CORNING Gosselin S-Blender 1 Produktinformationsblatt

Short User's Manual Gosselin S-Blender 1

Page 1 of 2

1. INTENDED USE

S-Blender 1 is used for homogenization of the samples in the bags and produces a liquid suspension for further analysis.

2. OVERALL VIEW

3. CONTROL PANEL DESCRIPTION

1 Fast, Normal and Slow indicator lights - for speed indication

2 SPEED key - for speed setting (Fast, Normal and Slow)

3 Time display

4 TIME key - for time setting (in 10 s steps, Min 30 s, Max 210 s, Hold)

5 PROGRAM SELECT key (0 - 9)

6 PROGRAM SET key - for entering/exiting the program setting mode

7 Program setting mode indicator light

8 Program number display

9 RUN indicator light

4. SETTINGS

Plug the power cord to mains socket of the device and to a grounded wall socket. Push the handle backward to open the

door. Turn on the main switch on the back side of the device.

Manual settings:

- Set the speed by pressing the SPEED key. You can set Fast, Normal and Slow speed.

- Set the time by pressing the TIME key. You can set the time between 30 and 210 seconds in 10 seconds steps. When

"HLd" is displayed, Hold function is activated and the time is set to continuous operation.

Program settings:

- You can select a program (0 - 9) by pressing PROGRAM SELECT key. The preset speed and time are displayed,

when you select individual programs.

- You can set the preset speed and time for individual programs. Select the program you wish to change by pressing

PROGRAM SELECT key, and then press PROGRAM SET key to enter the program setting mode - key indicator light

turns on. Set the speed by pressing the SPEED key, and time by pressing the TIME key. Press PROGRAM SET key to

confirm the values and exit the program setting mode - key indicator light turns off.

NOTE: Short pressing of the keys are used to increase the values. Long pressing of the keys (over 1 second) are used to

decrease the values.

5. OPERATION

(1)

Push the handle backward

to open the door.

Make sure that waste

drawer of the chamber is

empty.

Set the speed and time

manually or select a

program.

(2)

Insert the bag with the

sample and diluents into

the chamber.

It is recommended to slide

the bag along the door to

remove the air out of the

bag and avoid the leaks

when closing the door.

2 3 4 5 6

Handle

Doo

Control panel

Foot

Waste drawe

Main switch

Fuse compartment

Mains socket

Chamber

Short User's Manual Gosselin S-Blender 1

Page 2 of 2

(3) Pull the handle forward to

close the door.

Blending operation starts

automatically.

Wait until set time elapses

and device stops. Message

"End" appears on display.

If you set the time to "HLd",

you have to open the door

to stop the blending

operation.

(4)

Push the handle backward

to open the door.

Take the bag with the

sample out of the chamber.

NOTE: You can open the door during the blending operation, to check the sample. The time on display stops at current

value, and displays are blinking for 10 seconds. During this time, you can check the sample, and if it is not ready, you

can close the door again to continue the blending operation. The time on display starts running again.

If the sample is ready when you open the door during the blending operation, you can wait for 10 seconds and the

displays stop blinking, or you can press any key to cancel the blinking. This means that the run is ended.

NOTE: You can change speed setting during the operation, but you can't change time and program settings.

6. CLEANING

Before starting a cleaning procedure, turn the main switch off and unplug the power cable!

(1)

Push the handle backward

to open the door.

Reach inside the chamber

with your hands and pull

both paddles off the shafts.

Put the paddles in the

waste drawer of the

chamber.

(2)

Lift the door up to unhook it

from the holders on the

bottom side.

(3)

Turn the bottom side of the

door away from the device.

Unhook the top side of the

door by gently pulling it

away from the top holders.

(4) Pull the chamber away

from the device.

Clean the chamber, the

paddles and the door with

soft cloth and warm water.

For cleaning of the rest of

device use soft damp cloth.

NOTE: To assemble the device, follow the reverse procedure.

7. TROUBLESHOOTING

Following is the table of errors, which could appear on the display of the device, and their descriptions.

ERROR DESCRIPTION

Err 1 Driver error (driver temperature too high).

Err 2 Motor current too big.

Err 3 Motor is not turning for more than 2 seconds.

Err 4 Motor tries to start 5 times, but it can't because of jamming (too hard or too big sample).

NOTE: Some very hard samples, such as shell-fish, may damage the bags and cause leaks. Make sure to use quality

bags and prepare the appropriate samples.

Andere CORNING Laborausrüstung Handbücher

CORNING

CORNING SCF-1296 Bedienungsanleitung

CORNING

CORNING LSE 6770 Bedienungsanleitung

CORNING

CORNING LSE 6755 Bedienungsanleitung

CORNING

CORNING OptiTect Bedienungsanleitung

CORNING

CORNING LSE 6780-4 Bedienungsanleitung

CORNING

CORNING LSE Bedienungsanleitung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING CamSplice FBC-017 Bedienungsanleitung

CORNING

CORNING LSE 6703 Bedienungsanleitung

CORNING

CORNING LSE 6765-HS Bedienungsanleitung

CORNING

CORNING LSE 6780-FP Bedienungsanleitung

CORNING

CORNING 6928 Bedienungsanleitung

CORNING

CORNING LSE 6775 Bedienungsanleitung

CORNING

CORNING PC-611 Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING Matribot 6150 Bedienungsanleitung

CORNING

CORNING LSE 6783 Bedienungsanleitung

CORNING

CORNING AXYGEN AxySpin R Bedienungsanleitung

CORNING

CORNING Everon 6000 Bedienungsanleitung

CORNING

CORNING Spin-X UF 6 Gebrauchsanweisung

CORNING

CORNING PC-400D Bedienungsanleitung

CORNING

CORNING MicroDEN Bedienungsanleitung

CORNING

CORNING LSE 6783 Bedienungsanleitung

CORNING

CORNING LSE 6775 - 120V US Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung