Clearaudio Verify Bedienungsanleitung

User manual

Bedienungsanleitung

electronic GmbH, 2018/11 Made in Germany

Verify

User manual / Bedienungsanleitung

2 © clearaudio electronic GmbH, 2018/11

User manual........................................................2 - 12

Bedienungsanleitung ..........................................13 - 23

Dear Clearaudio customer,

Thank you for purchasing the Clearaudio

Verify

radial tonearm.

The innovative

Verify

tonearm is using a friction free magnetic bearing technology and it`s design

allows a very comfortable and easy set up.

Highest demands and Made in Germany, combined with technology and a timeless design enable

the best possible sound enjoyment.

Please read this instruction manual carefully, to avoid any damages or loss of warranty.

This manual will help you for an easy setup and guarantees the highest pleasure for a long time.

We wish you a lot of listening pleasure with your new Clearaudio

Verify

tonearm.

Clearaudio electronic GmbH

Warning

Do not expose the equipment to rain or moisture.

Do not handle the mains lead with wet hands.

No naked ame sources, such as lighted candles, should be placed on the equipment.

Only for use on turntables.

CE-MARKING

User manual / Bedienungsanleitung

Made in Germany 3

Contents

1. List of components.................................................4

2. Verify tonearm mounting.......................................5 - 10

3. Special notes ..........................................................11

4. Technical data ........................................................12

Warranty ....................................................................24 - 25

User manual / Bedienungsanleitung

4 © clearaudio electronic GmbH, 2018/11

1. List of components

Clearaudio has developed special and secure packing for your

Verify

tonearm that ensures safe

transportation.

Please keep this original packing, you will need it if you need to ship the tonearm.

Please check the contents as shown in picture below and in the list at the bottom of this page:

Verify

tonearm

with Direct Wire Plus cable 5. Screws:

- 3 x hex screw M4 x 10

- 1 x grub screw M6 x 8

2. Clearaudio tonearm mounting base

(not included with Performance DC or

Ovation turntable package)

6. Paper tonearm alignment (not shown)

3. Clearaudio counterweight 7. User manual, Quality Certicate,

Warranty card and return delivery note

(not shown)

4. Hex wrench:

- 3 mm

- 2.5 mm

- 1.5 mm

Screwdriver

Pic. 1: List of components

User manual / Bedienungsanleitung

Made in Germany 5

Verify

tonearm mounting

2.1

Please mount the delivered mounting base with the delivered screws onto your tonearm base

(Pic. 1 and 2).

Pic. 2: Mounting the tonearm base

Tonearm mounting base

Tonearm base

Pic. 3: Mounting the tonearm base

Mounting the aluminum clamping ring on a non-Clearaudio turntable:

To install the aluminum clamping ring on the turntable chassis, you will need to drill the required

holes. Please refer to the drilling template shown below (Picture 4) for the measurements to mark

the exact drilling holes.

Please be informed, that this drawing is not suitable for use as a mounting tool.

Use a 3.3 mm HSS drill bit, then cut an M4 thread into each hole using an appropriate tap cutting

tool.

If the turntable chassis material is not suitable for cutting threads, please use a 4.5 mm HSS drill bit

to drill the holes through the material. In this case use standard bolts and nuts to x the arm base.

User manual / Bedienungsanleitung

6 © clearaudio electronic GmbH, 2018/11

Pic. 4: Mounting the aluminum clamping ring on a non-Clearaudio turntable

2.2

Please carefully put the tonearm through the tonearm base (Pic. 5).

Now x the tonearm with the 2 screws and the hex wrench (Pic. 6), not to much, so that you can

ne adjust it in the next steps!

Pic. 5: Assembling the tonearm through the tonearm Pic. 6: Locking the tonearm

User manual / Bedienungsanleitung

Made in Germany 7

2.4

Ensure that the distance from the spindle to the pivot point of the tonearm is exactly 222 mm.

Moving the tonearm base in one direction or another will allow you to locate the correct position.

After you have reached the correct position, tighten the tonearm base again.

Please use the delivered alignment gauge or for more accurate adjustment the professional cartridge

alignment gauge from Clearaudio (Art. No.: AC005 www.analogshop.de ).

Pic. 8: Distance from pivot to stylus

222 mm

2.3

Please mount the cartridge according to the manufacturer`s user

manual. Please pay attention that the protection stylus guard is

attached to the cartridge.

Pic. 7: Cartridge mounting

User manual / Bedienungsanleitung

8 © clearaudio electronic GmbH, 2018/11

Pic. 10: Alignment of the tonearm

Pic. 11: The tonearm tube must be

absolute parallel

2.5 Further adjustments

2.5.1 Tracking force pre-set up

Please check or adjust the tracking force always without a record on the platter! and according to

the cartridge manufacturer`s specication. Please ensure that the height of the measuring platform

on your tracking force gauge is the same height as a record to get an accurate measurement.

The Clearaudio Smart Stylus Gauge or Clearaudio Weight Watcher are recommended.

2.5.2 Adjustment of the tonearm height (Vertical-Tracking-

Angle / VTA)

You can change the height of your tonearm by loosening the two

locking screws on the side of the

tonearm mounting base (Pic. 7). After loosing the screws, you can

move the arm up or down to achieve the required height.

Tighten both screws when nished. Please pay attention to adjust the

tonearm tube parallel to the turntable chassis!

Re-check tracking force after adjusting VTA.

Pic. 9: Adjustment of the tonearm height

2.5.3 Alignment of the tonearm

For the further set-up of the tonearm, you need the cartridge

alignment gauge which is included as well.

Slide the gauge over the spindle of the turntable platter and

turn the platter into the position as shown on the beneath

picture.

Lift down the cartridge and place the diamond tip of the

cartridge on the reference point of the alignment gauge and

make sure that the edges of the tonearm tube are absolutely

parallel to the marking lines printed on the cartridge

alignment gauge. For that adjustment it is necessary to

take a look directly from the top on the tonearm and the

alignment gauge.

If you have to change the position of the diamond tip you

can unscrew the allen screw on the top of the tonearm`s

headshell and move the cartridge into the corresponding

position. Please make also sure that the leading edge of

the cartridge is parallel to the marker lines of the cartridge

alignment gauge. Fix the right position through looking the

headshell screw on the top.

During nal tonearm and cartridge installation, always take

a look from the top onto the alignment gauge, to avoid any

parallax errors.

User manual / Bedienungsanleitung

Made in Germany 9

2.5.4. Adjustment of the Azimuth

The azimuth indicates the angle of the stylus relative to the

record, viewed from the front. It should be exactly 90°.

The Azimuth is already preset at factory.

If you need to change the azimuth, please loosen the screw

on the under side of the tonearm near the headshell using

the 1.5 mm allen key (Pic 10). Now you can change the

azimuth. Once the adjustment is nished, lock the screw on

the under side of the arm tube near the headshell.

The installation is done correctly, when at the same time the

armtube is parallel to the marking lines on the gauge, the

diamond tip is on the reference point and the leading edge

of the cartridge is parallel to the lines on the gauge.

Finally lock all screws that had been involved during the

adjustments.

Pic. 12: Azimuth adjustment

Pic. 13: Stylus tip on reference point

2.5.5. Adjustment of the Tracking force

By loosen the screw on the counterweight on the tonearm-tube you ou can adjust the tracking force

of your cartridge by moving the counterweight (shown in the picture below).

red arrow (to the end of the tonearm)

= lesser tracking force

green arrow (to the beginning of the

tonearm)

= more tracking force

Pic. 12: Adjustment of the tracking force

User manual / Bedienungsanleitung

10 © clearaudio electronic GmbH, 2018/11

2.5.6 Adjustment of the Anti-Skating

You will nd the Anti – skating adjustment wheel on the bottom of the tonearm (Pic. 13).

The factory installation is preset for a clearaudio MM cartridge at tracking force 2.4 grams and

marked with a black stripe on the bolt (view bottom up).

You can change your Anti-Skating:

Clockwise (max. 5 turns)= more Anti - Skating

Counter – clockwise (max. 5 turns) = less Anti - Skating

With 4 turns = Tracking force is 2.2 grams

With 3 turn = Tracking force is 2.4 gram

For a perfect Anti-Skating we recommend the

Clearaudio Test record (LPT43039) available at

www.analogshop.de or contact your nearest dealer or

distributor.

The general set-up is now nished.

Now you can connect your Verify tonearm now with

the phono input of your phono-preamplier.

Attention:

Before the rst use or after a long storage, please apply the lift unit up and down

approximately 4-5 times, so that the oil inside can dissolve in order that the lift unit can

move smoothly.

Pic. 13: Adjustment of the Anti-Skating

Inhaltsverzeichnis

Sprachen:

Andere Clearaudio Drehscheibe Handbücher

Clearaudio

Clearaudio Emotion SE Bedienungsanleitung

Clearaudio

Clearaudio Innovation Wood Bedienungsanleitung

Clearaudio

Clearaudio Reference Jubilee Bedienungsanleitung

Clearaudio

Clearaudio Performance DC Bedienungsanleitung

Clearaudio

Clearaudio Double Matrix Professional SONI C Bedienungsanleitung

Clearaudio

Clearaudio Ovation Bedienungsanleitung

Clearaudio

Clearaudio Moving Coil V2 Bedienungsanleitung

Clearaudio

Clearaudio Master Innovation Bedienungsanleitung

Clearaudio

Clearaudio Emotion SE Bedienungsanleitung

Clearaudio

Clearaudio Concept Bedienungsanleitung

Clearaudio

Clearaudio Perfomance SE Bedienungsanleitung

Clearaudio

Clearaudio concept V2 Bedienungsanleitung

Clearaudio

Clearaudio Charisma V2 MM Bedienungsanleitung

Clearaudio

Clearaudio Satisfy Kardan Bedienungsanleitung

Clearaudio

Clearaudio TT2 Bedienungsanleitung

Clearaudio

Clearaudio Statement V2 Bedienungsanleitung

Clearaudio

Clearaudio Statement Bedienungsanleitung

Clearaudio

Clearaudio Performance SE Bedienungsanleitung

Clearaudio

Clearaudio Magnify Bedienungsanleitung

Clearaudio

Clearaudio Smart Matrix Bedienungsanleitung

Clearaudio

Clearaudio Innovation Compact Bedienungsanleitung

Clearaudio

Clearaudio Statement V2 Bedienungsanleitung

Clearaudio

Clearaudio Master Innovation Bedienungsanleitung

Clearaudio

Clearaudio Charisma V2.1 MM Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung