Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

www.classicexhibits.com

Step 1

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-1852 - Sunrise Table Top Assembly

Tighten knob

to secure

Corner

Item

Infill

Wing

Description

44”h SEG Vertical Extrusion

24”w SEG Horizontal Extrusion

44”h SEG Vertical Extrusion

24”w SEG Horizontal Extrusion

15”w Horizontal Extrusion

Tighten Knob to secure

Hook keyhole cut

out up bolt

Foot Attachment

Setups:

1) Assembled SEG extrusions together on floor.

Note: Attach infills and wings where indicated.

2) Apply SEG graphic to assembled frame.

3) Attach feet to both sides of assembled frame

where indicated.

When assembled

**** See attached SEG graphic

installation for graphic attachment

www.classicexhibits.com

Step 2

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-1852 - Sunrise Table Top Assembly (Cont’d)

Setups:

1) Attach shelves to assembled SEG table

top using A10 Clamps. Refer to detail.

Shelf

When assembled

Tighten set screw to

secure A10 to extrusion.

A10 Clamp Detail

Tighten knob to secure

shelf in place.

www.classicexhibits.com

Step 3

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-1852- General Information

The Tool Typical Connection

Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most Visionary Designs exhibits can be

assembled with the supplied Hex Key Tool.

Occasionally, a flat head screwdriver may

be required.

Most horizontal extrusion connections have a patented expandable lock. This lock inserts into

the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock

and creates a strong positive connection.

Remove only (1) setscrew when disassembling. Replace setscrew in

extrusion after assembling it. Before packing, replace setscrew in

extrusion to avoid losing it.

Attach base plate to round or square

vertical extrusion using the bolt provided.

Be careful not to strip the threads.

When vertical extrusions are packed in

portable cases rather than crates or

tubs, they must broken down into

smaller sections which then require

assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews in

extrusion after assembling it. Before

packing, replace setscrews in extrusion

to avoid losing them.

Using Your Setup Instructions

The Visionary Designs Setup Instructions are created specifically for your

configuration. They are laid out sequentially, including an exploded view of

the entire display, and then a logical series of detailed steps to assemble the

main structure and components. We encourage you to study the instructions

before attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your

exhibit to prevent loss of the locks and setscrews (see below in RED).

This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only

non-abrasive cleaners.

2) When cleaning laminate inserts or countertops, use mild cleansers and a

soft material such as cotton.

3) Keep all display components away from extreme heat and long exposure

to sunlight to avoid warping and fading.

4) Retain all packing material. It will make re-packing much easier and will

reduce the likelihood of shipping damage.

Typical Connection (cont’d)

Numbered Label

Each extrusion contains a numbered label which

corresponds with setup instructions.

The label is located within a groove of the extrusion

(when possible). With Visionary Designs the labels

contain Black numbers unless otherwise specified.

Detail C EliateDDliateDDetail B

Detail A

Setscrews

www.classicexhibits.com

Step 4

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-1852 - SEG Graphic Installation

Graphic Removal

SEG Graphic: To Ensure Proper Fit

Corner A

Corner D

Corner B

Corner C

It is important to first insert graphic

into each alternater corner then to

the sides of the frame.

If this is not done, graphic will not fit

into the frame correctly.

Step 1

Insert corner A.

Turn edge of graphic so silicon welt

is perpendicular to face of graphic.

Insert narrow side of welt with fabric

to outside into the channel.

Repeat for other side of this corner.

Step 2

Repeat Step 1 for opposite corner

C, then insert corner B, followed by

corner corner D, to complete the

installation of the corners.

Step 3

Once all corners are inserted, press

one silicon edge into channel from

corners and work toward the center.

Make sure welt is fully inserted into

channel. Continue until all sides are

done. Smooth out edges of graphic.

To remove the graphic from

the frame, locate the fabric

pull tab.

Gently pull up on the tab to

remove the fabric.

www.classicexhibits.com

Step 5

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-1852 - Packing Instructions

Level 1 Level 2 Level 3

Graphics

Setup Hardware

Top View of Each Level

Wings

3 4 8 7

1 6

Shelves

(2)Foot

Center Section Assembly

Halogen Lights

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits eco systems ECO-4100 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1624 Handbuch

Classic Exhibits

Classic Exhibits SYMPHONY SYK-1032 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1046 Handbuch

Classic Exhibits

Classic Exhibits vilonary DESIGN MOD-1430 Bedienungsanleitung

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1590 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids MOD-1121 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1711 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1011 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 Helio Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-412 Handbuch

Classic Exhibits

Classic Exhibits LTG-1001 Bedienungsanleitung

Classic Exhibits

Classic Exhibits gravitee GOD-1557 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1341 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1181 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS VK-2959 Handbuch

Classic Exhibits

Classic Exhibits Curved Counter Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-2005 Handbuch

Classic Exhibits

Classic Exhibits SACAGAWEA DESIGNS VK-1226 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung