Classic Exhibits Euro LT Hybrids VK-1049 Handbuch

www.classicexhibits.com

Step 1

Page 1 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

General Layout

10’

Plan View

www.classicexhibits.com

Step 2

Page 2 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

The Tool

Typical Connection Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most exhibits can be assembled

with the supplied Hex Key Tool.

Occasionally, a flat head screw-

driver may be required.

Most horizontal extrusion connections have a patented expandable lock.

This lock inserts into the groove of an opposing extrusion. Tightening the

lock with the Hex Key Tool expands the lock and creates a strong positive

connection.

Remove only (1) setscrew when disassembling.

Replace setscrew in extrusion after assembling it.

Before packing, replace setscrew in extrusion to

avoid losing it.

Attach base plate to round or

square vertical extrusion using

the bolt provided. Be careful not

to strip the threads.

When vertical extrusions are

packed in portable cases rather

than crates or tubs, they must be

broken down into smaller sections

which then require assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews

in extrusion after assembling it.

Before packing, replace setscrews

in extrusion to avoid losing them.

Using Your Setup Instructions

The Euro LT Hybrids Setup Instructions are created specifically for your configuration.

They are laid out sequentially in levels, including exploded views, and a logical series of detailed steps

to assemble the main structure and components. We encourage you to study the instructions before

attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the

locks and setscrews (see below in RED). This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material such as

cotton.

3) Keep all display components away from extreme heat and long exposure to sunlight to avoid warping

and fading.

4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of

shipping damage.

Typical Connection (cont’d) Numbered Label

Each extrusion contains a numbered

label which corresponds with setup

instructions. The label is located within

a groove of the extrusion (when

possible). With extrusion components

the labels contain Black numbers unless

otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

Cut Away View Of

Slide Clips

Left Hand

Grasps Panel

Firmly

With Right Hand Thumb

Close to Seam

Squeeze,

Push Forward,

And Lift

Color Coded Clip

w/ assembly number

Panel Lock

When Required

Black Clip

is bottom of

panel

Connector Top View of Panels with LocksExample of Connection

Color Coded Clip

w/ assembly number

is top of panel

Panel Lock

When Required

Each component has 2 clips,

the lower clip is ALWAYS

black. The top clip is color

coded to distinguish which

level. The color coded clip

also contains the numbered

label.

Components connect together

by aligning them and sliding

downward connecting clips

together.

Configurations are assembled

from left to right, usually starting

with #1 and following the

numbered sequence.

The first level of components contain panel

locks that are located at the top of the

panel for extra stability and seamless con-

nection. When disassembling panels twist

top connection slightly and lift right panel

upward.

General Setup Instructions for Extrusion System

Level 1 = Blue

Level 2 = Red

Level 3 = Green

Level 4 = Black

General Setup Instructions

www.classicexhibits.com

Step 1

Page 1 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Euro LT Panel - Level 1

Item Number

Description

47.5”h x 15”r Curve Panel

47.5”h 180° Connector

47.5”h x 15”r Curve Panel

47.5”h 180° Connector

Steps:

Assemble panels togeter by starting at panel #1

and continue in numerical order.

Level 1

Vertical extrusion must remain

assembled with connector #3Door

Note: Extrusion #3

and connectors #3

must stay assembled

www.classicexhibits.com

Step 2

Page 2 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Euro LT Panel - Level 2

Steps:

Assemble panels togeter by starting at panel #1

Extrusion #3 &

Connector #3

Extrusion #3 &

Connector #3

Extrusion #3 &

Connector #3

Note: Extrusion #3

and connectors #3

must stay assembled

Item Number

Description

18.5”h x 15”r Curve Panel

18.5”h 180° Connector

18.5”h x 15”r Curve Panel

18.5”h 180° Connector

Level 2

Vertical extrusion must remain

assembled with connector #3

www.classicexhibits.com

Step 3

Page 3 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Euro LT Panel - Level 3

Note: Extrusion #3

and connectors #3

must stay assembled

Attach pins to lower inner side of window frame

where indicated, then set shelf atop pins.

Steps:

Assemble panels together by starting at panel #2

and continue in numerical order.

= Indicates Pin Location

Shelf

Item Number

Description

30”h Curve Window Panel w/ Perforated Infill

30”h 180° Connector

30”h Curve Window Panel w/ Perforated Infill

30”h 180° Connector

Window Panel

Level 3

Vertical extrusion must remain

assembled with connector #3

www.classicexhibits.com

Step 4

Page 4 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Backwall Assembly

Item

Qty.

Description

Base Plate

95.751” Vertical Extrusion

77.698” Curve Horizontal Extrusion

Steps:

1) Attach vertical extrusion [2] to base plate [1].

2) Attach horizontal extrusions between vertical

extrusions as show.

3) Apply graphic to assembled backwall.

Refer to

Graphic Tight Fit Detail

detail.

V10 Pressure

Screw

Connector

Piece

Vertical Extrusion Assembly

IF REMOVED

Extrusion #3 and connectors

MUST stay assembled.

Attach back plate to round tower

using screws. Then attach top

plate and tighten setscrews to secure.

Monitor Mount Attachment

**Note: the opening

of SEG extrusions

must face foward

Corner

Connection

Mitre cut

SEG

Extrusion

Profile

Graphic Removal

To remove the graphic from

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

Graphic: To Ensure Proper Fit

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

Note: When applying SEG graphic along

the bottom of curved extrusion #5, double

over the silicone edge of graphic for tight fit.

Step #1 Step #2

Graphic Tight Fit Detail

SEG

Extrusion

Profile

Graphic

www.classicexhibits.com

Step 5

Page 5 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Pedestal Assembly

Item

Description

42”h Round Vertical Extrusion

38”h Round Vertical Extrusion w/ Door Stopper

38”h Round Vertical Extrusion w/ Hinges

42”h Round Vertical Extrusion

31.85” Curved Horizontal Extrusion

23.8” Curved Horizontal Extrusion

16” Horizontal Extrusion

Quantity

Steps:

1) Attach lower horizonal extrusions [13, 14 and 15] between vertical extrusions

[9, 10, 11 and 12] as shown.

2) Place inserts and attach door where indicated.

3) Attach upper horizonal extrusions [13, 14 and 15] between vertical extrusions

[9, 10, 11 and 12] as shown.

4) Velcro internal shelf supports to inside assembled pedestal

5) Set internal shelf atop shelf supports

6) Slide counter top on vertical extrusions [9 and 12] and rest atop pedestal.

7) Attach plex shelf using caps.

10 11

Plex Shelf

Counter

Attach connector piece to rack

as shown. Then connect

assembled literature

rack to vertical extrusion.

Literature Rack Attachment

Tighten Lock

to Secure

Internal Shelf

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Insert

Door

Insert

Cap

Shelf

Support

Velcro

Strip

Top view of

extrusion 17

Hinges

www.classicexhibits.com

Step 6

Page 6 of 6

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Oval Pedestal Assembly

Item

Description

32”h Vertical Extrusion

28.77” Curve Horizontal Extrusion

13.6” Curve Horizontal Extrusion

28.77” Curve Horizontal Extrusion

13.6” Curve Horizontal Extrusion

32”h Vertical Extrusion w/ Door Stop

32”h Vertical Extrusion w/ Door Hinges

28.418”h Vertical Extrusion

Quantity

Steps:

1) Attach lower horizontal extrusions [18 and 19] between vertical

extrusions [17, 22 and 23] as shown.

2) Place inserts and attach door where indicated.

3) Attach upper horizontal extrusions [18 and 19] between vertical

extrusions [17, 22 and 23] as shown.

4) Attach extrusion legs to underside of floor,

5) Attach short pins to lower horizontal extrusions where indicated in ,

then place assembled base on floor.

6) Velcro shelf supports to inside of assembled base, then set shelf atop supports.

7) Connect 2 counters together using standoff extrusions.

8) Attach short pins to upper horizontal extrusions where indicated in,

then place assembled counters atop pins.

Door

Hinges

Door

Stop

Door

= Indicates pin location

***

Internal Shelf

Counter Top

Upper Counter

Standoff Extrusions

Extrusion Legs

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

13.94” x 28.9”

Lam Insert and

Perf Insert Panels

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1970 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-3006 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1960 Supernova Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1702 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1246 Bedienungsanleitung

Classic Exhibits

Classic Exhibits LTK-1139 Bedienungsanleitung

Classic Exhibits

Classic Exhibits eco systems ECO-2041 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1119 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-411 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1711 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1014 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-2038 Handbuch

Classic Exhibits

Classic Exhibits GRAVITEE GOD-1559 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1131 Handbuch

Classic Exhibits

Classic Exhibits eco systems ECO-8C Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1222 Handbuch

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1549 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1144 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1232 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GK-1012 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-2101 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung