Cognex Advantage 182 Series Montageanleitung

Advantage®182 Series

Integrator's Guide

2023 May 24

Revision: x82.68

Legal Notices

The software described in this document is furnished under license, and may be used or copied only in accordance with the

terms of such license and with the inclusion of the copyright notice shown on this page. Neither the software, this document,

nor any copies thereof may be provided to, or otherwise made available to, anyone other than the licensee. Title to, and

ownership of, this software remains with Cognex Corporation or its licensor. Cognex Corporation assumes no responsibility

for the use or reliability of its software on equipment that is not supplied by Cognex Corporation. Cognex Corporation makes

no warranties, either express or implied, regarding the described software, its merchantability, non-infringement or its fitness

for any particular purpose.

The information in this document is subject to change without notice and should not be construed as a commitment by

Cognex Corporation. Cognex Corporation is not responsible for any errors that may be present in either this document or the

associated software.

Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part of this document may be

reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, nor transferred to any

other media or language without the written permission of Cognex Corporation.

Portions of the hardware and software provided by Cognex may be covered by one or more U.S. and foreign patents, as well

as pending U.S. and foreign patents listed on the Cognex web site at: cognex.com/patents.

The following are registered trademarks of Cognex Corporation:

Cognex, 2DMAX, Advantage, AlignPlus, Assemblyplus, CheckitwithChecker, Checker, CognexVisionforIndustry,

CognexVSOC, CVL, DataMan, DisplayInspect, DVT, EasyBuilder, Hotbars, IDMax, In-Sight, LaserKiller, MVS-8000,

OmniView, PatFind, PatFlex, PatInspect, PatMax, PatQuick, SensorView, SmartView, SmartAdvisor, SmartLearn,

UltraLight, VisionSolutions, VisionPro, VisionView

The following are trademarks of Cognex Corporation:

The Cognex logo, 1DMax, 3D-Locate, 3DMax, BGAII, CheckPoint, CognexVSoC, CVC-1000, FFD, iLearn, In-Sight (design

insignia with cross-hairs), In-Sight2000, InspectEdge, Inspection Designer, MVS, NotchMax, OCRMax, PatMaxRedLine,

ProofRead, SmartSync, ProfilePlus, SmartDisplay, SmartSystem, SMD4, VisiFlex, Xpand

Other product and company trademarks identified herein are the trademarks of their respective owners.

Legal Notices

Precautions

To reduce the risk of injury or equipment damage, observe the following precautions when you install the Cognex product:

lConnectivity is possible through 24 V DC (+10%) output connection using a UL or NTRL listed power supply. Any

other voltage creates a risk of fire or shock and can damage the components. Applicable national and local wiring

standards and rules must be followed.

lThis product is intended for industrial use in automated manufacturing or similar applications.

lThe safety of any system incorporating this product is the responsibility of the assembler of the system.

lDo not install Cognex products where they are exposed to environmental hazards such as excessive heat, dust,

moisture, humidity, impact, vibration, corrosive substances, flammable substances, or static electricity.

lRoute cables and wires away from high-current wiring or high-voltage power sources to reduce the risk of damage or

malfunction from the following causes: over-voltage, line noise, electrostatic discharge (ESD), power surges, or other

irregularities in the power supply.

lDo not expose the image sensor to laser light. Image sensors can be damaged by direct, or reflected, laser light. If

your application requires laser light that might strike the image sensor, use a lens filter at the corresponding laser

wavelength. For suggestions, contact your local integrator or application engineer.

lThis product does not contain user-serviceable parts. Do not make electrical or mechanical modifications to product

components. Unauthorized modifications can void your warranty.

lChanges or modifications not expressly approved by the party responsible for regulatory compliance could void the

user’s authority to operate the equipment.

lInclude service loops with cable connections.

lEnsure that the cable bend radius begins at least six inches from the connector. Cable shielding can be degraded or

cables can be damaged or wear out faster if a service loop or bend radius is tighter than 10X the cable diameter.

lThis device should be used in accordance with the instructions in this manual.

lAll specifications are for reference purposes only and can change without notice.

Precautions

Table of Contents

Legal Notices 2

Precautions 3

Table of Contents 4

Product Overview 6

Communication Options 6

Reader Layout 7

Getting Started 8

Setting up the Reader 8

Accessories 10

Cables 10

Mounting 10

Illumination 10

Configuring In-Sight Vision Suite 12

Develop a Job File 14

Mechanical Information 17

Advantage 182 Dimensions 17

USB-C Connector Dimensions 18

RJ-45 Connector Dimensions 19

Device Label Information 20

Environmental Maximum Conditions 20

Electrical Information 21

Connectors 21

Ethernet 21

USB-C Connector 21

Power Characteristics 22

Communication Interfaces 23

Digital Input Lines 23

Digital Output Lines 23

Status LEDs 24

USB-C-DB15 Cable 26

Optics and Lighting 28

Lens 28

Fields of View 29

Changing Illumination Modules 31

Adjusting Focus Distance 34

Cleaning and Maintenance 36

Clean the Housing 36

Clean the Reader Image Sensor Window 36

Clean the Reader Lens Cover 36

Regulations and Conformity 37

中国大陆RoHS (Information for China RoHS Compliance) 38

Table of Contents

For European Community Users 38

Table of Contents

Product Overview

The Advantage 182 device is a compact smart camera with integrated lighting.

Advantage 182 provides the following connection options:

lStandard RJ-45 Ethernet

lUSB-C

Communication Options

Advantage 182 provides the following connection and communication options:

lEthernet 10/100/1000

Standard RJ-45 Ethernet connection.

Configure the device through Ethernet connection with a PC running In-Sight Vision Suite software.

Note: Advantage 182 does not support Power over Ethernet. Connecting your device to a PoE network can

cause damage to the device.

lUSB-C

You can use any powered USB-C connection to power the Advantage 182.

The DB-15 to USB-C cable contains active components which allow you to connect the Advantage 182 to a power

supply of up to 24 V while using the pins of the USB-C connector for Input/Output signals.

Product Overview

Reader Layout

The image and table below show the elements of the reader.

Number Description

1 Error LED indicator

2 Communication LEDindicator

3 Pass/Fail LED indicator

4 Train status/Trigger status LED indicator

5 Power LEDindicator

6 RJ-45 Ethernet connector

7 USB-C connector

Note: For more information on LED functions, see the Status LEDs section in Communication Interfaces on page23.

Product Overview

Getting Started

Setting up the Reader

1. Install In-Sight Vision Suite.

a. Go to https://support.cognex.com/en/downloads/in-sight and select Software & Firmware.

b. Find the installer that matches the firmware version of your Advantage device. For example: In-Sight 23.1.0.

Tip: To find the latest In-Sight installer, sort the list by clicking the arrow pointing downwards next to

DATE.

c. Download and install the software.

2. Connect the cables.

a. Connect both the USB-C and the Ethernet cable to the device, and secure the cable screws.

b. Plug in the other end of the Ethernet cable to your network switch or host machine.

c. Connect the host end of the USB-C cable to the power supply. You can power the device in the following

ways:

lUsing a USB-C cable connected to a USB-A or USB-C port.

lUsing the Cognex USB-C – DB-15 cable:

i. Connect the power supply to pin 5 of the DB-15 connector.

ii. Use a DB-15 – USB-A adapter cable and connect it to a USB-A port.

Getting Started

3. Connect the device to In-Sight Vision Suite.

a. Launch In-Sight Vision Suite.

b. Locate your Advantage device on the left side of the window. The device name conforms to the following:

For example: ADV182C-93fce0

c. Click on the camera to see the System Info tab.

Troubleshooting: The device does not appear in In-Sight Vision Suite.

Probable Cause Solution

The Advantage device has static IP address, which does

not reside on the same subnet as the PC running In-Sight

Vision Suite.

Click on the cog icon to access Settings, go to Device

Discovery, and enable the Discover Misconfigured

Devices option.

Getting Started

Accessories

The following accessories are compatible with the Advantage 182. For more information, contact your local Cognex sales

representative.

Cables

The following cables are compatible with Advantage 182 devices, and can be purchased separately:

Accessory Product Number Illustration

USB-C - DB15 right angle cable, 0.5m, Power, Input/Output, Serial CCB-PIO-DB15-05RA

USB-C - DB15 straight cable, 0.5m, Power, Input/Output, Serial CCB-PIO-DB15-05ST

DB15 - USB-A adapter cable, 1.5m, Power DM100-USB-000

USB-C - USB-A right angle cable, 2.5m, Power DMA-RTCBLE-IP65-25

USB-C - USB-A straight cable, 2.5m, Power DMA-STCBLE-IP65-25

RJ45 - RJ45 right angle cable, 2m CCB-ETH-RJ45-2RA

Mounting

The following mounting brackets are compatible with Advantage 182 devices, and can be purchased separately:

Accessory Product Number Illustration

Universal mounting bracket DM100-UBRK-000

For creating custom mounting solutions, refer to the mounting hole positions in Advantage 182 Dimensions on page17.

Illumination

The following accessories are Cognex configurable options, and cannot be purchased separately:

Getting Started

Inhaltsverzeichnis

Andere Cognex Barcode-Lesegerät Handbücher

Cognex

Cognex DataMan 300 Series Bedienungsanleitung

Cognex

Cognex DataMan Betriebsanleitung

Cognex

Cognex DataMan 370 Series Bedienungsanleitung

Cognex

Cognex DataMan 8072 DL Bedienungsanleitung

Cognex

Cognex DataMan 360 Series Bedienungsanleitung

Cognex

Cognex DataMan 300 Series Bedienungsanleitung

Cognex

Cognex DataMan 60 Series Bedienungsanleitung

Cognex

Cognex DataMan 260 Series Bedienungsanleitung

Cognex

Cognex DataMan 300 Series Bedienungsanleitung

Cognex

Cognex DataMan 470 Series Bedienungsanleitung

Cognex

Cognex DATAMAN 500 Bedienungsanleitung

Cognex

Cognex DataMan 260 Series Bedienungsanleitung

Cognex

Cognex DataMan 8050 Bedienungsanleitung

Cognex

Cognex DATAMAN 500 Bedienungsanleitung

Cognex

Cognex DataMan 503 Bedienungsanleitung

Cognex

Cognex DataMan 300 Series Bedienungsanleitung

Cognex

Cognex DataMan 8700 DX Bedienungsanleitung

Cognex

Cognex DataMan 7550 Bedienungsanleitung

Cognex

Cognex DataMan 50 Bedienungsanleitung

Cognex

Cognex DataMan 8600 Series Bedienungsanleitung

Cognex

Cognex DataMan 50 Bedienungsanleitung

Cognex

Cognex DataMan 150 Series Bedienungsanleitung

Cognex

Cognex DataMan 8600 Verifier Series Bedienungsanleitung

Cognex

Cognex In-Sight 2800 Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung