Craftsman SNOW BLADE 486.24441 Bedienungsanleitung

Operator's Manual

42" SNOW BLADE

Model No.

486.24441

PRINTED IN U.S.A.

FORM NO. 49795 (REV. 2 12/05)

CAUTION:

Before using this prod uct, read

and follow all Safety, Assembly

and Operating Instructions

• Safety

• Assembly

• Operation

• Maintenance

• Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

IMPORTANT:

For Missing Parts or

Assembly Questions Call 866-576-8388

TABLE OF CONTENTS

MODEL NUMBER: 486.24441

SERIAL NUMBER: __________________

DATE OF PURCHASE: __________________

The model number and serial numbers will be found on

a decal attached to the snow blade.

You should record both the serial number and the

date of purchase and keep in a safe place for future

reference.

SERVICE AND ADJUSTMENTS....................................13

STOR AGE.................................................................13

TROU BLE SHOOT ING...............................................14

REPAIR PARTS ILLUSTRATION......................................18

REPAIR PARTS LIST................................................19

PARTS ORDERING/SERVICE...............BACK COV ER

Look for this symbol to point out important safety precautions. It means —

Attention!! Become

alert!! Your safety is involved.

SAFETY

WARRANTY

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Snow Blade fails due to a defect in

material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair (or

replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

WARRANTY

....................................................................

SAFETY RULES

.............................................................

AC CES SO RIES AND ATTACHMENTS

..........................

FULL SIZE HARDWARE CHART

...................................

CARTON CONTENTS

....................................................

ASSEMBLY

................................................................

5-10

OPERATION

............................................................

11-12

MAIN TE NANCE

............................................................

1. Read the tractor and snow blade owner's manuals

and know how to operate your tractor before using

tractor with snow blade attachment.

2. Never operate tractor and snow blade without wearing

proper clothing suited to weather conditions and

operation of controls.

3. Never allow children to operate tractor and snow

blade, and do not allow adults to operate without

proper instructions.

4. Always begin with transmission in ﬁ rst (low) gear and

gradually increase speed as conditions permit.

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the

equipment. Exercise caution at all times when using power equipment.

ACCESSORIES AND ATTACHMENTS

FULL SIZE HARDWARE CHART

WHEEL

WEIGHT

TIRE CHAINS

WEIGHT BR

CKET

FOR DR

AW A

W CAB

REF. QTY. DESCRIPTION

A 1 Hex Bolt, 1/4-20 x 3-1/4" LG.

B 1 Hex Bolt 1/4-20 x 1-1/2"

C 1 Hex Bolt, 5/16-18 x 1-1/2"

D 14 Hex Bolt, 3/8-16 x 1"

E 2 Carriage Bolt, 3/8 x 1-1/4"

F 2 Carriage Bolt, 5/16 x 1"

G 6 Hex Bolt, 3/8" x 1" (Thread Forming)

H 6 Carriage Bolt, 3/8" x 1"

I 2 Hex Jam Nut, 5/16-24 Thread

J 3 Nylock Hex Nut, 1/4-20 Thread

K 3 Nylock Hex Nut, 5/16-18 Thread

L 16 Nylock Hex Nut, 3/8-16 Thread

M 6 Large 1/2" Washer

N 6 3/8" Flat Washer

O 4 Hairpin Cotter

P 2 Cotter Pin 1/8" x 1-1/4"

Q 1 1/2" Washer

R 6 Lock Washer, 3/8"

S 2 Palnut, 3/8"

T 1 Spacer, 9/16" OD x 5/8" LG.

U 2 Spacer, 9/16" OD x 1" LG.

A B

SPECIAL

USE ONLY

These and other accessories are recommended for use with your unit. Call 1-800-4-MY-HOME® to ﬁ nd out if they are available.

If available, they may be purchased at most Craftsman outlets or by calling 1-800-4-MY-HOME®.

REF. QTY. DESCRIPTION

12 1 Hanger Bracket, L.H.

13 1 Hanger Bracket, R.H.

14 1 Pivot Support Bracket

15 2 Angle Support Bracket

16 1 Channel Assembly

17 1 Blade Assembly

18 1 Blade Pivot Rod

19 1 Lift Handle Tube

20 1 Lift Handle Rod

21 1 Cable

REF. QTY. DESCRIPTION

1 2 Cable End Fitting

2 1 Cable Mount Bracket

3 1 Angle Lock Spring

4 2 Nylon Tie

5 1 Spring Mount Rod

6 1 Channel Pivot Pin

7 1 Blade Adjust Spring

8 1 Plastic Grip

9 1 Grip Assembly

10 2 Angle Lock Bars

11 1 Blade Pivot Shaft

REF. QTY. DESCRIPTION

7 1 Blade Adjust Spring

8 1 Plastic Grip

9 1 Grip Assembly

10 2 Angle Lock Bars

11 1 Blade Pivot Shaft

REF. QTY. DESCRIPTION

7 1 Blade Adjust Spring

8 1 Plastic Grip

9 1 Grip Assembly

10 2 Angle Lock Bars

11 1 Blade Pivot Shaft

REF. QTY. DESCRIPTION

1 2 Cable End Fitting

2 1 Cable Mount Bracket

3 1 Angle Lock Spring

4 2 Nylon Tie

5 1 Spring Mount Rod

6 1 Channel Pivot Pin

REF. QTY. DESCRIPTION

1 2 Cable End Fitting

2 1 Cable Mount Bracket

3 1 Angle Lock Spring

4 2 Nylon Tie

5 1 Spring Mount Rod

6 1 Channel Pivot Pin

REF. QTY. DESCRIPTION

1 2 Cable End Fitting

2 1 Cable Mount Bracket

3 1 Angle Lock Spring

4 2 Nylon Tie

5 1 Spring Mount Rod

6 1 Channel Pivot Pin

PARTS IN PACKAGES NOT SHOWN FULL SIZE

CARTON CONTENTS

(Loose Parts in Carton)

REF. QTY. DESCRIPTION

12 1 Hanger Bracket, L.H.

13 1 Hanger Bracket, R.H.

14 1 Pivot Support Bracket

15 2 Angle Support Bracket

16 1 Channel Assembly

REF. QTY. DESCRIPTION

12 1 Hanger Bracket, L.H.

13 1 Hanger Bracket, R.H.

14 1 Pivot Support Bracket

15 2 Angle Support Bracket

16 1 Channel Assembly

REF. QTY. DESCRIPTION

17 1 Blade Assembly

18 1 Blade Pivot Rod

19 1 Lift Handle Tube

20 1 Lift Handle Rod

21 1 Cable

REF. QTY. DESCRIPTION

17 1 Blade Assembly

18 1 Blade Pivot Rod

19 1 Lift Handle Tube

20 1 Lift Handle Rod

21 1 Cable

ASSEMBLY

(1) Pliers

(1) Hammer

(1) Adjustable Wrench (or socket set)

(1) 9/16" Open End or Box End Wrench

(1) 7/16" Open End or Box End Wrench

(1) 1/2" Open End or Box End Wrench

TOOLS REQUIRED FOR ASSEMBLY

STEP 1: (SEE FIGURE 1)

• Look under the front of your tractor. If there is a single

mower deck suspension bracket located underneath

the middle of the front axle, continue on to step 2. If

your tractor does not have a mower deck suspension

bracket underneath the middle of the front axle, skip

to step 4 on page 6 for tractors with dual suspension

brackets.

MOWER DECK

SUSPENSION

BRACKET

FIGURE 1

• Remove all parts and hardware packages from the

carton. Lay out parts and hardware and identify using

the illustrations on pages 3 and 4.

NOTE:

Not all of the supplied parts and hardware will be

needed for one particular tractor. Unneeded items may be

discarded after assembly has been completed.

NOTE:

Right hand (RH) and left hand (LH) are

determined from the operator's position while seated on

the tractor.

CAUTION: Do not

begin assembling until

the tractor engine, mufﬂ er and exhaust

deﬂ ector have been allowed to cool off.

REMOVE

BROWNING

SHIELD

FIGURE 2

FIGURE 3

5/16" NYLOCK

NUT (K)

3/8" NYLOCK

NUT (L)

5/16" x 1"

CARRIAGE

BOLT (F)

ENGINE

MOUNTING

PLATE

1/2" LARGE

WASHER (M)

(IF NEEDED)

3/8" x 1" CARRIAGE

BOLT (H)

STEP 2: (SEE FIGURE 2)

•

Remove the tractor hood. Refer to your tractor owners

manual for instructions on how to properly remove the

hood.

• Remove the browning shield from the front of the

tractor as shown. Hold onto the shield as you remove

the second bolt to prevent it from falling.

NOTE:

Reinstall the browning shield before using your

tractor.

INSTRUCTIONS FOR TRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKET

STEP 3: (SEE FIGURE 3)

• Fasten the R.H. hanger bracket (bend facing out)

to the holes indicated in the tractor frame. If there

is an engine mounting plate like the one drawn with

dotted lines, use large 1/2" ﬂ at washers (M) as shims

between the hanger bracket and the tractor frame in

the locations shown. In the front three holes use three

3/8" x 1" carriage bolts (H), two large 1/2" washers

(M) if needed, and three 3/8" nylock nuts (L). In the

rear hole use a 5/16" x 1" carriage bolt (F), a large

1/2" washer (M) if needed, and a 5/16" nylock nut (K).

Tighten all bolts. Repeat for the L.H. hanger bracket.

• Reinstall the browning shield then

go to step 9

page 7.

FIGURE 4

STEP 4: (SEE FIGURE 4)

• Compare your tractor to the illustrations shown in

ﬁ gure 4. If your tractor resembles the top illustration,

go to step 5. If your tractor resembles the bottom

illustration, go to step 7.

FRONT SUSPENSION

BRACKET

FRONT SUSPENSION

BRACKET

REMOVE BOLTS FROM THESE HOLES

FRONT

SUSPENSION

BRACKET

FIGURE 5

INSTRUCTIONS FOR TYPE A TRACTORS

STEP 5:

(SEE FIGURE 5)

• Remove any bolts found in the holes indicated in the

illustration.

FIGURE 6

3/8" x 1"

HEX BOLT (D)

3/8" LOCK

WASHER (L)

3/8" FLAT

WASHER (N)

1/2" LARGE

WASHER (M)

R.H. HANGER

BRACKET

STEP 6: (SEE FIGURE 6)

• Attach the R.H. hanger bracket to the two front empty

holes on the right side of the tractor frame using two

new 3/8" x 1" hex bolts (D), 3/8" lock wash ers (L), and

3/8" ﬂ at washers (N) as shown. For the rear hole, use

a 3/8" x 1" hex bolt (D), 3/8" lock washer (L) and 3/8"

ﬂ at washer (N) with a large 1/2" washer (M) placed

between the hanger bracket and the tractor frame.

Tight en.

Repeat for the left side.

• Skip to step 9.

FIGURE 7

REMOVE BOLTS FROM

THESE HOLES

FRONT

SUSPENSION

BRACKET

INSTRUCTIONS FOR TYPE B TRACTORS

STEP 7: (SEE FIGURE 7)

• Remove any bolts found in the holes indicated in the

illustration.

INSTRUCTIONS FOR TRACTORS WITH DUAL

FRONT DECK SUSPENSION BRACKETS

TYPE A

TYPE B

STEP 8: (SEE FIGURE 8)

•

Attach the R.H. hanger bracket to the three holes shown

on the side of the tractor frame using three 3/8" x 1" hex

bolts (D), 3/8" lock washers (R) and 3/8" ﬂ at washers (N).

Use 3/8" nylock nuts (L) on inside of frame if bolts insert

freely into holes.

Tight en.

• Repeat for other side.

NOTE:

Use special 3/8" x 1" thread forming bolts (G) in any

holes that are too small for regular bolts.

INSTRUCTIONS FOR ALL TRACTORS

FIGURE 10

FIGURE 8

3/8" x 1" HEX BOLT (D)

(OR THREAD FORMING

BOLT (G) IF NEEDED)

3/8" LOCK

WASHER (R)

3/8" FLAT

WASHER (N)

3/8" NYLOCK NUT (L)

(IF NEEDED)

R.H. HANGER

BRACKET

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT (L)

PIVOT SUPPORT

BRACKET

FIGURE 9

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT (L)

ANGLE SUPPORT

BRACKET

STEP 10: (SEE FIGURE 10)

• Assemble the pivot support bracket to the angle

support brackets using four 3/8" x 1" hex bolts (D) and

four 3/8" nylock nuts (L).

Do not tighten yet.

•

Tighten

the 4 bolts fastening the angle support

brackets to the hanger brackets.

•

Tighten

the 4 bolts fas ten ing the pivot support bracket

to the angle support brackets.

(Right Hand Side View)

FIGURE 11

STEP 11: (SEE FIGURE 11)

• Assemble the two angle lock bars together as shown

in ﬁ gure 6, so that all holes are aligned. Use one 3/8"

x 1-1/4" carriage bolt (E) and one 3/8" nylock nut (L).

Be sure to insert bolt from side indicated.

Do not

tighten at this time.

•

Hold the angle lock bars so that the square holes are

at the top. Insert the straight hook end of the angle

lock spring through the small middle hole in both

angle lock bars.

3/8" x 1-1/4"

CARRIAGE BOLT (E)

3/8" NYLOCK NUT (L)

ANGLE LOCK

BARS

ANGLE LOCK SPRING

STEP 9: (SEE FIGURE 9)

•

Assemble one angle support bracket to the topmost

set of holes in the hanger brackets using two 3/8" x

1" hex bolts (D) and 3/8" nylock nuts (L). Assemble

the second angle support bracket to the second from

the bottom set of holes in the hanger brackets using

two 3/8" x 1" hex bolts (D) and 3/8" nylock nuts (L).

Be sure the brackets are turned as shown.

Do not

tighten yet.

STEP 12: (SEE FIGURE 12)

• Insert the round hook end of the angle lock spring up

through the hole in the spring mount bracket.

• Insert the angle lock bars down through the slot in

the channel. Underneath the channel, place a 1" long

spacer (U) on each side of the angle lock bars and

insert a 1/4" x 3-1/4" bolt (A) through the chan nel,

angle lock bars and the spacers. Secure the bolt with

a 1/4" nylock nut (J).

Tighten

so that lock bars can

pivot freely.

• At this time

tighten

the 3/8" carriage bolt and hex nut

previously assembled to angle lock bars.

NOTE:

When the angle lock bars are pulled back in slot,

the pivot plate should unlock and be free to pivot to the

right or left position.

1/4" x 3-1/4"

HEX BOLT (A)

1" SPACERS (U)

1/4" NYLOCK

NUT (J)

PIVOT

PLATE

ANGLE

LOCK

SPRING

MOUNT

BRACKET

CHANNEL

(Right Hand Side View)

FIGURE 12

(Top View)

FIGURE 13

STEP 13: (SEE FIGURE 13)

• Using a hammer, assemble a 3/8" palnut (S) onto one

end of the spring mount rod. Insert the other end of

the spring mount rod through the pivot plate using the

rear set of holes. Support the as sem bled end of the

spring mount rod on a block of wood, and assemble

the remaining palnut onto the other end of the rod.

3/8" PALNUT (S)

PIVOT

PLATE

SPRING

MOUNT

ROD

3/8" PALNUT (S)

STEP 14: (SEE FIGURE 14)

• Assemble a 3/8" x 1-1/4" carriage bolt (E) through the

square hole in the cable mount bracket and through

the square hole in the angle lock bars. (The carriage

bolts should face in opposite directions.) Using pliers

hold the cable mount brack et in po si tion, angling down

to wards the L.H. hole in the channel as shown in

ﬁ gure 15. Secure with a 3/8" nylock nut (L).

Tighten.

Refer to the ﬁ gure for the correct angle for the cable

mount bracket.

FIGURE 14

(Right Hand Side View)

3/8" x 1-1/4"

CARRIAGE BOLT (E)

3/8" NYLOCK

NUT (L)

ALIGN CABLE

MOUNT BRACKET

WITH L.H. HOLE ANGLE

LOCK

BARS

FRONT

STEP 15: (SEE FIGURE 15)

• Assemble one 5/16" jam nut (I) approximately 3/4"

onto thread ed end of control cable that has no rubber

cap or preassembled nuts. Assemble threaded cable

end through round hole in cable mount bracket and

secure with another 5/16" jam nut (I).

Tight en

NOTE:

Some adjustment of jam nuts may be required

after blade assembly is completed.

CHANNEL ASSEMBLY

5/16" JAM

NUT (I)

5/16" JAM

NUT (I)

CABLE MOUNT

BRACKET

REAR

3/4"

FIGURE 15 (Left Hand Side View)

FIGURE 18 (Right Hand Side View)

STEP 16: (SEE FIGURE 16)

• Assemble ball end of control cable up through hole in

cable end ﬁ tting and pull until ball slips inside curled

edge of ﬁ tting. If ball won't slip under edge of curl, it

will need to be inserted through open end of curl.

•

Assemble 1/4" x 1-1/2" (B) hex bolt down through the

cable end ﬁ tting, the 5/8" long spacer (T) and the left

hand hole in the channel assembly. Secure with a

1/4" nylock nut (J).

Tighten.

NOTE:

Make sure the cable mount bracket is aligned

with the cable end ﬁ tting to prevent binding of cable. The

other end of the control cable will be at tached in a later

step.

FIGURE 16 (Left Hand Side View)

STEP 17: (SEE FIGURE 17)

• To attach the blade to the channel assembly, align

the notched holes in the pivot plate with the notched

holes in the blade. Insert a 1/8" x 1-1/4" cotter pin (P)

down through the hole at the bend in the blade pivot

shaft. Spread the ends of the pin. From the left side

insert the blade pivot shaft, bend facing top of blade,

through the notched holes. Secure the shaft with

another 1/8" x 1-1/4" cotter pin (P) through the end

hole in the shaft. Spread the ends of the pin.

• Remove the plastic cap and one 3/8" hex nut from the

bolt in the blade adjust spring. Adjust the re main ing

3/8" hex nut down approximately 1" onto the bolt

threads. Hook the spring over the spring mount rod.

Place the bolt up through the hole in the top edge of

the blade and reassemble the other 3/8" hex nut to

the bolt and tighten down against the top edge of the

blade. Re place the plastic cap over the end of the bolt

threads.

STEP 18: (SEE FIGURE 18)

• Assemble the large 1/2" washer (Q) onto the channel

pivot pin.

• Attach the chan nel as sem bly to the tractor by placing

the end of the chan nel as sem bly up inside the pivot

support brack et on the tractor. Align the hole in the

pivot support bracket with the second hole from the

end in the channel assembly. Insert the channel pivot

pin through the aligned holes from the left side and

secure with a hairpin cotter (O).

(Right Hand Side View)

FIGURE 17

3/8" HEX NUT

(TOP)

PLASTIC

CAP

3/8" HEX NUT

(BOTTOM)

BLADE

1/8" x 1-1/4"

COTTER PIN (P)

BLADE

PIVOT

SHAFT

SPRING

MOUNT

ROD

BLADE

ADJUST

SPRING

1/8" x 1-1/4"

COTTER PIN (P)

PIVOT PLATE

NOTCHED HOLE

HAIRPIN

COTTER (O)

PIVOT SUPPORT

BRACKET CHANNEL

PIVOT PIN

CHANNEL

ASSEMBLY

1/2" WASHER (Q)

CHANNEL

ASSEMBLY

HOLE

1/4" x 1-1/2"

HEX BOLT (B)

CABLE END

FITTING

1/4" NYLOCK

NUT (J)

5/8" SPACER (T)

CHANNEL

ASSEMBLY

HOLE

REAR

FIGURE 20 (Right Hand Side View)

STEP 19: (SEE FIGURE 19)

• From the left side, insert the welded end of the lift

handle rod through the hole in the end of the chan nel

as sem bly (Figure 18). Next, insert the lift link pin

through the hole in the bracket that is welded to the lift

handle rod. (The lift link is pre-assembled to the pivot

support bracket). Se cure the bracket with a hairpin

cotter (O) in sert ed up through the lift link pin.

• Using the furnished grease packet, apply a light

coating of grease to the straight upper portion of the

lift handle rod. Slide the lift handle tube onto the rod.

STEP 20: (SEE FIGURE 20)

•

Remove the rubber cap and

the ﬁ rst

jam nut from the

threaded end of the control cable and slide them onto

the control cable wire. Adjust the second jam nut on

the threads so that it is approximately 3/4" from end.

Assemble threaded end of cable through the cable

mount bracket and

secure it with the ﬁ rst jam nut.

Reinstall the rubber cap onto the t

readed cable end.

NOTE:

Some adjustment of jam nuts may be required

after blade assembly is completed.

RUBBER

CAP

CABLE MOUNT BRACKET

JAM NUTS

3/4"

CONTROL CABLE END

FIGURE 19

(Left Hand Side View)

LIFT HANDLE ROD

HAIRPIN COTTER (O)

LONG PIN

(LIFT LINK)

WELDED BRACKET

LIFT HANDLE TUBE

FIGURE 22

(Left Hand Side View)

STEP 21: (SEE FIGURE 21)

• Assemble plastic grip onto lock release grip assembly.

• Attach lock release grip assembly to lift handle tube

using one 5/16" x 1-1/2" hex bolt (C) and one 5/16"

nylock nut (K).

Do not overtighten

the nut. The grip

as sem bly must pivot freely.

• Assemble the ball end of the cable to a cable end

ﬁ tting as you did to the other end of the cable. Secure

the cable end ﬁ tting to the weld bolt on the lock release

grip with a 1/4" nylock nut (J).

Do not over tight en

the

lock nut. The cable ﬁ t ting must pivot freely.

STEP 22: (SEE FIGURE 22)

• Place the end of the blade pivot rod down through the

blade pivot shaft. Attach the other end of the blade

pivot rod to the lift handle tube. Secure both ends with

a hairpin cotter (O). The holes for the hairpin cotters

should be parallel to the ground.

• Use the two plastic ties to hold the cable se cure ly

to the outside of the handle tube and away from the

tractor to avoid direct heat from the tractor mufﬂ er.

• Squeeze the grip assembly to check blade pivot. To

adjust, see Service & Adjustments section on p. 13.

FIGURE 21

(Right Hand Side View)

5/16" x 1-1/2"

HEX BOLT (C)

PLASTIC

GRIP

LOCK RELEASE

GRIP ASSEMBLY

1/4" WELD

BOLT

CABLE END

FITTING

5/16" NYLOCK

NUT (K)

1/4" NYLOCK

NUT (J)

CABLE

CABLE END

FITTING

CABLE END

FITTING

BLADE PIVOT

ROD LIFT HANDLE

TUBE

BLADE

PIVOT SHAFT

HAIRPIN

COTTER (O)

HAIRPIN COTTER (O)

PLASTIC TIES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 486.243291 Bedienungsanleitung

Craftsman

Craftsman 650 Series Bedienungsanleitung

Craftsman

Craftsman 247.24019.1 Bedienungsanleitung

Craftsman

Craftsman 486.254072 Bedienungsanleitung

Craftsman

Craftsman 486.24449 Bedienungsanleitung

Craftsman

Craftsman 316.792520 Bedienungsanleitung

Craftsman

Craftsman 855000CM Bedienungsanleitung

Craftsman

Craftsman C944.518321 Bedienungsanleitung

Craftsman

Craftsman 610.24489 Bedienungsanleitung

Craftsman

Craftsman 358.792410 Bedienungsanleitung

Craftsman

Craftsman 486.24414 Bedienungsanleitung

Craftsman

Craftsman 358.796340 Bedienungsanleitung

Craftsman

Craftsman 486.24839 Bedienungsanleitung

Craftsman

Craftsman 3One 917.257562 Bedienungsanleitung

Craftsman

Craftsman 316.792440 Bedienungsanleitung

Craftsman

Craftsman 358.795740 Bedienungsanleitung

Craftsman

Craftsman 358.797110 Bedienungsanleitung

Craftsman

Craftsman 917.248961 Bedienungsanleitung

Craftsman

Craftsman 917.248910 Bedienungsanleitung

Craftsman

Craftsman 486.244412 Bedienungsanleitung

Craftsman

Craftsman 486.244411 Bedienungsanleitung

Craftsman

Craftsman 486.244021 Bedienungsanleitung

Craftsman

Craftsman 240.74801 Bedienungsanleitung

Craftsman

Craftsman 486.24326 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung