CommScope AMP NETCONNECT MRJ21 1479452-1 Bedienungsanleitung

Figure 1

MRJ21 cassette assemblies listed in Figure 1 are

designed to be installed into Patch Panel 1479451–1.

Back Cable Manager Kits 1933352–[ ] (shown in

Figure 1) can be used to support the trunk cable. The

patch panel and cable manager kit are designed to be

mounted onto a standard 483–mm [19–in.] Electronic

Industries Alliance (EIA) rack or equipment cabinet.

Read these instructions thoroughly before starting

installation.

Reasons for reissue of this instruction sheet are

provided in Section 5, REVISION SUMMARY.

The front of each cassette assembly features two

plungers used to secure the assembly to the patch

panel and a chamfered corner that indicates Port 1.

The shielded cassette also has a 1/4–turn fastener

used for bonding. The back of each cassette

assembly features an MRJ21 receptacle that accepts

the connector of the trunk cable. See Figure 1.

Using the mounting screws, mount the patch panel

and cable manager kit onto the rack, then proceed as

follows:

To obtain information on CommScope®products,

contact your local CommScope®account

representative, PartnerPRO™Network Partner

or visit our website at www.commscope.com

This product is covered by one or more U.S.

patents or their foreign equivalents. For patents, see

www.commscope.com/ProductPatent/ProductPatent.aspx

Dec. 2016 Rev G

™

To obtain information on CommScope

products,

visit the CommScope website at

www.commscope.com

1. Pull the plungers of the cassette away from the

face of the cassette.

2. Facing the front of the patch panel, align the

cassette with an opening in the patch panel so that

the chamfered corner is on the left (as shown in

Figure 1). This orientation is recommended so that

Port 1 of all cassettes are located at the same

position.

Note that for the shielded cassette, the 1/4–turn

fastener must align with the hole above the

mounting holes in the patch panel.

3. Slide the cassette into the opening of the patch

panel then push the plungers into the holes in the

patch panel. An audible click indicates that the

plungers are fully seated. For the shielded

cassette, using a small cross–recessed tipped

screwdriver, turn the 1/4–turn fastener

clockwise

the locked position.

4. Plug the connector of the trunk cable into the

receptacle (at the back) of the cassette. Refer to

Figure 2. Make sure to align the keying features of

the connector and receptacle. Ensure that the

connector is fully seated,

then

using a small

cross–recessed tipped screwdriver, turn the jack

screws of the receptacle

clockwise

and tighten to a

maximum torque of 0.23 Nm [2 lbf–in.].

5. Using cable ties or similar fasteners, attach the

trunk cable to the tie–down bar. It is recommended

to maintain a minimum bend radius of 50.8 mm

[2 in.] when securing and routing cables. See

Figure 2.

Figure 2

For port–to–cable pair cross–reference, refer to

Figure 3. Port numbers are based on the orientation

of the cassette assembly.

Figure 3

Revisions to this instruction sheet include:

Corrected part numbers for shielded cassette

assemblies

Rebranded to CommScope

Dieses Handbuch passt für folgende Modelle

Andere CommScope Kabel und Steckverbinder Handbücher

CommScope

CommScope FDH1204-24SE2 Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT SL Series Bedienungsanleitung

CommScope

CommScope M2400 Series Bedienungsanleitung

CommScope

CommScope BUDI-S Bedienungsanleitung

CommScope

CommScope FIBER INDEXING TERMINAL Bedienungsanleitung

CommScope

CommScope FIST-RSKG-16 Bedienungsanleitung

CommScope

CommScope SYSTIMAX VisiPatch CPC5562 Bedienungsanleitung

CommScope

CommScope FOSC450 C Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT 1711357-1 Bedienungsanleitung

CommScope

CommScope OSP-CLPFEC-LG Bedienungsanleitung

CommScope

CommScope NOVUX SEC 100 Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFA208 Series Merkblatt

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope HELIAX MFJS6UDHNA00 Bedienungsanleitung

CommScope

CommScope LightCrimp Plus SC Simplex Bedienungsanleitung

CommScope

CommScope LightCrimp Plus LC Bedienungsanleitung

CommScope

CommScope TDUX-35 Bedienungsanleitung

CommScope

CommScope LightCrimp Plus ST Bedienungsanleitung

CommScope

CommScope ETHERSEAL 1479563-2 Bedienungsanleitung

CommScope

CommScope FD21206-48SRC Series Merkblatt

CommScope

CommScope FOSC 450 A Bedienungsanleitung

CommScope

CommScope NOVUX SXT Bedienungsanleitung

CommScope

CommScope FIST-RSKG-1 Bedienungsanleitung

CommScope

CommScope PICABOND 60944-6 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung