Classic Exhibits Eco systems ECO-4100 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

Plan View

20’

ECO-4100 - 20’ x 20’ Display

REV 10/2022

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Plan View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Assembly Assembly Cont’d

Stacking Unstacking

Stacking Assembly

1) Place one horizontal frame on top of the other, lining up the

center grooves.

2) Turn stacking lock clockwise to tighten into place. Repeat

for each lock.

Stacking Disassembly

1) Turn the stacking lock counter-clockwise to loosen.

2) The whole spring on the stacking lock should be in view to

release each frame. The disengaged spring should release

the stacking lock. If not, keep turning the stacking lock until

it disengages.

Side-by-Side Assembly

1) Frames: Place frames side-by-side with one higher than the

other, then slide panel down to lock panels securely together.

2) Corner Connectors: Repeat Step 1 for installing corner

connectors to frames.

Side-by-Side Disassembly

1) Pull pin lock outwards to disengage.

2) Pull frames upward and apart at the same time to detatch.

Push stacking lock into the slot

of the upper frame, then spin the

cap to tighten the lock.

Push pin lock into hole of connecting frame.

Note: Block of pin lock will secure in groove.

Disengage the stacking lock by

spinning the cap counter

clockwise and pulling down.

Cap

Stacking

Lock

Pin Lock

Top View

Corner Connector

SEG

Grooves

Note: Orientation of Corner

Connector may change.

Gravitee Assembly

Order #XXXXX

Straight Connection

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

COMPLETED ASSEMBLY

3) Tighten all knobs to secure connection.

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

CEI152 Profile

Slide both connectors across seam of extrusions.

Tighten all knobs.

All knobs must be tightened securely to ensure a proper connection.

Corner

Connectors Corner

Connectors

Corner

Connectors Corner

Connectors

Straight Connector

2) Loosen all knobs, then slide straight

connectors across the seam of extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

CEI152 Frame Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Step 1 of 10

Order #XXXXX

Using Your Setup Instructions

The Aero Setup Instructions are created specifically for your configuration. The instructions include an

exploded view of the frame which is sequentially labeled. We encourage you to review the instructions

before attempting to assemble your exhibit.

Connections are kept very simple; no tools required. Everything assembles with push-button connectors.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Push-Button

Numbered Label

Connections are made by holding the button down and

sliding the red tube into opposing tube until button locks

into the hole of the opposing tube. To disassemble, push button

and pull or twist extrusions apart.

Locked layer contains

placeholder marks.

When assembled

Steps:

1) Assemble lower parts labeled [1] through [18] together in numerical order.

2) Assemble upper parts labeled [19] through [36] together in numerical order

3) Connect upper & lower assemblies together using (8) verticals [V].

4) Attach end pieces [1/19] & [18/36] to frame.

5) Apply Pillowcase Graphic to assembled frame.

12 13 14 15

end

piece

end

piece

30 31 32 33

34 35

Aero Frame Assembly

Step 2 of 10

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

Refer to the Gravitee Assembly general information page.

1) Assemble Gravitee posts & panels [1] through [10] together

in numerical order as shown.

Top View

When assembled

Item

Qty.

Description

38”w x 95”h lower Gravitee Panel

94.5”h lower Gravitee Corner Post w/ caps

38”w x 95”h lower Gravitee Panel

94.5”h lower Gravitee Corner Post w/ caps

38”w x 95”h lower Gravitee Panel w/ Door

94.5”h lower Gravitee Corner Post w/ caps

38”w x 95”h lower Gravitee Panel

94.5”h lower Gravitee Corner Post w/ caps

Lower Gravitee Tower Assembly

Step 3 of 10

Order #XXXXX

Locked layer contains

placeholder marks.

When assembled

Steps:

Refer to the Gravitee Assembly general information page.

1) Assemble Gravitee posts & panels [1] through [10] together

in numerical order, while attaching to lower panels.

2) Attach horizontal [1] between panels [3] & [9].

Keep internal extrusions

attached to Gravitee panels.

DO NOT REMOVE.

Item

Qty.

Description

38”w x 95”h upper Gravitee Panel w/ S44

94.5”h upper Gravitee Corner Post w/ caps

38”w x 95”h upper Gravitee Panel

94.5”h upper Gravitee Corner Post w/ caps

38”w x 95”h upper Gravitee Panel w/ S44

94.5”h upper Gravitee Corner Post w/ caps

38”w x 95”h upper Gravitee Panel

94.5”h upper Gravitee Corner Post w/ caps

38.5”w Z45 Horizontal Extrusion

Upper Gravitee Tower Assembly

Step 4 of 10

Order #XXXXX

Locked layer contains

placeholder marks.

aphi

Steps:

1) Apply SEG graphics to tower assembly

as shown.

G Graphic

aphi

Doo

Graph

SEG Graphic Installation

Corner A

Corner D

Corner B

Corner C

It is important to first insert

graphic into each alternate

corner, then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab. Gently pull up on

the tab to remove the fabric.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

Tower Graphics

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1137 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1011 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1226 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1012 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1703 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1340 Handbuch

Classic Exhibits

Classic Exhibits Perfect 10 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1702 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-406B Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1222 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits SYK-1029 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1711 Handbuch

Classic Exhibits

Classic Exhibits RE-2015 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Classic Exhibits

Classic Exhibits euro lt HYBRIDS Mod-1122 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits eco systems ECO-4100 Handbuch

Beliebte Inneneinrichtung Handbücher anderer Marken