Code Alarm CA-630 Bedienungsanleitung

Remote Vehicle Control System

IMPORTANT NOTE: The operation of the IV-F65 as described in this manual is applicable

to most vehicles. However, due to the engine type and configuration of some vehicles (i.e.

diesel engines), some functions AND/OR SAFETY PRECAUTIONS may not apply. Please

see your installing dealer for more information.

Car Start, Security and

Convenience System

CA-630TM

Owner's Manual

CA630owners.p65 10/17/03, 4:30 PM1

Features and Benefits of the CODE ALARM CA-630 .............4

UsingYourRemoteTransmitter ....................................................5

Arming the Security System

Pre-arm Mode

Disarming the Security System

Attempted Intrusion Identification

Disabling the IT-sTM Interior Theft Sensor ...................................6

Two-Stage Door Unlock

Activating the Trunk Release Feature

Turning on the Vehicle Headlights

Using the Car Finder Feature

Personal Protection Alarm (Panic)

Remote Start / Stop Feature

UsingValet Mode

Using Your Remote Starter.............................................................7

StartingYourVehicle

If your vehicle stalls or does not start

Remote Start Safety Features

Entering the Vehicle While it is Running via Remote Start

Pre-Heating or Pre-Cooling the Interior of the Vehicle

Using the “Quick-stop” Feature

Automatic Convenience Options..................................................8

When Your Security System is Triggered ...................................8

The Interior Status Indicator ..........................................................8

System Maintenance .......................................................................9

Changing the Remote Control Battery

Adding Remote Controls to Your System

Deleting Lost or Stolen Remote Controls from Your System

Basic Troubleshooting ...................................................................10

Emergency Disarm Procedure ...............................................11

Emergency Disarm Button Location

Code Alarm WarrantyPlan ............................................................12

Code Alarm Theft Protection Plan ..............................................13

Table of Contents

CA630owners.p65 10/17/03, 4:30 PM2

Features and Benefits of the Code Alarm CA-630

Two Easy-to-Use Weather-Resistant Remote Controls

The remote controls included with the Code Alarm CA-630 utilize

durable, moisture resistant cases and sealed rubber buttons for

reliability and long life. Rolling code technology prevents the

transmitter signals from being duplicated. The button functions are

clearly labeled to make the CA-630 simple to operate.

All Entrances Protected

Opening any door or entrance protected by the security system

triggers the vehicle’s horn and flashes the vehicle parking lights.

Starter Disable

The Code Alarm CA-630 protects your vehicle from theft by

disabling the starter when the system is armed.

IT-sTM Interior Theft Sensor

This patented sensor uses infra-red technology to reliably detect

vehicle impact associated with attempted intrusion. The IT-sTM

sensor guards against vehicle body damage, and theft of the

vehicle’s equipment (such as airbags) and personal belongings.

Remote Keyless Entry

The Code Alarm CA-630 conveniently locks and unlocks vehicle

doors and opens the trunk or hatch by remote control.*

Personal Protection Features

Remote Panic Alarm, Illuminated Entry, and Car Finder are among

an array of features that enhance personal safety.**

Interior Status Indicator

The bright-blue warning light is an effective visual deterrent to a

would-be thief.

Remote Start

The Code Alarm CA-630 allows you to warm up your vehicle

and preheat or pre-cool the interior with the press of a button on

the remote control.

PowerRangeTM Antenna

This long-range antenna allows you to operate the Code Alarm CA-

630from distances of up to1/8mile. Remote-start your vehicle from

the safety of your home, apartment or office building.

*If vehicle is equipped with power door locks and they are connected to the alarm system by your installer.

** May require additional connections, components, and/or charges. See your installer for details.

CA630owners.p65 10/17/03, 4:30 PM3

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press* the

LOCK button. The horn will “chirp” twice†and the parking lights will

flash twice, indicating the system is armed. The doors will also lock at

this time (if equipped and connected). The status indicator (blue

warning light on the dash) will blink steadily, once per second.

Pre-arm Mode

If the horn chirps and the parking lights flash only once, this indicates

that the vehicle courtesy light is on, or that an entrance is not closed

securely. Check to see that doors, hood, and trunk are properly

closed. Once all entrances are secured (and the courtesy light is off),

the system will chirp / flash again. The system is now fully armed.

(If the entrance is not secured within 4 minutes, the system will arm

and ignore the unsecured entrance until it is closed.)

Disarming the Security System

To disarm the system, press the UNLOCK button. The horn will chirp

and the parking lights will flash once, and the doors will unlock.

The courtesy light will turn on for 1 minute, or until the vehicle is started.

Attempted Intrusion Identification

If the horn chirps four times when disarming, this indicates that the

system was triggered in your absence. The status indicator will also

flash rapidly. Perform the following operation to determine the protected

zone that triggered the system:

After disarming, press the

emergency override button.

The horn will chirp to indicate

the cause of the alarm trigger:

1 chirp IT-sTM InteriorTheftSensor

2 chirps Door

3 chirps Hood

4 chirps Trunk/Optional Sensors

5 chirps Ignition was turned on

Using Your Remote Transmitter

*Throughout this manual, ‘press’ refers to pressing

for less than 1 second; ‘press and hold’ refers to pressing for more than 1 second.

†If you have chosen the Silent Arming Option, the horn will not sound when arming or disarming until the

appropriate button is pressed a second time.

LOCK Button

Press to Arm Security

System and Lock

Doors

FIND/PANIC Button

Press for Car Finder

Press and Hold for

Panic Alarm

UNLOCK Button

Press to Disarm Security

System and Unlock

Doors

PressTwicefor Two-

Stage Door Unlock*

Press and Hold to Open

Trunk

START Button

Press and Hold for

Remote Start / Stop

Press to Activate

Rear Defroster

CA630owners.p65 10/17/03, 4:30 PM4

Using Your Remote Transmitter (cont.)

Disabling the IT-sTM Interior Theft Sensor

It may be necessary at times to disable the IT-sTM Interior Theft Sensor,

especially when parking in areas (like parking garages) where

extreme vibration may cause false alarms. Press the LOCK buttonand

then press the FIND/PANIC button within two seconds of pressing

LOCK to disable the interior theft sensor.The horn will chirp two times

to indicate that the sensor is disabled. The sensor will become

enabled again the next time the system is armed normally.

Two-Stage Door Unlock

If this feature is enabled on your system, pressing UNLOCK one time

will unlock only the driver’s door. Press UNLOCK again within 1

minute to unlock all doors.

Activating the Trunk Release Feature

Press and hold UNLOCK to open the vehicle trunk or hatch (if

equipped and connected). If this button is used to operate another

accessory, the accessory will stay active for as long as the button is

held.

Using the Progressive Car Finder Feature

Press FIND/PANIC on the remote control to locate your vehicle. The

horn will emit five short chirps at low volume, increasing in volume

each of three times the button is pressed.

Personal Protection Alarm (Panic)

Press and hold the FIND/PANIC button to activate the vehicle horn

and parking lights for 30 seconds. (If the vehicle horn is connected,

the horn will “pulse” for 30 seconds.) Press any remote control button

to turn off the Panic alarm.

Remote Start / Stop Feature

Press and hold START on the remote control. If all safety parameters

are correct, the engine will start within 5 seconds (diesel engines will

take longer.) Press and hold START again to turn off the vehicle. (Turn

to page 6 for more on remote start features.)

CA630owners.p65 10/17/03, 4:30 PM5

Using Valet Mode

If the Passive Arming feature is enabled on your system, Valet mode

temporarily prevents the alarm system from arming automatically.

This is useful when fueling or servicing your vehicle.

To enter Valet Mode:

With the vehicle ignition on, press the LOCK button. The blue

dashboard warning light (status indicator) will turn on for one second,

then turn off. This indicates that the system is in Valet mode. Once the

ignition is turned off, the status indicator will emit a quick double-flash

pattern.

Note: In Valet mode, all keyless entry, convenience and remote start

features operate normally.

To exit Valet Mode:

With the vehicle ignition on, press the UNLOCK button. The blue

dashboard warning light (status indicator) will turn on for one second,

then turn off. This indicates that the system has exited Valet mode.

Hint: To prevent your security system from automatically arming while

unloading or refueling your vehicle, without placing the system in

Valet mode, simply press the disarm button on your remote control

transmitter after turning the ignition key off. Doing so places your

system into a temporary or one time Valet mode. Next time you exit

your vehicle the system will arm in the normal manner.

Using Your Remote Starter

StartingYour Vehicle

The remote start function is activated by pressing and holding the

STARTbutton for 2 seconds on the remote control. The system will

check the vehicle to ensure that it is safe to start, and if all safety

parameters are correct, the engine will start within 5 seconds (diesel

engines will take longer.) Press and hold START again to turn off the

vehicle.

If your vehicle stalls or does not start...

If the vehicle stalls or does not start, the CA-630 will pause 5 seconds,

then try 3 more times to start the vehicle (a total of four attempts). The

system pauses 5 seconds between each start attempt. If the vehicle

does not start after the fourth attempt, the CA-630 will abort the start

process.

Your vehicle can be started by remote control whether the alarm is

armed or disarmed. When the alarm is armed, the impact sensor turns

off when the vehicle is started to prevent the engine vibration from

Using Your Remote Transmitter (cont.)

CA630owners.p65 10/17/03, 4:30 PM6

Using Your Remote Starter (cont’d)

setting off the alarm.

Remote Start Safety Features

For safety and security reasons, the CA-630 will shut off the vehicle

during remote start if any of the following occur:

•The vehicle hood is opened

•The brake is pressed before the vehicle ignition is turned on

with the key

•The engine reaches 3 times its normal idle*

•The alarm is triggered

As a safety precaution, the vehicle will shut off if left unattended for 12

or 25 minutes, depending on the time preset by your installer.

Entering the Vehicle While It is Running via Remote Start

1.Press UNLOCK to unlock the door(s) and turn off the alarm

system (if it is not already off).

2.Enter the vehicle. Do not press the brake pedal.

3.Insert the key into the ignition and turn to the ON position.

4.Press the brake pedal. The remote starter disengages and the

vehicle will operate normally.

Pre-Heating or Pre-Cooling the Interior of the Vehicle

Before exiting the vehicle, set the temperature controls to the desired

setting and operation. After the CA-630 starts the vehicle, the heater

or air-conditioning will activate and heat or cool the interior to your

setting.

Using the “Quick-stop” Feature

If you want to make a short stop and leave your vehicle running (to keep

the interior warm or cool, for instance), the quick stop feature allows

you to do this while keeping your vehicle secure and your keys with you.

To engage quick stop:

1.Stop the vehicle and place the transmission in PARK.

2.With your foot off the brake pedal, press the STARTbutton on

the remote control, the parking lights will turn on, indicating that

the vehicle is now running via remote start.

3.Remove the keys from the ignition and exit the vehicle. Press

LOCK to arm the alarm system if desired.

Note: Do not leave children or animals unattended in the vehicle

when using the quick stop feature.

CA630owners.p65 10/17/03, 4:30 PM7

8Automatic Convenience Options

The CA-630 performs a variety of automatic functions to enhance

security and comfort. Some of these features are programmable at the

time of installation. Please see your installer for further details.

Illuminated Entry

When the alarm system is disarmed, the vehicle courtesy lights will turn

on for 1 minute, or until the vehicle is started or the system is re-armed.

Illuminated Exit

When removing the key from the ignition, the vehicle courtesy lights

will turn on for 1 minute, or until the CA-630 is armed.

Automatic Arming

The CA-630 will arm automatically 1 minute after the key is removed

from the ignition. This feature can be temporarily disabled by placing

the system into Valet mode.

Ignition Lock

If all doors are closed and the vehicle is started with the key, the doors

will automatically lock.

Ignition Unlock

When removing the key from the ignition, the doors will automatically unlock.

When Your Security System is Triggered

The CA-630 will trigger if one of the following events occurs while the

system is armed:

• Any protected entrance is opened

• The vehicle ignition is turned on

• The vehicle is jolted hard enough to signal the impact detector

Once the alarm is triggered, the horn (or horn) sounds and the vehicle

parkinglights flash for 30 seconds.Thesystemwillthenre-arm,awaiting the

next intrusion attempt. To stop the horn while keeping the alarm armed

and doors locked, press the ARM button while the system is triggered.

The Interior Status Indicator

The Status Indicator is a high-intensity red light mounted in a visible

location on the vehicle dashboard. This red light gives a visual indication

of the alarm system’s state of operation. Note the chart below:

If the Status Indicator is... ....then the Security System

Off is disarmed

Flashing Slowly is armed

FlashingVery Quickly was triggered in your absence

(see Attempted Intrusion ID - page 4)

Flashing Intermittently is in Valet mode

(2 flashes, off, 2 flashes)

On (not flashing) is in Pre-arm mode

CA630owners.p65 10/17/03, 4:30 PM8

System Maintenance

Changing the Remote Control Battery

The12-volt alkaline batterysuppliedinyourremote

transmitter should last approximately one year,

depending on usage. When the battery begins to

weaken, you will notice a decrease in range, or

the distance from your vehicle that your remote

transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

1. Using a coin pry off the back of the transmitter (the

transmitter snaps together) and expose the battery.

2. Remove the old battery and replace with GP-23A or

equivalent. Be sure to observe the (+) and (-) signs in the battery

compartment.

3. Replace the case backing, then test the remote transmitter.

It is not necessary to re-program the remote transmitter after

changing the battery.

Adding Remote Controls to Your System

The CA-630 has the ability to operate from up to eight (8) remote

controls. Follow these instructions to add a remote control to your

system.

1. Make sure the system is disarmed and the ignition is off.

2. Open the driver’s door.

3. Turn vehicle ignition on.

4. Press and hold emergency override button.

After 15 seconds, the horn will sound three (3) times. This

indicates that the unit has entered the remote control

programmingmode.

5. Release the button.

6. Press the LOCK button (button 1) on the remote control to be

programmed.

The horn will sound once, indicating that the system has

“learned” that remote control.

7. Repeat step 6 for any additional remote controls.

8. Turn the vehicle ignition off to exit the programming mode.

Test all remote controls to ensure that they work properly.

Open Back of

Remote Transmitter

CA630owners.p65 10/17/03, 4:30 PM9

Basic Troubleshooting

This section outlines some of the basic issues you may experience

while becoming used to the IV-F65. If you have a problem that is not

covered by this section, please consult your installer.

Symptom Problem Solution

Remote control does

not work

Weak or dead battery

Remote control not

programmed

Change battery

Program remote

control (page 9)

System will not arm

Door or other

entrance is open

Courtesy light is on

System is in Valet

mode

Close entrance

Turn courtesy light off

Turn off Valet mode

(page 6)

System will not start Hood is open

Brake is pressed

Close hood

Release brake

System Maintenance (cont.)

Deleting Lost or Stolen Remote Controls from Your System

If one of your remote controls is lost or stolen, follow these instructions

IMMEDIATELYto remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5

of Adding Remote Controls to Your System (page 8).

3a. If you have only one remaining remote control, press the

LOCK button on that remote control eight (8) times, pausing

at least 1 second between each press. Make sure that the

horn chirps each time you press the LOCK button.

3b. If you have two remaining remote controls, press the LOCK

button on each remote control four (4) times, pausing at

least 1 second in between each press. Make sure that the

horn chirps each time you press the LOCK button.

3c. If you have three remaining remote controls, press the

LOCK button on the two remote controls three (3) times,

thenpress the LOCK button on the remaining remote control

twice. Pause at least 1 seconds in between each press.

Make sure that the horn chirps each time you press the

LOCK button.

4. Turn the vehicle ignition off to exit the programming mode.

When you are finished, the lost or stolen remote control will

no longer operate your system.

CA630owners.p65 10/17/03, 4:30 PM10

Andere Handbücher für CA-630

Inhaltsverzeichnis

Andere Code Alarm Fernstartsystem Handbücher

Code Alarm

Code Alarm CA 2050 Bedienungsanleitung

Code Alarm

Code Alarm CA-630 Bedienungsanleitung

Code Alarm

Code Alarm CA 4055 Bedienungsanleitung

Code Alarm

Code Alarm ca6553 Bedienungsanleitung

Code Alarm

Code Alarm CA-430 Bedienungsanleitung

Code Alarm

Code Alarm ca5554 Professional series Bedienungsanleitung

Code Alarm

Code Alarm CA 5055 Bedienungsanleitung

Code Alarm

Code Alarm F60 Bedienungsanleitung

Code Alarm

Code Alarm CA 6150 Bedienungsanleitung

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Code Alarm

Code Alarm ca5154 professional Series Bedienungsanleitung

Code Alarm

Code Alarm F30 Bedienungsanleitung

Code Alarm

Code Alarm CA-520A Bedienungsanleitung

Code Alarm

Code Alarm PC 4400 Bedienungsanleitung

Code Alarm

Code Alarm CA-630 Bedienungsanleitung

Code Alarm

Code Alarm ca 4552 Bedienungsanleitung

Code Alarm

Code Alarm CA 421 Bedienungsanleitung

Code Alarm

Code Alarm ca5554 Professional series Bedienungsanleitung

Code Alarm

Code Alarm PC 4300 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 4050 Bedienungsanleitung

Code Alarm

Code Alarm CA 5051 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 5050 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 4050 Bedienungsanleitung

Code Alarm

Code Alarm CA2LCD5 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung