Classic Exhibits Eco systems ECO-2056 Bedienungsanleitung

Order #XXXXX

Locked layer contains

placeholder marks.

Plan View

10’

20’

ECO-2056 - 10’ x 20’ Display

REV 10/2022

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Plan View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Assembly Assembly Cont’d

Stacking Unstacking

Stacking Assembly

1) Place one horizontal frame on top of the other, lining up the

center grooves.

2) Turn stacking lock clockwise to tighten into place. Repeat

for each lock.

Stacking Disassembly

1) Turn the stacking lock counter-clockwise to loosen.

2) The whole spring on the stacking lock should be in view to

release each frame. The disengaged spring should release

the stacking lock. If not, keep turning the stacking lock until

it disengages.

Side-by-Side Assembly

1) Frames: Place frames side-by-side with one higher than the

other, then slide panel down to lock panels securely together.

2) Corner Connectors: Repeat Step 1 for installing corner

connectors to frames.

Side-by-Side Disassembly

1) Pull pin lock outwards to disengage.

2) Pull frames upward and apart at the same time to detatch.

Push stacking lock into the slot

of the upper frame, then spin the

cap to tighten the lock.

Push pin lock into hole of connecting frame.

Note: Block of pin lock will secure in groove.

Disengage the stacking lock by

spinning the cap counter

clockwise and pulling down.

Cap

Stacking

Lock

Pin Lock

Top View

Corner Connector

SEG

Grooves

Note: Orientation of Corner

Connector may change.

Gravitee Assembly

Order #XXXXX

Straight Connection

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

COMPLETED ASSEMBLY

3) Tighten all knobs to secure connection.

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

CEI152 Profile

Slide both connectors across seam of extrusions.

Tighten all knobs.

All knobs must be tightened securely to ensure a proper connection.

Corner

Connectors Corner

Connectors

Corner

Connectors Corner

Connectors

Straight Connector

2) Loosen all knobs, then slide straight

connectors across the seam of extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

CEI152 Frame Assembly

Order #XXXXX

Straight Connection

All knobs must be tightened securely to ensure a proper connection.

Adjust connectors if necessary to

prevent gaps in connection.

Upper Horizontal Extrusion

Lower Horizontal Extrusion

Straight Connector

Corner

Connectors Corner

Connectors

Corner

Connectors Corner

Connectors

COMPLETED ASSEMBLY

3) Tighten all knobs to secure connection.

Slide verticals over

lower connectors.

Then slide upper

connectors into

groove of verticals.

Tighten all knobs.

When assembling frame, first attach all straight

connectors, then attach corner connectors.

1) Place extrusions end-to-end.

2) Loosen all knobs, then slide straight

connectors across the seam of extrusions.

Disassembly

1) Loosen all knobs.

2) Slide connectors off of one extrusion.

3) Tighten knobs to prevent loss during

packing & shipping.

CEI110 Profile

Slide both connectors across seam of extrusions.

Tighten all knobs.

Corner Connection

3) Tighten all knobs to secure connection.

Disassembly

1) Loosen knobs on vertical extrusions.

2) Slide the vertical extrusions off of

corner connectors on lower and upper

horizontal extrusions.

1) Loosen knobs, then slide vertical extrusions onto

corner connectors of lower horizontal extrusion.

2) Slide corner connectors of upper horizontal

extrusion into grooves of vertical extrusions.

Keep straight connectors in groove of

extrusion. Do not remove connectors

during disassembly.

CEI110 Frame Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Step 1 of 9

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

Refer to the CEI152 Frame Assembly general information page.

1) Assemble verticals [2,4] between horizontals [6,7] using corner connectors.

2) Connect horizontal [8] between verticals [2,4].

3) Attach verticals [9,10] between horizontals [6,8].

Repeat steps 1 through 3 for other kiosk frame assembly.

Section Being Assembled is

Highlighted in BLACK

Assemble frames flat on ground.

FRONT VIEW

left frame right frame

Item

Qty.

Description

95”h CEI152 Vertical Extrusion

48”w CEI152 Horizontal Extrusion

44.353”w Z45 Horizontal Extrusion

72”h Z45 Vertical Extrusion

9 10 24

9 10

Large Side Frames Assembly

Step 2 of 9

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

Refer to the CEI110 Frame Assembly general information page.

1) Assemble verticals [1,2] between horizontals [3,4]

using corner connectors.

2) Attach verticals [5,6] between horizontals [7,8].

3) Connect power cords to Supernova lights.

Item

Qty.

Description

95”h CEI110 Vertical Extrusion

24”w CEI110 Horizontal Extrusion

95”h CEI110 Vertical Extrusion

24”w CEI110 Horizontal Extrusion

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain,

7 lights per Transformer

Light to Transformer Attachment

Power

Female

Transformer

96W / 4 Amp / 24V

FRONT VIEW

left frame right frame

Transformers

Section Being Assembled is

Highlighted in BLACK

Assemble frames flat on ground.

Small Side Frames Assembly

Step 3 of 9

Order #XXXXX

Locked layer contains

placeholder marks.

Section Being Assembled is

Highlighted in BLACK

Steps:

Refer to the Gravitee Assembly general information page.

1) Assemble Gravitee posts & panels [1] through [10] together

in numerical order as shown.

Top View

Item

Qty.

Description

38”w x 95”h lower Gravitee Panel

94.5”h lower Gravitee Corner Post w/ caps

38”w x 95”h lower Gravitee Panel

94.5”h lower Gravitee Corner Post w/ caps

38”w x 95”h lower Gravitee Panel w/ Door

94.5”h lower Gravitee Corner Post w/ caps

38”w x 95”h lower Gravitee Panel

94.5”h lower Gravitee Corner Post w/ caps

Closet Assembly

Inhaltsverzeichnis

Andere Classic Exhibits Inneneinrichtung Handbücher

Classic Exhibits

Classic Exhibits Perfect 10 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Magellan Designs VK-1091 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1341 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1703 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGNS VK-1852 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Visionary Designs MOD-1243 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary designs MOD-1529 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS LTK-1152 Handbuch

Classic Exhibits

Classic Exhibits euro lt HYBRIDS Mod-1122 Bedienungsanleitung

Classic Exhibits

Classic Exhibits visionary MOD-1294 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1011 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Euro LT Hybrids LTK-1119 Bedienungsanleitung

Classic Exhibits

Classic Exhibits SYMPHONY SYM-408B Handbuch

Classic Exhibits

Classic Exhibits Euro LT Hybrids VK-1049 Handbuch

Classic Exhibits

Classic Exhibits Magellan Designs VK-1063 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYK-1016 Handbuch

Classic Exhibits

Classic Exhibits gravitee GK-1008 Handbuch

Classic Exhibits

Classic Exhibits Symphony SYK-1030 Handbuch

Classic Exhibits

Classic Exhibits visionary designs VK-1359 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS MOD-1235 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Symphony SYM-408 Handbuch

Classic Exhibits

Classic Exhibits VISIONARY DESIGNS MOD-1711 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1131 Handbuch

Classic Exhibits

Classic Exhibits visionary DESIGNS VK-1950 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

Classic Exhibits eco systems ECO-2056 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken