CORNING LSE 6755 Bedienungsanleitung

INSTRUCTION MANUAL

Models:

6755 – 120V

6756 – 100V

6758 – 230V UK

6759 – 230V EU

CLS-EQ-104 October 2013 , Document 01, Revision 02

CONTENTS

1 PRODUCT DESCRIPTION

1.1 Usage in accordance with safety standards

1.1.1 General Information

1.1.1.1 Hazards and precautions

1.1.1.2 Brief description

1.1.1.3 Safety Standards

1.1.1.4 Extent of supply

1.1.1.5 Warranty

1.2 Installation

1.2.1 Installation of the centrifuge

1.2.1.1 Unpacking the centrifuge

1.2.1.2 Space requirements

1.2.1.3 Installation

1.3 Technical Data

1.4 Conformity Declaration

1.5 Basic Adjustments

1.5.1 Access to mode “operating data “

1.5.2 Call up of operating data

2 OPERATION

2.1 Installation of rotors

2.1.1 Mounting and loading angle rotors

2.1.2 Mounting and loading swing out rotors

2.1.3 Overloading of rotors

2.1.4 Removing the rotors

2.2 Operation

2.2.1 Power switch

2.2.2 Lid release

2.2.3 Lid lock

2.2.4 Pre-selection of speed/RCF-value

2.2.5 Pre-selection of running time

2.2.6 Pre-selection of brake intensity and acceleration

2.2.7 Starting the centrifuge

2.2.8 “Stop“key

2.3 Safety features

2.3.1 Imbalance detection

3 MAINTENANCE

3.1 Service and Maintenance

3.1.1 Maintenance and cleaning

3.1.2 Glass breakage

3.1.3 Disinfection of Alu-rotors

3.1.4 Disinfection of PP-rotors

3.1.5 Cold room removal

4 TROUBLE SHOOTING

4.1 Error messages: Cause / Solution

4.2 Survey of possible error messages and their solutions

4.2.1 Lid release during power failure

4.2.2 Description of the error message system

4.2.3 Error messages

5 RECEIPT OF CENTRIFUGES TO REPAIR AND DISPOSAL

5.1 Receipt of Centrifuges to Repair

5.2 Disposal

CLS-EQ-104 October 2013 , Document 01, Revision 02

1 PRODUCT DESCRIPTION

1.1 Usage in accordance with safety standards

1.1.1 General information

1.1.1.1 Hazards and precautions

Before setting the centrifuge into operation, please read this instruction manual carefully!

This centrifuge must not be operated by unqualified personnel not being familiar with thecorrect use of

the unit. Always, use the original accessories only!

For your personal safety, please pay attention to following precautions:

•The Corning LSE™ Compact Centrifuge is not explosion-proof andmust thereforenot be

operated in explosion-endangered areas or locations. During centrifugation, it is prohibited to

stay within the safety zone of 30 cm around the centrifuge or deposit hazardous substances

within this area.

•Centrifugation offlammable, explosive and radioactive substances or substances, which

chemically react with high energy, is strictly prohibited!

•Never spin toxic or pathogenic material without adequate safety precautions, i.e. centrifugation

of buckets / tubes without or with defective hermetic sealing’s is strictly prohibited.

•The user is obligated to perform appropriate disinfection procedures in case dangerous

substances have contaminated the centrifuge and / or its accessories. Whencentrifuging

infectious substances, always pay attention to the General Laboratory Precautions. If

necessary, contact your safety officer!

•It is prohibited to run the centrifuge with rotors other than listed for this unit.

•Under no circumstances openthe lid of the centrifuge while the rotor is still running or rotating

with a speed of > 2 m/s.

Following rules must strictly be adhered to:

•Do not operate the centrifuge in case it is not installed correctly.

•Do not operate the centrifugewhen dismounted (e.g. withouthousing).

•Do not run the centrifuge when mechanical or electrical assembly groups have been tampered

with by unauthorized persons.

•Do not use accessories suchas rotors and buckets, which are not exclusively approved by

Corning, Incorporated. except commercially available centrifuge tubes made of glass or plastic.

•Do not spin extremely corrosive substances, as they may cause material damages and impair

mechanical resistance.

CLS-EQ-104 October 2013 , Document 01, Revision 02

•Do not operate the centrifugewith rotors orbuckets, which show anysigns of corrosion or

mechanical damage.

1 PRODUCT DESCRIPTION

The manufacturer is responsible for safety and reliability of the centrifuge, only if:

•The unit is operated in accordance with this instruction manual.

•Modifications, repairs or other adjustments are performed by Corning-authorized personnel and

the electrical installation of the related location corresponds to the IEC-regulations.

1.1.1.2 Brief description

Corning LSE™ Compact Centrifuge is asmall centrifuge. You can use swing out and angle rotors in

this centrifuge. Rotors are not included with thecentrifuge and can be purchased separately. All

relevant run parameters can easily be set withkeys and be pre-selected with the main adjusting knob.

All pre-selected, respectively actual values are permanent displayed on large LED’s

The lid is latched and releasedwith an electronic lid lock.

The centrifuge has a powerful, maintenance-free motor with a low noise level.

1.1.1.3 Safety standards

Following standards have been considered for the production of our centrifuges:

•Accident Prevention Regulation for electrical unitsand installations UVV VBG4

•Accident Prevention Regulation for centrifuges as per BGR 500; Chapter 2.11; Part 3

•DIN 58970 part 1, 2 and 4 forcentrifuges and tubes

•Electrical Interference Suppression according to interference degree B as per VDE 0871

•Electrical Safety as per IEC1010-1 and IEC1010-2-D

•European Standard PR EN 61 010-1 and PREN 61 010-2-2

CLS-EQ-104 October 2013 , Document 01, Revision 02

1 PRODUCT DESCRIPTION

1.1.1.4 Extent of supply

Following partsare supplied as accessories with each centrifuge:

•1 Instruction manual (included with each centrifuge)

1.1.1.5 Warranty

The centrifugehas been subjected to thorough testing and quality controls.

In the unlikelycase of any manufacturing faults occurring,the centrifuge and rotors arecovered by

warranty for a period of two years from date of delivery.

This warranty becomes invalid in case of mishandling, damage and negligence and furtherin case of

usage of inappropriate spare parts and / or accessories or unauthorized modification of the unit.

Technical modification rights are reserved by the manufacturer in respect to technical

improvement.

1.2 Installation

1.2.1 Installation of the centrifuge

1.2.1.1 Unpacking the centrifuge

The Corning LSE™ Compact Centrifuge is supplied in a carton.

Remove the strap retainer, open the carton and remove the centrifuge. Remove all material inside unit.

The instruction manual must always be keptwith the centrifuge.

1.2.1.2 Space requirements

The centrifugeshould be installed on an even and solidsurface, if possible on a laboratory cabinet /

table or some other solid vibration free surface.

In order to enable a safe and smooth operation, level the centrifuge witha spirit level.

The centrifugemust be placed in a way,that there is a minimum space of 30 cm oneach side of theunit

in order to ensure necessary heat dissipation.

Do not place thecentrifugenext to a window or a heater, where it couldbe disposed toexcessive heat,

as the performance of the unitis based on an ambient temperature of 23°C.

Safety regulations require that the safety area of 30 cm around the unit is marked in order to indicate that

neither hazardous substances nor personsshould be within this area during centrifugation.

1.2.1.3 Installation

Follow these steps:

•Check whetherpower supply corresponds with the one named on the manufacturer's rating

label which is mounted on the rear panel.

CLS-EQ-104 October 2013 , Document 01, Revision 02

•The line voltage circuit breaker is max. 10 A (type K) slow release for commonly used

instruments.

•In case of emergency, there must be an emergency switch off installed outside the room in

order to disconnect the powersupply of the unit.

•Remove the transport spacer blocks from the motor shaft (see chapter 2.2.2)

The socket for the power cord must be easy to reach respectively easy to disconnect!

1 PRODUCT DESCRIPTION

1.3 Technical Data

Type / Model

Corning LSE™ Compact

Centrifuge

Dimensions

Width

Depth

Height

28 cm

37 cm

26 cm

Weight

15 kg

Noise level (max.)

60 +2,0 dB (A)

Max. speed

Max. volume

Max. RCF

Admissible density

Admissible kinetic energy

6000 rpm

6 x 50 ml

4185 x g

1,2 kg/dm3

1694 Nm

Electrical connection AC

Current

Connected load

230 V / 50 Hz 1 ph

0,55 A

100 Watt

120 V / 60 Hz 1 ph

1,1 A

100 Watt

Interference suppression

VDE 0871, Funkentstörgrad B

Test obligations

To be filled in by purchaser:

Inventory-No.:

Check-No.:

Location:

Maintenance contract:

Your service department

Your agent

CLS-EQ-104 October 2013 , Document 01, Revision 02

1PRODUCT DESCRIPTION

1.4 Conformity declaration

Declaration of Conformity

Corning Life Sciences herebyconfirms that the product

Corning LSECompact Centrifuge

Models: 6755, 6756, 6757, 6758

Is in accordance with the following directives and standards:

2006/95/EC Low Voltage Directive

2004/108/EC EMC Directive

2006/95/EC Machine Directive

2002/95/EC RoHS

2006/96/EC WEEE

_____________________________________

Michael Rosenblum

This equipment has been

tested and found to comply

with the limits for a Class A

digital device, pursuant to

both Part 15 of the FCC

Rules and the radio

interference regulation of the

Canadian Department of

Communications. These

limits are designed to provide

reasonable protection against

harmful interference when the

equipment is operated in a

commercial environment.

This equipment generates

uses and can radiate radio

frequency energy and, if not

installed and used in

accordance with the

instruction manual, many

cause harmful interference to

radio communications.

Operation of this equipment

in a residentialarea is likely

to cause harmfulinterference

which case the user will be

required to correct the

interface at his own expense.

CLS-EQ-104 October 2013 , Document 01, Revision 02

1 PRODUCT DESCRIPTION

1.5 Basic adjustments

Before the first operation and after each rotor change, you have to enter the respective rotor type.

Part #

Description

Rotor

Code

480136

Corning® LSE™ 6 x 50 mL Fixed Angle Rotor

480137

Corning® LSE 12 x 15 mL Fixed Angle Rotor

480138

Corning® LSE 6 x 5 mL Swing-Out Rotor

480139

Corning® LSE 18 x 1.5 mL Fixed Angle Rotor

480143*

Corning® LSE 15/50 mL Fixed Angle Combi Rotor

*For serial numbers before 7412 5031 (120V) or 7412 0011 (230V)

-multiply the displayed G force by 1.05

*For serial numbers after 7412 5031 (120V) or 7412 0011 (230V)

Switch on the unit and open the lid. Now presssimultaneously the keys “lid “(1) and “stop” (2). In the

display “rpm/rcf” then appearsthe old settled rotor type, i. e. “96”. With the adjustmentknob (7) you can

settle the used rotor now. (See photo 1) To adopt the data in the unit please press the “start” key. Inside

the display the stroke “store” appears to the confirmation.

Now all important rotor parameters for the centrifuge are stored.

Photo 1

CLS-EQ-104 October 2013 , Document 01, Revision 02

1 PRODUCT DESCRIPTION

1.5.1 Access to mode “Operating Data“

In this mode you can check the following points:

These are in detaill:

1. Number of starts

2. Operating hours of the centrifuge

3. Software-version

4. Error list

5. Operation of imbalance sensor

6. Operation of keyboard

7. Display test

If the centrifuge is still turned off, press simultaneously the keys “time“ (4) and „lid“ (1) and turn on the

main switch of the centrifuge. Now release both keys again. As a result a display test is executed for

approx. 5 seconds. All possible indications will appear at thesame time (see photo 2).

CLS-EQ-104 October 2013 , Document 01, Revision 02

Photo 2

ATTENTION:

Please notice that you mustenter the program as described under point 1.5.1 to change the

adjustments of the points 1.5.2. After you have stored the settings you change to the normal

program mode again by switch off the centrifuge for a short while.

1 PRODUCT DESCRIPTION

1.5.2 Call up of operating data

In the mode “Basic Adjustments” you can call up the operating data of the centrifuge.

Please proceed as describedunder point 1.5.1 to enter this program mode.

Press the key “accel/decel“(5). In the display “accel/decal” flashes the word “service”“.

With the adjusting knob (7) the differentinformation can be called up:

A = previous starts of the centrifuge (see photo 3a)

H = previous operating hours

S = software version

E = list of previous error messages

U only for service purpose

The list of the last 99 error messages can belooked over bypressing the key „rpm/rcf“ (6) and leaf

through it by the adjusting knob (7). The respective error codes appear in the display „rpm/rcf“

(see photo 3b). Please look up in chapter 4.2.3 ofthis instruction manual for the relevant meanings.

The first two numbers (X) indicate the appeared errorsongoing from 00 to 99, the last twonumbers (Y)

indicate the error code (i. e. 02= imbalance sensor is defective).

Here as well youmust shortly switch off thecentrifuge for changing to thenormal program mode again.

CLS-EQ-104 October 2013 , Document 01, Revision 02

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CORNING Laborausrüstung Handbücher

CORNING

CORNING LSE Series Bedienungsanleitung

CORNING

CORNING LSE 6875-SB Bedienungsanleitung

CORNING

CORNING Matribot Bioprinter Bedienungsanleitung

CORNING

CORNING Stripettor 4998 Bedienungsanleitung

CORNING

CORNING LSE 6783 Bedienungsanleitung

CORNING

CORNING CamSplice FBC-017 Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING Lambda EliteTouch Bedienungsanleitung

CORNING

CORNING LSE 6775 Bedienungsanleitung

CORNING

CORNING X-LAB 6917 Bedienungsanleitung

CORNING

CORNING PC-611 Bedienungsanleitung

CORNING

CORNING Matribot 6150 Bedienungsanleitung

CORNING

CORNING PC-170 Bedienungsanleitung

CORNING

CORNING AXYGEN AxySpin R Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING LSE 6783 Bedienungsanleitung

CORNING

CORNING Axygen Axypet Pro Bedienungsanleitung

CORNING

CORNING Matribot Bioprinter Bedienungsanleitung

CORNING

CORNING Gosselin S-Blender 1 Produktinformationsblatt

CORNING

CORNING Axygen Axypet Bedienungsanleitung

CORNING

CORNING LSE 6785-SB Bedienungsanleitung

CORNING

CORNING Spin-X UF 6 Gebrauchsanweisung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung