CORNING LSE 6703 Bedienungsanleitung

Corning®LSE™

Platform Rockers

Instruction Manual

Catalog Numbers:









Table of Contents

. General Speciications ..........................................................

. Safety Precautions..............................................................

. Installation of the Platform Rocker ..............................................

. Unpacking..................................................................

. Selecting the Location.......................................................

. Adjusting the Angle.........................................................

. Attaching the Power Cord ...................................................

. Installing Double Stacking Platform..........................................

. Operating Instructions..........................................................

. Controls ....................................................................

. Basic Operation.............................................................

. Troubleshooting Guide .........................................................

. Maintenance and Cleaning .....................................................

. Limited Warranty...............................................................

. Equipment Disposal ............................................................

Instruction Manual

1.0 General Specications

Speed Settings  to  tilts/minute

Timer  to  hours or continuous

Motion Rocking

Tilt Angle Fixed °

Maximum Load  lbs. ( kg)

Ambient Operation Range +°C to °C, up to % RH, non-condensing

Dimensions . x . x . in. (. x  x . cm)

Weight . lbs. (. kg)

Electrical

V

V

V ± %, /Hz, .A

V ± %, /Hz, .A

Fuse  x A

Warranty  years

Platform Size . x . in. ( x  cm)

This device is intended for use in a basic electromagnetic environment (Basic, class B), and it is

in compliance with IEC -.

The Corning® LSE™ Platform Rocker is designed to be safe when operated under the following

conditions:

Indoor use

Altitude up to , meters

Pollution Degree 

2.0 Safety Precautions

Do not use the rocker near water. Ensure that water does not get on the device,

particularly during cleaning.

If the unit is used in a manner not speciied in this manual, then the unit may

become unsafe to operate and may void the warranty.

This product must be connected to a grounded power outlet for safe functioning.

Use only the power cord supplied with the product.

The equipment will not restart if the main power source is interrupted.

The equipment will restart in cases of mechanical interruption.

Do not expose the rocker to aggressive vapors (e.g., organic solvents).

Do not insert any objects into the rocker (such as a screwdriver or metal rods).

Never operate the rocker without the platform securely attached.

Hazardous samples should be shaken only in appropriate containment vessels.

2CORNING LSE PLATFORM ROCKERS

Do not rock lammable or explosive samples.

The electrical warning symbol indicates the presence of a potential hazard which

could result in electrical shock.

Do not put your ingers between the rocking platform and the housing. Danger of

mechanical injury.

3.0 Installation of the Platform Rocker

3.1 Unpacking

Before starting the installation, carefully examine the rocker for possible damage or missing parts.

Open the box and carefully remove the padding. Check that the rocker has not been visibly

damaged during transportation. Keep the packing material until you ensure that the rocker

works properly.

Carefully lift the device out of the box.

Be sure that the following information is included on the serial label located on the back of

the unit: serial number, catalog number, electrical rating.

Check that the power cord plug has a pin coniguration that matches a wall socket

according to the local standard.

Should any kind of damage have occurred during transportation, contact the carrier

immediately. The carrier is responsible for shipping damage.

3.2 Selecting the Location

Put the rocker on a horizontal, leveled, and stable surface.

Leave enough space around the rocker for normal air circulation ( in./ cm minimum).

Leave enough space around the rocker for easy access and maintenance.

Avoid locations subject to shocks and vibrations.

Avoid locations subject to frequent power luctuations or power losses, as this may affect

rocker performance.

Select a location that is dry and not subject to drafts or moving air from heating or air

conditioning vents or air blown by other equipment. Plug the unit into a properly grounded

outlet.

Instruction Manual

3.3 Adjusting the Angle

Unload the platform. Locate the knob on the right hand side of the rocker. Note the tilt degree

markings on the platform drive rod (front center under platform). Loosen knob on the side by

rotating counterclockwise. Adjust the platform to desired tilt angle. Retighten the knob on

the side by turning clockwise. Test the unit without load to ensure platform is tight.

NOTE: You many need to turn the rocker on and off to change drive rod position before adjusting.

3.4 Attaching the Power Cord

Connect the main power cord to the rocker and then connect the plug end of the cord to a

grounded wall socket. Avoid lines to which powerful electric motors, refrigerators, and similar

devices are connected.

Be careful when you plug the cord to a grounded wall socket. Do not touch plug

with wet hands. Do not pull the plug by the cord.

3.5 Installing Double Stacking Platform

. Set the posts (A) through the  holes at the corners of the bottom platform.

. Add a washer (B) and nut (C) to each post.

. Fit the upper platform (D) on the top of the  posts through the corner holes.

. Screw on the  metal knurl nuts (E) to secure the upper platform.

NOTE: Misuse or unauthorized modiications will waive the warranty rights. If the equipment

is used in a manner not speciied by the manufacturer, the safety features of the rocker may

be impaired.

4CORNING LSE PLATFORM ROCKERS

4.0 Operating Instructions

4.1 Controls

1. POWER switch: Turns the rocker ON (power switch illuminates) or OFF

2. SPEED knob: Sets the rocker speed

3. TIME knob: Sets the time of the rocker

4. HOLD yellow light: Illuminates when the rocker is set for continuous running

5. START/STOP button: START or STOP rocking

6. RUN green light: Illuminates when the rocker is running

4.2 Basic Operation

Switch on POWER.

Set SPEED knob on desired value.

Set TIME knob on desired value or on HOLD – continuous function (yellow light next to

HOLD will illuminate).

Press START/STOP button to start rocking.

Press START/STOP button to stop rocking (HOLD position). Device automatically stops after

the set time passes. Note: Pressing the START/STOP button during operation will reset the

timer.

5.0 Troubleshooting Guide

Be sure to disconnect the rocker from the main power source immediately in case of any signs

of malfunction and contact Corning Customer Service at .. or ...

Problem Solution

Power switch does not light up Check the power connection. Check the fuses.

Contact Corning Customer Service.

Rocker does not start Check the power connection. Check the fuses.

Contact Corning Customer Service.

Instruction Manual

6.0 Maintenance and Cleaning

No routine maintenance or lubrication is required.

It is recommended that the rocker be kept clean to ensure a long, trouble-free operation.

The outside housing of the platform rocker may be cleaned with a soft, damp cloth when

needed. Do not use any aggressive or abrasive cleaners (acetone, nitro, polish, etc.), as they

may permanently damage the rocker inish.

Before cleaning the rocker, always unplug the power cord from the wall socket.

Make sure the rocker is switched off before installing an additional platform.

7.0 Limited Warranty

Corning Incorporated (Corning) warrants that this product will be free from defects in

material and workmanship for a period of ive () years from date of purchase. CORNING

DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.

Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof

that proves defective in material or workmanship within the warranty period, provided the

purchaser notiies Corning of any such defect. Corning is not liable for any incidental or

consequential damages, commercial loss, or any other damages from the use of this product.

This warranty is valid only if the product is used for its intended purpose and within the

guidelines speciied in the supplied instruction manual. This warranty does not cover damage

caused by accident, neglect, misuse, improper service, natural forces, or other causes not

arising from defects in original material or workmanship. This warranty does not cover motor

brushes, fuses, light bulbs, batteries, or damage to paint or inish. Claims for transit damage

should be iled with the transportation carrier.

In the event this product fails within the speciied period of time because of a defect in

material or workmanship, contact Corning’s Customer Service at ... Outside the

United States, call +... or contact your local Corning sales ofice.

Corning Customer Service will help arrange local service where available or coordinate a return

authorization number and shipping instructions. Products received without proper authorization

will be returned. All items returned for service should be sent postage prepaid in the original

packaging or other suitable carton, padded to avoid damage. Corning will not be responsible for

damage incurred by improper packaging. Corning may elect for onsite service for larger equipment.

Some states do not allow limitation on the length of implied warranties or the exclusion

or limitation of incidental or consequential damages. This warranty gives you speciic legal

rights. You may have other rights which vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation of liability, or

extend the period of this warranty.

For your reference, make a note of the serial and model number, date of purchase, and supplier here.

Model No. ____________________________________ Serial No. __________________________________

Date Purchased ________________________________ Supplier ___________________________________

8.0 Equipment Disposal

According to Directive //EU of the European Parliament and Council of th

July  on waste and electronic equipment (WEEE) as amended, the Corning®

LSE™ Platform Rockers are marked with the crossed-out wheeled bin and must

not be disposed of with domestic waste.

Consequently, the buyer shall follow the instructions for reuse and recycling of

waste electronic and electrical equipment (WEEE) provided with the products and

available at www.corning.com/weee.

Warranty/Disclaimer: Unless otherwise specied, all products are for research use or general

laboratory use only.* Not intended for use in diagnostic or therapeutic procedures. Not for use in

humans. These products are not intended to mitigate the presence of microorganisms on surfaces

or in the environment, where such organisms can be deleterious to humans or the environment.

Corning Life Sciences makes no claims regarding the performance of these products for clinical or

diagnostic applications. *For a listing of US medical devices, regulatory classications or specic

information on claims, visit www.corning.com/resources.

For a listing of trademarks, visit www.corning.com/clstrademarks. All other trademarks are the property of their respective owners.

Corning Incorporated

Life Sciences

www.corning.com/lifesciences

NORTH AMERICA

t 800.492.1110

t 978.442.2200

ASIA/PACIFIC

Australia/New Zealand

t 61 427286832

Chinese Mainland

t 86 21 3338 4338

India

t 91 124 4604000

Japan

t 81 3-3586 1996

Korea

t 82 2-796-9500

Singapore

t 65 6572-9740

Taiwan

t 886 2-2716-0338

EUROPE

CSEur[email protected]

France

t 0800 916 882

Germany

t 0800 101 1153

The Netherlands

t 020 655 79 28

United Kingdom

t 0800 376 8660

All Other European

Countries

t +31 (0) 206 59 60 51

LATIN AMERICA

grupoL[email protected]

Brazil

t 55 (11) 3089-7400

Mexico

t (52-81) 8158-8400

Andere Handbücher für LSE 6703

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CORNING Laborausrüstung Handbücher

CORNING

CORNING Matribot Bioprinter Bedienungsanleitung

CORNING

CORNING LSE 6780-4 Bedienungsanleitung

CORNING

CORNING Axygen Bedienungsanleitung

CORNING

CORNING 6928 Bedienungsanleitung

CORNING

CORNING LSE 6755 Bedienungsanleitung

CORNING

CORNING Spin-X UF 6 Gebrauchsanweisung

CORNING

CORNING LSE 6709 Bedienungsanleitung

CORNING

CORNING Lambda EliteMax Bedienungsanleitung

CORNING

CORNING Matribot Bioprinter Bedienungsanleitung

CORNING

CORNING Matribot 6150 Bedienungsanleitung

CORNING

CORNING Lambda Plus Bedienungsanleitung

CORNING

CORNING Lambda EliteTouch Bedienungsanleitung

CORNING

CORNING LSE 6775 - 120V US Bedienungsanleitung

CORNING

CORNING PC-400D Bedienungsanleitung

CORNING

CORNING Labnet Prism R Bedienungsanleitung

CORNING

CORNING Axygen Axypet Pro Bedienungsanleitung

CORNING

CORNING CamSplice FBC-017 Bedienungsanleitung

CORNING

CORNING SCF-1296 Bedienungsanleitung

CORNING

CORNING MicroDEN Bedienungsanleitung

CORNING

CORNING AXYGEN AxySpin R Bedienungsanleitung

CORNING

CORNING Axygen Axypet Bedienungsanleitung

CORNING

CORNING LSE 6703 Bedienungsanleitung

CORNING

CORNING Gosselin S-Blender 1 Produktinformationsblatt

CORNING

CORNING PC-611 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung