Clearaudio Statement Bedienungsanleitung

Hi-Fi Components clearaudio electronic GmbH

Spardorfer Str. 150 ●D-91054 Erlangen ●Tel. +49(0) 1805/059595 ●FAX +49(0) 09131/51683

www.clearaudio.de ●www.analogshop.de ●[email protected] /clearaudio copyright 2008

User Manual

The Statement Turntable

Every market needs a leader

Made in Germany

Version-1.3_10-23-08_English

Statement

User Manual

Page 2 clearaudio electronic GmbH 2008

Dear Statement owner,

Congratulations on your purchase of the

Statement

turntable.

You have purchased a state-of-the-art turntable, the

Statement

, a world class product from

clearaudio electronic GmbH.

The special resonance-optimised construction, the external motor-unit and the patented

clearaudio - CMB-bearing-technology guarantees absolute speed stability, pure pleasure in

listening and reproduction absolutely faithful to the original.

Thank you very much your confidence.

Please read this user manual carefully to ensure that your

Statement

turntable is correctly installed

ready to take you to a new dimension of music reproduction.

We hope you will enjoy your new clearaudio

Statement

turntable.

clearaudio electronic GmbH

Please read the warning before connecting your

Statement

turntable to the mains supply.

CE-MARKING

The clearaudio

Statement

meets the regulations concerning electromagnetic disturbance

(EMC) and low-voltage appliances.

Recording and reproduction of any sound material may require the consent of the creator.

Please acknowledge the information given in the

- Copyright Act 1956,

- Dramatic and Musical Performers Act 1958,

- Performers Protection Acts 1963 and 1072,

- Any more recent legal regulations.

WARNING

Don’t expose your Statement-turntable to rain or excessive humidity.

Don’t handle the mains lead with wet hands.

Don’t place or insert anything into the equipment or through ventilation holes.

No naked flame sources, such as lighted candles, should be placed on the equipment.

Statement

User Manual

Page 3 clearaudio electronic GmbH 2008

Contents

1. Packing content 4

2. Construction overview 6

3. Set up and operation 7

4. Motor adjustment 16

5. Special directions 17

6. Service 18

7. Technical data 19

Warranty information 20

Statement

User Manual

Page 4 clearaudio electronic GmbH 2008

1. Packing content

The

Statement

turntable is packed and delivered on either a Euro pallet or two half size Euro

pallets. The Packing is specially made for the

Statement

- turntable and should be retained for any

repacking.

Please note:

The

Statement -

turntable is very heavy and will require at least two people to unpack and set up.

Attention / Warning :

IMPORTANT!

Before it is fully assembled there are strong magnetic fields around the main

bearing, these could interfere with heart pacemakers and so the Statement

should not be set up by anyone with a pacemaker.

The Statement turntable is extremely heavy and should not be assembled by

anyone with back problems.

The two wooden boxes contain the turntable stand and the pendulum weights, as well as five (5)

separately packed cartons containing all other parts (e.g. massive metal cross, acrylic chassis,

bearings etc).

Please check the accessories contents according to the following list before you set up the

turntable.

1. Two pairs of white gloves 5. Three bases as counter weights (40 mm)

2. Two belts 6. Four bases as flat pads

3. Tool for adjustment of stainless steel

discs (pendulum weight)

7. Polishing paste

4. Three bases as counter weights (20 mm) 8. A set of hex key wrenches

1 2 34

5 6 78

Statement

User Manual

Page 5 clearaudio electronic GmbH 2008

9. Bearing oil 13. Bubble level gauges

10. Acrylic cleaner 14. Not shown:

Two wooden blocks

11. Aluminium screw driver 15. Not Shown:

User manual

12 Statement clamp 16. Not shown:

Warranty card, clearaudio certificate card

(QCQ)

9 10 11

12 13

Statement

User Manual

Page 6 clearaudio electronic GmbH 2008

2. Construction overview

Statement

User Manual

Page 7 clearaudio electronic GmbH 2008

3. Set up and operation

Select the position in which you will use the

Statement

turntable.

Place the

Statement

turntable base in this position on the four

supplied feet.

Place the two wooden blocks beneath the

Statement

base

as shown.

Pic. 1: Placing the Statement

Pic. 2: Placing the Statement

Statement

User Manual

Page 8 clearaudio electronic GmbH 2008

IMPORTANT!

Being careful not to damage the bearing spindle on top of the pendulum shaft, assemble the

pendulum, starting by sliding a solid metal disc over the pendulum shaft so that it rests on the

wooden blocks. Be sure to place a felt mat between each metal disc, building the pendulum with

three solid discs at the bottom, then six half-cut-away discs, then two more solid discs, finally

adding the solid disc engraved with the words clearaudio

Statement.

Please note:

If you are using the

Statement TT1

tangential tonearm, position the half-cut-away discs with the

cut-away section at the rear of the turntable.

Place the four cork damping plates on top of the four corner

pillars.

Again, being careful not to damage the bearing spindle on

top of the pendulum shaft, lower the stainless steel cross

frame over the pendulum shaft so that it rests on the four

cork damping plates.

Disc engraved with

“

Clearaudio Statement”

Disc, solid (2 pcs.)

Disc, half cut away

(6 pcs.)

Disc, solid (3pcs.)

Place a felt mat in

between each stainless

steel platters

Place 4 pcs. damping

plates if not assembled

already from the factory

Pic. 3: Placing the discs

Pic. 4: Placing the cork damping plates

Statement

User Manual

Page 9 clearaudio electronic GmbH 2008

Set the cross shaped massive metal part through the spindle onto the four cork

Tighten the bearing to the shaft by tightening the screws in the bearing collar (8x).

Pic. 5: Placing the metal part

Pic. 5.1: Placing the metal part

Pic. 6: Tighten the bearing

Statement

User Manual

Page 10 clearaudio electronic GmbH 2008

Lift the pendulum shaft to align the V-shaped groove in the pendulum shaft with the locking

screws in the gimbal bearing. Lock the gimbal bearing to the pendulum shaft by fully tightening

the eight screws so that they locate in the groove of the pendulum shaft.

IMPORTANT!

Carefully lift the whole upper section, raising the

pendulum off of the wooden blocks.

Remove the wooden blocks from beneath the turntable

and carefully lower the upper section back onto the

four cork damping plates.

Pic. 7: Lifting the upper part

Pic. 8: Removing the wooden spacers

Andere Handbücher für Statement

Inhaltsverzeichnis

Andere Clearaudio Drehscheibe Handbücher

Clearaudio

Clearaudio Emotion SE Bedienungsanleitung

Clearaudio

Clearaudio Performance DC Bedienungsanleitung

Clearaudio

Clearaudio Innovation Compact Bedienungsanleitung

Clearaudio

Clearaudio Master Innovation Bedienungsanleitung

Clearaudio

Clearaudio Concept MC Technisches Handbuch

Clearaudio

Clearaudio AC039 Bedienungsanleitung

Clearaudio

Clearaudio Ovation Bedienungsanleitung

Clearaudio

Clearaudio Verify Bedienungsanleitung

Clearaudio

Clearaudio TT2 Bedienungsanleitung

Clearaudio

Clearaudio Champion Bedienungsanleitung

Clearaudio

Clearaudio Emotion SE Bedienungsanleitung

Clearaudio

Clearaudio Master-TQ-I Bedienungsanleitung

Clearaudio

Clearaudio Performance DC Bedienungsanleitung

Clearaudio

Clearaudio Ovation Bedienungsanleitung

Clearaudio

Clearaudio Master Innovation Series Bedienungsanleitung

Clearaudio

Clearaudio Smart matrix professional Bedienungsanleitung

Clearaudio

Clearaudio Unify Series Bedienungsanleitung

Clearaudio

Clearaudio concept Signature Bedienungsanleitung

Clearaudio

Clearaudio Melody V2 Bedienungsanleitung

Clearaudio

Clearaudio Emotion CMB Upgrade Kit Bedienungsanleitung

Clearaudio

Clearaudio Emotion Bedienungsanleitung

Clearaudio

Clearaudio Innovation Compact Bedienungsanleitung

Clearaudio

Clearaudio Jubilee MM Bedienungsanleitung

Clearaudio

Clearaudio smart power 12V Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung