connect vertical [22] between horizontals [23,23A], &

veritcal [24] between horizontals [25,25A]. Refer to the

CEI110 Frame Assembly general info page.

2) Attach assembled frames to verticals [1] & [15], as shown.

See Frame to Assembly Attachment detail.

3) Slide 2-part Infills into back of both assembled frames &

secure with verticals [11,26] & [11A,26A].

4) Attach horizontals [21,21A] & two brackets to vertical [20],

then attach brackets to CEI110 corners [23/25] & [23A/25A],

inserting Infill. See Z45 & Bracket Connection detail.

Item

11,11A

21,21A

23,23A

25,25A

26,26A

Qty.

1,1

Description

35.853”h Z33 Vertical Extrusion

38.752” TSP2 Vertical Extrusion

3.193” Z31 Horizontal Extrusion

39.5” CEI110 Vertical Extrusion

45.75” CEI110 Horizontal Extrusion

39.5” CEI110 Vertical Extrusion

45.75” CEI110 Horizontal Extrusion

35.853”h GS300 Vertical Extrusion

Frame to Assembly Attachment

Bolt

CEI110

S44

Connector

Slide Connector into S44 vertical, then

tighten set screws to secure. Attach

CEI110 vertical to Connector, using bolt.

Slide Connector into Z31 horizontal, then

tighten set screws to secure. Attach Z31

to Bracket, using bolts. Attach bracket to

CEI110 horizontal, using bolts. Slide TSP2

vertical into slot of Bracket, then

secure lock of Z31 into vertical TSP2.

Connector

Z31

CEI110

TSP2

Z31 & Bracket Connection

Bracket

Corner

Assembly

Infill

11A

26A

25A

21A

Bracket

Infill

Bracket

21A

23A

22 Infill

Infill

When assembled

Counter Attachments

Step 3 of 3

Order #XXXXX

Locked layer contains

placeholder marks.

BACK VIEWFRONT VIEW

***

Completed Assembly

Steps:

1) Connect lighting power cords and attach

transformers. See Light to Light Connection

and Light to Transformer Connection details.

2) Place shelves onto pins. See Shelf Pin detail.

3) Place counter top on top of assembed counter base.

See Counter Top Attachment detail.

4) Install SEG graphics to front of assembled frames.

See SEG Graphic Installation detail.

BACK VIEW FRONT VIEW

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

SEG Graphic Installation

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

Shelf Pin

1) Slide pin into groove

of Vertical Extrusion.

2) Use hex tool to

tighten pin in place.

Align hole with pin Rotate pin. Spring

will push pin into hole.

Counter Top Attachment

Hole

Counter Top

Shelf

Transformer Transformer

to power

Lights

Male

Female

Transformer

Light to Light Connection

Light to Tranformer Connection

SEG Graphic

Counter Attachments (cont’d)

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1247 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1137 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1340 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1005 Handbuch

Classic Exhibits

Classic Exhibits eco systems ECO-4100 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1131 Handbuch

Classic Exhibits

Classic Exhibits visionary design MOD-1524 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1108 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1246 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary designs VK-2084 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1226 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-4022 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1960 Supernova Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1119 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1011 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2101 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1025 Handbuch

Classic Exhibits

Classic Exhibits MAGELLAN DESIGNS VK-1088 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung