Classic Exhibits Visionarydesigns VK-2957 Bedienungsanleitung

www.classicexhibits.com

Step 1

Page 1 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

Perspective View

Plan View 20’

10’

VK-2957 - General Layout

www.classicexhibits.com

Step 2

Page 2 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - General Information

The Tool Typical Connection

Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most Visionary Designs exhibits can be

assembled with the supplied Hex Key Tool.

Occasionally, a flat head screwdriver may

be required.

Most horizontal extrusion connections have a patented expandable lock. This lock inserts into

the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock

and creates a strong positive connection.

Remove only (1) setscrew when disassembling. Replace setscrew in

extrusion after assembling it. Before packing, replace setscrew in

extrusion to avoid losing it.

Attach base plate to round or square

vertical extrusion using the bolt provided.

Be careful not to strip the threads.

When vertical extrusions are packed in

portable cases rather than crates or

tubs, they must broken down into

smaller sections which then require

assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews in

extrusion after assembling it. Before

packing, replace setscrews in extrusion

to avoid losing them.

Using Your Setup Instructions

The Visionary Designs Setup Instructions are created specifically for your

configuration. They are laid out sequentially, including an exploded view of

the entire display, and then a logical series of detailed steps to assemble the

main structure and components. We encourage you to study the instructions

before attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your

exhibit to prevent loss of the locks and setscrews (see below in RED).

This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only

non-abrasive cleaners.

2) When cleaning laminate inserts or countertops, use mild cleansers and a

soft material such as cotton.

3) Keep all display components away from extreme heat and long exposure

to sunlight to avoid warping and fading.

4) Retain all packing material. It will make re-packing much easier and will

reduce the likelihood of shipping damage.

Typical Connection (cont’d)

Numbered Label

Each extrusion contains a numbered label which

corresponds with setup instructions.

The label is located within a groove of the extrusion

(when possible). With Visionary Designs the labels

contain Black numbers unless otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

www.classicexhibits.com

Step 3

Page 3 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - General Information

Graphic Removal

Graphic: To Ensure Proper Fit

Corner A

Corner D

Corner B

Corner C

It is important to first insert graphic

into each alternater corner then to

the sides of the frame.

If this is not done, graphic will not fit

into the frame correctly.

Step 1

Insert corner A.

Turn edge of graphic so silicon welt

is perpendicular to face of graphic.

Insert narrow side of welt with fabric

to outside into the channel.

Repeat for other side of this corner.

Step 2

Repeat Step 1 for opposite corner

C, then insert corner B, followed by

corner corner D, to complete the

installation of the corners.

Step 3

Once all corners are inserted, press

one silicon edge into channel from

corners and work toward the center.

Make sure welt is fully inserted into

channel. Continue until all sides are

done. Smooth out edges of graphic.

To remove the graphic from

the frame, locate the fabric

pull tab.

Gently pull up on the tab to

remove the fabric.

SEG Graphic Installation

www.classicexhibits.com

Step 1

Page 1 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Backwall Assembly

6A 3

Item

6/6A

Qty.

1/1

Description

96”h Q914 Square Vertical Extrusion

96”h TSP46 Vertical Extrusion

Item

7/7A

8/8A

Qty.

1/1

Description

92.417”h Z45 Vertical Extrusion

34”w TSP46 Horizontal Extrusion

68”w TSP46 Horizontal Extrusion

34”w TSP46 Horizontal Extrusion

68”w TSP46 Horizontal Extrusion

81.275”w Z45 Horizontal Extrusion

Steps:

1) Connect vertical extrusion [6] to vertical [5].

See Custom Cam Lock detail.

Repeat step for connecting verticals [3] & [6A].

2) Attach horizontal extrusions [23] between verticals [2] & [3].

NOTE: Velcro needs to face interior of setup.

3) Assemble horizontals [7], [7A] & [7B].

See TSP46 Connection detail.

Repeat step for horizontals [8], [8A], [8B].

4) Connect assembled horizontals between vertical assemblies

[5/6] & [3/6A]. See Corner Connections detail.

5) Attach vertical extrusion [6B] between assemblies

[7/7A/7B] & [8/8A/8B].

6) Apply fabric blocker to the velcro on [2/3/23].

7) Install SEG Fabric Graphic to [6/6A/7/7A/8/8A].

See SEG Graphic Installation Page in the General Information.

Top View Cam

Lock

Custom Cam Lock

TSP46

Screw clamps

cam lock into

groove of vertical

extrusion.

TSP46 Connection

PR53

Lock

Slide end of extrusion

over corner lock.

Tighten setscrew

to secure extrusions

Corner Connections

Velcro: Bottom

Edge

Velcro: Top

Edge

Velcro

S12

Extrusion

Profile

S12

Q914

www.classicexhibits.com

Step 2

Page 2 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Backwall Assembly Cont’d

12A

13A

24 25

25A

26A

10A

Item

9/9A

10/10A

12/12A

13/13A

25/25A

26/26A

Qty.

1/1

Description

96”h Q914 Square Vertical Extrusion

96”h TSP46 Vertical Extrusion

32”w TSP46 Horizontal Extrusion

16”h TSP46 Vertical Extrusion

29.244”w TSP46 Horizontal Extrusion

96”h Q914 Square Vertical Extrusion

96”h TSP49 Vertical Extrusion

32”w TSP49 Horizontal Extrusion

92.417’h Z45 Vertical Extrusion

Steps:

1) Assemble TSP46 extrusions [9,9A,10,10A].

See Corner Connections detail.

2) Connected assembled TSP frame [9/9A/10/10A]

between verticals [1] & [2].

See Custom Cam Lock detail.

3) Assemble TSP46 extrusions [12,12A,13,13A].

See Corner Connections detail.

4) Connect assembled TSP frame [12/12A/13/13A]

between verticals [3] & [4].

See Custom Cam Lock detail.

Steps Cont’d:

5) Assemble TSP49 extrusions [25,25A,26,26A]

See Corner Connections detail.

6) Connect assembled TSP49 frame [25/25A/26/26A]

between verticals [5] & [24].

See Custom Cam Lock detail.

7) Attach assembled door to vertical [3].

See Door Attachment detail.

8) Apply SEG Graphics to assembled TSP46 Frames.

See SEG Graphic Installation Page in the General Information.

NOTE: SEG Graphics apply to [9/9A/10/10A] & [12/12A/13/13A]

Top View Cam

Lock

Custom Cam Lock

TSP46

Screw clamps

cam lock into

groove of vertical

extrusion.

Lock

Slide end of extrusion

over corner lock.

Tighten setscrew

to secure extrusions

Corner Connections

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin

as shown.

Door

Hinge

www.classicexhibits.com

Step 3

Page 3 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Large D-Frame Light Box Assembly

15B

1717

15A

15C

15B 15

When assembled

Item

15/15A

15B/15C

Qty.

1/1

Description

96”h TSP70 Vertical Extrusion

42”w TSP70 Horizontal Extrusion

150.79”h TSP70 Curved Extrusion

94.937”h Z45 Vertical Extrusion

94.937”h Z45 Vertical Extrusion w/ Holes

Steps:

1) Attach [15B] to [15] & [15C] to [15A].

2) Connect extrusion assmblies [15/15B] & [15A/15C] to vertical extrusion [14]

See TSP70 w/ A1 L-Bracket Connection detail.

3) Attach curved extrusion [16] to the ends of [15B] & [15C].

See TSP70 Connection detail.

4) Connect verticals [17] between horizontals assemblies [15/15B] & [15A/15B].

NOTE: must connect in back groove of TSP70.

5) Attach vertical [18] at connection point of extrusions [15B] & [16].

NOTE: See detail circle.

V4 Connector

TSP70

Tighten

screw

Connect extrusions together

with V4 connector piece and

secure with set screws as shown.

TSP70 Connection

**Slide A1 L Bracket into TSP70

extrusion and secure with set screws.

TSP70 w/ A1 L-Bracket Attachment

Tighten set

screw to secure

Tighten set

screw to secure

www.classicexhibits.com

Step 4

Page 4 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Small D-Frame Light Box Assembly

29A

When assembled

Item

29/29A

Qty.

1/1

Description

96”h TSP70 Vertical Extrusion

3”w TSP70 Horizontal Extrusion

150.7964”h TSP70 Curved Extrusion

Steps:

1) Attach [29] & [29A] to vertical extrusion [28].

See TSP70 w/ A1 L-Bracket Connection detail.

2) Attach curved extrusion [30] to the ends of [29] & [29A].

See TSP70 Connection detail.

V4 Connector

TSP70

Tighten

screw

Connect extrusions together

with V4 connector piece and

secure with set screws as shown.

TSP70 Connection

**Slide A1 L Bracket into TSP70

extrusion and secure with set screws.

TSP70 w/ A1 L-Bracket Attachment

Tighten set

screw to secure

Tighten set

screw to secure

www.classicexhibits.com

Step 5

Page 5 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Assembly of Assemblies

Steps:

1) Connect assembled Large D-Frame to assembled backwall by

using stand-off barrels & Caps.

NOTE: Extrusion [18] will attach to extrusion [4].

See Vertical Extrusion to Post Attachment detail.

Extrusion [14] will attach to extrusion [1].

See TSP70 to Vertical Attachment detail.

Steps:

2) Connect assembled Small D-Frame to assembled backwall by

using stand-off caps.

See TSP70 to Vertical Attachment detail.

3) Apply SEG graphics to D-Frame Light Box.

See SEG Graphic Installation page in General Information

Vertical Extrusion to Post Attachment

Screw

Cap

Stand-off

V20 Connector

Slide V20 connector into groove of vertical extrusion.

Insert threaded Screw Cap through hole in TSP70

extrusion & into threaded hole of V20 connector.

Twist to secure in place.

TSP70 to Vertical Attachment

Screw

Cap

www.classicexhibits.com

Step 6

Page 6 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Wire Management

Wire Connection Point

Power Cord for Monitor

Steps:

1) Connect power cords and DC adaptor cords to LED Tape Lighting.

See LED Tape Lighting Photos & Details detail.

2) Attach monitor mount stand-off barrels to vertical extrusions [17].

NOTE: Screw stand-off barrels into threaded holes of vertical extrusions.

3) Apply SEG fabric graphics to D-Frames and alcove.

See SEG Graphic Installation Page of General Information Pages.

2) Attach monitor mounts to vertical extrusions [17] and [27].

See Monitor Mount Attachment details for Small & Large Monitors.

Super Bright

Normal Bright DC Adapter Cord

Transformer

Connect LED Tape together where

extrusions meet. Attach DC adaptor

and plug into power source.

LED Tape Lighting Photos & Details

Symbol Key

Cord Flow Indicators

Power Strip Plugs

Number of Plugs

Cord Prong Plug End

PR53 Wire Management

Power Cords

(x3)

Wire Connection Points

Transformer will plug into

power strip with Small

Monitor and iPad kiosk.

Power Cord from

Small D-Frame

Transformer

Cords for Monitor & iPad

Transformer

(x3)

www.classicexhibits.com

Step 7

Page 7 of 7

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2957 - Pedestal Assembly

Lock

Infill

When assembled

Foam Lining

Removed

Home Button Shield

Optional Cover for Home Button

1) Remove foam lining from inside bottom of

clam shell as shown.

2) Attach Home Button Shield with double-sided

tape to inside of clam shell, keeping top of

shield flush with clam shell opening as shown.

NOTE: This is a permanent fix and can’t be easily

removed.

Wire

Access

iPad

Lock

Steps:

1) Slide infill between stand verticals as shown.

2) Attach horizontal [20] between stand verticals.

3) Attach base [19] to stand verticals using bolts.

4) Attach square plate [21] to stand using bolt.

5) Attach clam shell [22] to square plate [21] using hex nuts.

6) Insert iPad and feed wire through hole.

7) Attach pamphlet trays to stand. Refer to detail.

Clam Shell

Stand

Base

Plate

Square

Plate

Hex

Nuts

Tools Required:

1) Hex Tool

2) Pliers

Item

Qty.

Description

Base Plate

10”w Z72 Horizontal Extrusion

Mounting Plate

iPad Clamshell

Wire Management for iPad

Feed iPad charging cord through holes from top

to bottom of post as shown.

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits visionary designs VK-1359 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1201 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1005 Handbuch

Classic Exhibits

Classic Exhibits eco systems ECO-2041 Handbuch

Classic Exhibits

Classic Exhibits SYK-1029 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-4022 Handbuch

Classic Exhibits

Classic Exhibits euro lt HYBRIDS Mod-1122 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1109 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS LTK-1152 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1014 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids VK-1049 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1722 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1032 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1556C Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-1214 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 Bella Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1108 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2113 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS 38907 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1246 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits visionarydesigns VK-2957 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken