Classic Exhibits VISIONARY DESIGNS MOD-1703 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

BACK VIEW FRONT VIEW

MOD-1703 Backlit Counter

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Locked layer contains

placeholder marks.

Adjust connectors if necessary to

prevent gaps in connection.

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Graphic Installation

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Corner

Connectors Corner

Connectors

Corner

Connectors Corner

Connectors

COMPLETED ASSEMBLY

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

CEI110 Extrusion

Profile

CEI110 Corner Connection:

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

3) Tighten all knobs to secure connection.

Disassembly:

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

All knobs must be tightened securely to ensure a proper connection.

CEI110 Assembly & SEG Installation

Step 1 of 3

Order #XXXXX

Locked layer contains

placeholder marks.

Item

Qty.

Description

39.5”h CEI110 Vertical Extrusion

39.5”h S40 Vertical Extrusion

39.5”h CEI110 Vertical Extrusion

20.906”w Z45 Horizontal Extrusion

18”w CEI110 Horizontal Extrusion

Side Light Panel

Steps:

1) Attach vertical [1] to vertical [2]. See CEI110 to S40 Connection detail.

Repeat step, attaching vertical [4] to vertical [3].

2) Connect horizontals [5,6] between verticals [2,3].

3) Attach Door to back of assembly, between verticals [2,3].

See Door Attachment detail.

4) Connect horizontals [7,8] to vertical [1], inserting Light Panel.

Repeat step, connecting horizontals [9,10] to vertical [4],

inserting Light Panel.

FRONT VIEW

TOP VIEW

Door

Connector

set

screw

bolt

S40

CEI-110

CEI110 to S40 Connection

Slide V4 connector into groove of S40

extrusion as shown; secure with set screw.

Attach CEI-110 extrusion to S40 by

securing bolt to hole of V4 connector.

Light

Panel Light

Panel

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Attachment

When assembled

Counter Assembly

Step 2 of 3

Order #XXXXX

Locked layer contains

placeholder marks.

When assembled

Item

Qty.

Description

38.752”h TSP2 Vertical Extrusion

35.853”h GS310 Veritcal Extrusion

2.955”w Z140 Horizontal Extrusion

32”w CEI110 Horizontal Extrusion

Bracket

Front Light Panel

Steps:

1) Assemble horizontals [13,14] between verticals [11,12] inserting infill;

Attach Brackets to top & bottom of horizontals [13,14] using bolts.

Refer to Corner Assembly detail.

2) Attach corner assembly to horizontals [7,15] & [8,16], inserting Light Panel.

3) Attach corner assembly to horizontals [9,15] & [10,16].

4) Connect transformer to side & front light panels.

Corner Assembly

(Qty. 2)

Bracket

bolts

Infill

11 12

Light Panel

Corner

Assembly

Corner

Assembly

Bracket

bolts

Attach bracket to

CEI110 horizontals,

using bolts &

V4 Connectors.

Bracket Connection

Set

Screw

Bolt

V4 Connector

TOP VIEW

TSP2

GS310

Z140

Bracket

Transformer

144W / 6 Amp / 24V

1) Connect light strips together & attach transformers.

2) Run power cords out hole in back of light panel to power source.

3) Connect light panel to Velcro on back of extrusions.

To Transformer

Light Strip Connector

Cord

Connect light strips

together, as shown.

Light to Light

Attachment

Light to Transformer

Attachment

Light Panel Connection

Counter Assembly (cont’d)

Step 3 of 3

Order #XXXXX

Locked layer contains

placeholder marks.

FRONT VIEW

Shelf Pin

1) Slide pin into groove

of Vertical Extrusion.

2) Use hex tool to

tighten pin in place.

Align hole with pin Rotate pin. Spring

will push pin into hole.

Counter Top Attachment

Hole

aphi

Counter Top

Shelf

G Graphic

Steps:

1) Apply SEG graphics to assembled base. Refer to the SEG Installation general information page.

2) Place Shelf onto pins. See Shelf Pin detail.

3) Attach Counter Top to assembled base. See Counter Top Attachment detail.

Completed Assembly

Counter Assembly (cont’d)

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1025 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1226 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1091 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1950 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionarydesigns VK-2957 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LT-116 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1010 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids VK-1049 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1181 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2038 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1019 Handbuch

Classic Exhibits

Classic Exhibits visionary designs MOD-1529 Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-1359 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408B Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1011 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1232 Handbuch

Classic Exhibits

Classic Exhibits visionary VK-2098 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1180 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1960 Supernova Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-2008 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung