CORNING LSE 6775 - 120V US Bedienungsanleitung

INSTRUCTION MANUAL

Models:

6775 – 120V US

6776 -- 230V EU

6777 -- 230V UK

6778 -- 100V JP

CLS‐E

‐98March2010,Document01,Revision01

Warnings

The following precautions should be taken when operating or working near the Corning

LSEVortex Mixer:

•Always wear safety glasses and other appropriate protection when operating this

equipment.

•Never operate the unit without a shaking head securely attached.

•Shake hazardous samples in appropriate containment vessels.

•Do not stir volatile materials.

•Do not immerse the unit for cleaning.

•Do not modify or substitute the grounded power plug. Use only power cords

supplied by the manufacturer. Use only properly grounded outlets to avoid shock

hazard.

•Do not modify the unit electrically or mechanically as personal injury or product

damage may occur.

•Not explosion or spark proof.

•Not for industrial use. These units are designed for use in laboratory

environments by persons knowledgeable in safe laboratory practices.

•Do not use equipment in a manner other than stated in Operating Conditions

(Page # 2) since the protection provided by the equipment may be impaired.

•Do not turn speed knob counterclockwise from the “0” or off position.

•Repair should be performed only by qualified individuals.

Contents

Operating Conditions ……………………………………………………………... 1

General Information ……………………………………………………………….. 2

Technical Specifications …………………………………………………………. 2

Unpacking the CorningLSEVortex Mixer …………………………………. 2

Installation …………………………………………………………………………... 2

Operating the Corning LSE Vortex Mixer………………………………………. 3

Preventative Maintenance ………………………………………………………... 3

Service and Repair Information …………………………………………………. 3

Optional Accessories ……………………………………………………………... 4

Warranty …………………………………………………………………………….. 5

Declaration of Conformity ………………………………………………………... 6

Product Disposal …………………………………………………………………... 7

1



Operating Conditions

The CorningLSEVortex Mixer is designed to be safe under the following conditions:

For indoor use only

Altitude up to 2000 meters

Ambient temperature of 4°C to 65°C

Maximum relative humidity 80% for temperatures up to 31°C then decreasing linearly to 50%

relative humidity at 40°C

Main supply voltage fluctuations not to exceed 10% of the nominal voltage

Installation Category II

Pollution Degree 2

Position at least 30 cm from walls, 30 cm from ceilings and 30 cm between mixers if using

multiple units

2



General Information

The CorningLSEVortex Mixer is a general purpose laboratory vortex mixer. Mixing speed is

adjustable up to 3,000 rpm. A three position switch allows the mixer to be operated continuously or by

“touch” activation. The heavy metal base and rubber feet prevent the unit from “walking” across the

bench, even at maximum speed.

Read this manual thoroughly before attempting to operate the Corning LSE Vortex Mixer. All persons

operating this piece of equipment should review the Safety Precautions section of this manual.

Technical Specifications

Model Catalog

Number Operating

Mode Power

(Volts/Hz/ Amp) Speed

Range

Weight

LSE Vortex

Mixer 120V 6775 Touch or

Continuous 120V/60Hz/0.6 200-3400

rpm 6.0 lbs.

2.5 kg.

LSE Vortex

Mixer 230V

EU Plug

6776 Touch or

Continuous 230V/50Hz/0.3 200-2850

rpm 6.0 lbs.

2.5 kg.

LSE Vortex

Mixer 230V

UK Plug

6777 Touch or

Continuous 230V/50Hz/0.3 200-2850

rpm 6.0 lbs.

2.5 kg.

Unpacking the Corning LSE Vortex Mixer

Upon receipt of the Corning LSE Vortex Mixer, examine the exterior carton for damages. In the event of

shipping damage, a claim must be filed with the transportation carrier within 10 days of receipt. Save all

packaging for inspection by the carrier.

Carefully unpack the unit and check for completeness. Included in the carton should be the following:

Vortex mixer with cup head

Instruction manual

Warranty card

If any of these items are missing, contact Corning Customer Service immediately at:

1.800.492.1110 (for toll-free calling within the U.S. and Canada)

1.978.442.2200 (outside the U.S.), or

Contact your local Corning support office listed on the back cover of this manual.

Save the original packaging until the unit has been shown to be operating properly.

Verify that the unit is rated for the proper voltage by checking electrical / serial no. label on the bottom.

Installation

Locate the mixer on a level, stable surface near a grounded electrical outlet. The surface should be clean

and free of dust to ensure that the feet grip the surface firmly. Allow sufficient clearance on all sides of

the unit for proper ventilation.

With the power switch in the OFF position, plug the power cord into a grounded receptacle.

3



Operating the CorningLSEVortex Mixer

All operating controls are located on the front panel. The power switch, located on the left side of the

panel, has three positions - TOUCH, OFF and ON. When set to the TOUCH position, the mixer is

activated by depressing the mixing head. When pressure is released from the mixing head, operation will

stop. When set to the ON position, the mixer will operate continuously until the switch is moved to either

the OFF or TOUCH position.

The speed control, located on the right side of the panel, is continuously adjustable. Oscillating speed

increases at a nonuniform rate to a maximum of 3,400 rpm (2850 for 230V units) as the knob is turned

clockwise. Before turning on the mixer, set the speed control to the minimum.

To begin operation, move the power switch to either the TOUCH or ON position and turn the speed

control to the desired setting. If the power switch is in the ON position, the shaking head will begin

moving immediately. If the power switch is in the TOUCH position, operation will begin when an object is

placed on the shaking head and slight pressure is applied to depress the head. Shaking will cease when

the object is removed and pressure released.

Preventative Maintenance

Warning: Disconnect CorningLSEVortex Mixer from power source before

attempting any cleaning or maintenance procedures.

After each use, wipe down the mixer with a soft cloth. Do not immerse the unit or pour liquids over it as

electrical shock may occur. Clean up any spills immediately taking the proper precautions. If required,

the shaking head may be removed. First, disconnect the vortexer from the power source and then slowly

pull the shaking head straight up and off the shaking post. The head may then be cleaned with a mild

detergent. Be sure the head is thoroughly dry before replacing on the unit.

The motor and shaking mechanism in the Corning LSE Vortex Mixer requires no routine maintenance or

lubrication. To ensure a long life for the mixer, it should be used in a dry, non-corrosive environment.

Service and Repair Information

If you have a question about the Corning LSEVortex Mixer or have a service inquiry, contact Corning

Customer Service immediately at:

1.800.492.1110 (for toll-free calling within the U.S. and Canada)

1.978.442.2200 (outside the U.S.), or

Contact your local Corning support office listed in the back of this manual.

Before returning any unit for service, a Return Authorization (RA) number must first be obtained.

Equipment sent in without out prior authorization will be returned at the customer’s expense. When

returning a unit to Corning for service, it should be sent in the original packaging. If this is not possible,

be sure that the unit is sufficiently packed. Any damage resulting from improper packaging is the

responsibility of the customer. A written explanation should accompany the unit along with the RA

number.

4



Optional Accessories

Several additional shaking heads are available for the CorningLSEVortex Mixer. To change heads,

disconnect the vortexer from the power source and then remove the vortexing head by slowly peeling it

straight upward off the post. An optional head can then be placed on the post and secured by applying

firm pressure.

Optional shaking heads are as follows:

480100 Optional head, 3 inch, for processing larger numbers of tubes

480101 Optional head for 24 x 1.5/2.0 mL tubes, 24 x 0.5 mL tubes and 32x 0.2

mL tubes (or 4 tube strips)

480102 Optional head for 1 microplate or 64 x 0.2 mL tubes or 8 x 0.2 mL tube

strips

480103 Optional head for 8 x 15 mL and 8 x 12/13 mm diameter tubes

480104 Optional head attachment for 6 x 50 mL tubes

480105 Optional head for 12 x 1.5/2.0 mL tubes, held horizontally

480106 Optional head for 4 x 15 mL tubes, held horizontally

480107 Optional head for 2 x 50 mL tubes, held horizontally

Accessories may be ordered from your Corning dealer or directly from Corning.

5



Warranty Statement

Corning Incorporated (Corning) warrants that this product will be free from defects in material and

workmanship for a period of two (2) years from date of purchase. CORNING DISCLAIMS ALL OTHER

WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. Corning’s sole obligation shall

be to repair or replace, at its option, any product or part thereof that proves defective in material or

workmanship within the warranty period, provided the purchaser notifies Corning of any such defect.

Corning is not liable for any incidental or consequential damages, commercial loss or any other damages

from the use of this product.

This warranty is valid only if the product is used for its intended purpose and within the guidelines

specified in the supplied instruction manual. This warranty does not cover damage caused by accident,

neglect, misuse, improper service, natural forces or other causes not arising from defects in original

material or workmanship. This warranty does not cover motor brushes, fuses, light bulbs, batteries or

damage to paint or finish. Claims for transit damage should be filed with the transportation carrier.

In the event this product fails within the specified period of time because of a defect in material or -

workmanship, contact Corning’s Customer Service at the following numbers: USA: 1-800-492-1110;

Canada: 1-978-442-2200. For other regions of the world, please visit www.corning.com/lifesciences or

see the included instruction manual for a list of World Wide Support Offices.

Corning’s Customer Service team will help arrange local service where available or coordinate a return

authorization number and shipping instructions. Products received without proper authorization will be

returned. All items returned for service should be sent postage prepaid in the original packaging or other

suitable carton, padded to avoid damage. Corning will not be responsible for damage incurred by

improper packaging. Corning may elect for onsite service for larger equipment.

Some states do not allow limitation on the length of implied warranties or the exclusion or limitation of

incidental or consequential damages. This warranty gives you specific legal rights. You may have other

rights which vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend the period

of this warranty.

For your reference, make a note of the serial number, date of purchase and supplier

here.

Serial No. ____________________ Date Purchased _________________

Supplier _____________________________________________________

6



DeclarationofConformity





CorningLifeSciencesherebyconfirmsthattheproduct



CorningLSEVortexMixer



Isinaccordancewiththefollowingdirectivesandstandards:



2006/95/EC LowVoltageDirective

2004/108/EC EMCDirective

98/37/EC MachineDirective

2002/95/EC RoHS

2006/96/EC WEEE



EN61010‐1   

EN61010‐2‐020

EN61326‐1:2006









_____________________________________

QualityManager



Thisequipmenthas

beentestedandfound

tocomplywiththe

limitsforaClassA

digitaldevice,pursuant

tobothPart15ofthe

FCCRulesandtheradio

interferenceregulation

oftheCanadian

Departmentof

Communications.These

limitsaredesignedto

providereasonable

protectionagainst

harmfulinterference

whentheequipmentis

operatedina

commercial

environment.This

equipmentgenerates

usesandcanradiate

radiofrequencyenergy

and,ifnotinstalledand

usedinaccordancewith

theinstructionmanual,

manycauseharmful

interferencetoradio

communications.

Operationofthis

equipmentina

residentialareaislikely

tocauseharmful

interferencewhichcase

theuserwillberequired

tocorrecttheinterface

athisownexpense.



  

7



Product Disposal

This symbol, if present on the product, indicates that the product was planned for use in a country

complying with the Waste Electrical and Electronic Equipment EU Directive, 2002/96/ED. This

symbol indicates that this equipment must not be disposed of with unsorted municipal waste. It is

the product user’s responsibility to correctly dispose of waste equipment by handing it over to an

authorized facility for separate collection and recycling. It is the product user’s responsibility to

decontaminate waste equipment from biological, chemical, and/or radiological hazards prior to

disposal.

Additional information pertaining to the disposal of Corning per the WEEE Directive can be

obtained at www.corning.com/weee.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CORNING Laborausrüstung Handbücher

CORNING

CORNING Spin-X UF 500 Gebrauchsanweisung

CORNING

CORNING Matribot 6150 Bedienungsanleitung

CORNING

CORNING LSE 6780-4 Bedienungsanleitung

CORNING

CORNING Cell Counter Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING Stripettor 4998 Bedienungsanleitung

CORNING

CORNING MicroDEN Bedienungsanleitung

CORNING

CORNING LSE Series Bedienungsanleitung

CORNING

CORNING Axygen Bedienungsanleitung

CORNING

CORNING Axygen Axypet Pro Bedienungsanleitung

CORNING

CORNING PC-611 Bedienungsanleitung

CORNING

CORNING AXYGEN AxySpin R Bedienungsanleitung

CORNING

CORNING LSE 6785-SB Bedienungsanleitung

CORNING

CORNING LSE 6770 Bedienungsanleitung

CORNING

CORNING PC-400D Bedienungsanleitung

CORNING

CORNING Axygen Axypet Bedienungsanleitung

CORNING

CORNING LSE 6875-SB Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING Axygen MotoPet Bedienungsanleitung

CORNING

CORNING Matribot Bioprinter Bedienungsanleitung

CORNING

CORNING Labnet Prism R Bedienungsanleitung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING 6928 Bedienungsanleitung

CORNING

CORNING LSE 6703 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung