CORNING LSE 6783 Bedienungsanleitung

Corning®LSE™

6L Digital Water Bath

INSTRUCTION MANUAL

Models

6783 (120V US)

6784 (230V EU)

Table of Contents

1.0 Warning

2.0 Safety Information

3.0 Package Contents

4.0 Unpacking

5.0 Installation

6.0 Intended Use

7.0 Symbols and Conventions

8.0 Product Specifications

9.0 Getting Started

10.0 Important Guidelines

11.0 Operation

12.0 Troubleshooting

13.0 Cleaning and Maintenance

14.0 Temperature Re-adjustment

15.0 Product Disposal for Corning Customers and Recyclers

1.0 WARNING

Configuring and operating this equipment requires precise knowledge and observance of

the instructions in this user's manual. The equipment is designed only for its intended

application.

Important safety symbols used in this manual:

Warning!

This is a warning of risk situations and dangers. Failure to observe this warning

could be life-threatening. These warnings must be heeded.

This equipment is designed for 230V/50Hz or 120V/60Hz

Make sure it is connected to the correct power supply. Disconnect the power cord

before carrying out maintenance or cleaning work.

2.0 SAFETY INFORMATION

The responsibility for operating the equipment lies exclusively with the owner or user if said

equipment is incorrectly serviced, maintained, altered by persons not employed by an

authorized dealer, or if the equipment is used in a manner contrary to its specified purpose.

The equipment must be maintained and operated in accordance with this user's manual.

Ensure this user's manual is accessible at all times and has been read and

understood by all users.

3.0 Package Contents

Description

Qty

Water Bath, 6L

User's Manual

Power Cord

4.0 UNPACKING

Carefully inspect the unit and accessories thoroughly upon receipt for any damage that may

have occurred during shipping. Severe damage to the packaging container may indicate

damage to the unit. If you suspect damage to the unit, immediately file a claim with the

carrier in accordance with their instructions before contacting Corning Customer Service.

Also verify that all accessories are included and that the unit is in good working order before

discarding the shipping packaging.

5.0 INSTALLATION

Your satisfaction and safety require a complete understanding of this unit. Read the

instructions thoroughly and be sure all operators are given adequate training before

attempting to put the unit in use.

NOTE: This equipment must be used only for its intended application; any alterations or

modifications will void your warranty and may cause injury.

6.0 INTENDED USE

The Corning®Digital Water Bath is a compact general purpose convection bath capable of

uniformly heating samples up to a maximum of 99°C.

7.0 SYMBOLS AND CONVENTIONS

The following chart is an illustrated glossary of the symbols that are used in this manual.

CAUTION This symbol indicates a potential risk and alerts you

to proceed with caution

CAUTION This symbol indicates the presence of high voltage

and warns the user to proceed with caution

CAUTION This symbol indicates risks associated with hot

surfaces

8.0 PRODUCT SPECIFICATIONS

Temperature range

Ambient +5°C to 99°C

Controls

PID control

Chamber maximum load

20 lbs./9.09 kg

Exterior dimensions (W x D x H)

14.9 x 11.4 x 9.0 inches (12.9 inches with cover)/

38 x 29 x 23 mm (33 mm with cover)

Weight

19 lbs./8.6 kg

Electrical

120V, 50/60 Hz, 4.8 amps or

230V, 50/60 Hz, 2.4 amps or

Chamber dimensions (W x D x H)

12.6 x 6.7 x 6.9 inches/32 x 17 x 18 cm

9.0 GETTING STARTED

9.1 Check the data plate for voltage, cycle, wattage, and ampere requirements. If matched

to your power source, plug the power cord into a grounded outlet. Voltage should not

vary more than 10% from the data plate rating.

9.2 In selecting a location, consider all conditions which might affect performance, such as

heat from radiators, autoclaves, etc. Avoid direct sun, fast-moving air currents,

heating/cooling ducts, and high traffic areas. Allow a minimum of 5 cm between the unit

and walls or partitions which might obstruct free airflow.

10.0 IMPORTANT GUIDELINES

Description of front overlay:

POWER – power key shines when water bath is ON

⇑-- UP key

⇓-- DOWN key

Display (DOT is blinking when you set temperature)

11.0 OPERATION

Do not use this water bath in explosive or flammable environments. Do not

heat or incubate flammable, explosive, or highly reactive materials in this

water bath as serious injury may result.

Temperature of water bath cover and chamber edges may reach over 100°C.

Use protective gloves to avoid burns and injuries.

When opening the water bath cover, beware of steam. It may be very hot and

can cause burns on your face and hands.

Do not use tap water in water bath. You may only use distilled water!

Do not use the water bath without water. Minimum level of water is at least

50 mm.

1. Place the unit on a level surface and plug the unit into a properly grounded outlet of

appropriate voltage.

2. Fill the chamber with desired quantity of distilled water. Normal level of water is 2/3

of chamber height. Minimum level of water is at least 50 mm.

3. Put the stainless steel cover on unit.

4. Press the power switch to the ON position. The switch should illuminate. The water

bath automatically detects and displays the supply frequency as F50 or F60. Water

bath starts to heat.

5. Set desired temperature with UP or DOWN key. You must hold UP or DOWN key

for more than 2 seconds. DOT on DISPLAY blinks. When DOT starts to blink (dot

blinks for 5 seconds), set temperature to desired value between room temperature

+5°C to 99°C. Two seconds after the desired temperature is set, the display will

automatically show momentary temperature.

6. You can always look at set temperature by holding UP or DOWN key for more than

2 seconds.

12.0 TROUBLESHOOTING

Review the information in the table below to troubleshoot operating problems.

Problem on

Display

Cause

Solution

Er1

Temperature probe is not in

range

Examine temperature probe.

Faulty control board.

Er2

Temperature is more than

5°C higher than the set

temperature

Examine SET temperature.

Examine parameters for heating.

Examine parameters for heater.

Faulty control board.

Examine temperature probe.

Er3

If after two hours

temperature does not reach

SET temperature

Examine heater.

Examine temperature safety fuse.

Faulty control board.

13.0 CLEANING AND MAINTENANCE

Prior to any cleaning or maintenance of the unit, disconnect the power cord from the

wall outlet.

1. No routine maintenance is required on the unit.

2. Clean the unit internally and externally with a damp cloth and mild soap. Do not

immerse the unit or spill liquids into or on the unit. Allow the water bath to dry

completely inside and out before reconnecting the power and using.

14.0 TEMPERATURE RE-ADJUSTMENT

Water bath has a software for temperature re-adjustment. You must first measure

temperature in the middle of the chamber or in the sample for a minimum of 2 hours, which

is required to stabilize the temperature. You must measure temperature with a certified

reference temperature measuring instrument with precision of 0.1°C or more. After 2 hours

or more read temperature on thermometer and compare it with temperature on LED

display. Difference between thermometer reading and display is the value, which you will

enter in the software.

Example 1:

Reference Temperature is 37.9°C, temperature on display is 37°C

Difference is 37.9 - 37 = 0.9

Value is 0.9 (value which you enter)

Example 2:

Reference temperature is 36.2°C, temperature on display is 37°C

Difference is 37 - 36.2 = -0.8

Value is -0.8 (value which you enter)

Procedure for Temperature Re-adjustment:

•Press UP and DOWN key at the same time for more than 5 seconds – until Cor

(correction) appears on the display and DOT blinks.

•With UP or DOWN key, define value (when DOT is blinking). Pay attention to the

sign of value (plus or minus). After 5 of defining the temperature – display will

automatically show temporary temperature.

15.0 PRODUCT DISPOSAL INFORMATION FOR CORNING CUSTOMERS AND

RECYCLERS

According to Directive 2012/19/EU of the European Parliament and

Council of 4th July 2012 on waste and electronic equipment (WEEE) as

amended, the Digital Water Bath is marked with the crossed-out wheeled

bin and must not be disposed of with domestic waste.

Consequently, the buyer shall follow the instructions for reuse and

recycling of waste electronic and electrical equipment (WEEE) provided

with the products and available at the following link:

www.corning.com/weee.

For additional information, visit www.corning.com/lifesciences.or call 1.800.492.1110. Outside

the United States, call 978.442.2200.

For Corning technical information, e-mail us at: ScientificSupport@corning.com or call

1.800.492.1110. Outside the United States, call 978.442.2200.

For more specific information on claims, visit the Certificates page at www.corning.com/lifesciences.

Warranty/Disclaimer: Unless otherwise specified, all products are for research use only. Not intended

for use in diagnostic or therapeutic procedures. Corning Life Sciences makes no claims regarding the

performance of these products for clinical or diagnostic applications.

Corning Incorporated

Life Sciences

836 North St.

Building 300, Suite 3401

Tewksbury, MA 01876

t 800.492.1110

t 978.442.2200

f 978.442.2476

www.corning.com/lifesciences

Worldwide Support

Offices

ASIA/PACIFIC

Australia/New Zealand

t 61 427286832

China

t 86 21 3338 4338

f 86 21 3338 4300

India

t 91 124 4604000

f 91 124 4604099

Japan

t 81 3-3586 1996

f 81 3-3586 1291

Korea

t 82 2-796-9500

f 82 2-796-9300

Singapore

t 65 6572-9740

f 65 6861-2913

Taiwan

t 886 2-2716-0338

f 886 2-2516-7500

EUROPE

France

t 0800 916 882

f 0800 918 636

Germany

t 0800 101 1153

f 0800 101 2427

The Netherlands

t 31 20 655 79 28

f 31 20 659 76 73

United Kingdom

t 0800 376 8660

f 0800 279 1117

All Other European

Countries

t 31 (0) 20 659 60 51

f 31 (0) 20 659 76 73

LATIN AMERICA

[email protected]om

Brasil

t (55-11) 3089-7400

f (55-11) 3167-0700

Mexico

t (52-81) 8158-8400

f (52-81) 8313-8589

For a listing of trademarks, visit www.corning.com/clstrademarks.

All other trademarks are the property of their respective owners.

Andere Handbücher für LSE 6783

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CORNING Laborausrüstung Handbücher

CORNING

CORNING Matribot 6150 Bedienungsanleitung

CORNING

CORNING LSE 6770 Bedienungsanleitung

CORNING

CORNING PC-170 Bedienungsanleitung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING Spin-X UF 6 Gebrauchsanweisung

CORNING

CORNING Lambda EliteTouch Bedienungsanleitung

CORNING

CORNING LSE 6775 Bedienungsanleitung

CORNING

CORNING Axygen Axypet Pro Bedienungsanleitung

CORNING

CORNING LSE 6875-SB Bedienungsanleitung

CORNING

CORNING Labnet Prism R Bedienungsanleitung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING X-LAB 6917 Bedienungsanleitung

CORNING

CORNING CamSplice FBC-017 Bedienungsanleitung

CORNING

CORNING LSE 6755 Bedienungsanleitung

CORNING

CORNING 6928 Bedienungsanleitung

CORNING

CORNING LSE 6703 Bedienungsanleitung

CORNING

CORNING SCF-1296 Bedienungsanleitung

CORNING

CORNING LSE 6785-SB Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING Lambda Plus Bedienungsanleitung

CORNING

CORNING Cell Counter Bedienungsanleitung

CORNING

CORNING OptiTect Bedienungsanleitung

CORNING

CORNING Matribot Bioprinter Bedienungsanleitung

CORNING

CORNING Gosselin S-Blender 1 Produktinformationsblatt

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung