CYP CH-1527TX Bedienungsanleitung

CH-1527TX & RX

HDMI over CAT5e/6/7 Extender with LAN/IR/RS-232/

PoE

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.0 January 2012

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 21/01/16 Preliminary Release

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6.1 Transmitter Front and Rear Panels..3

6.2 Receiver Front and Rear Panels .....4

6.3. IR Cable Pin Assignment.................5

6.4. D-Sub 9 Pin Denitions ....................5

7. Connection Diagram ............................ 6

8. Specications ........................................ 7

8.1 CAT5e/6/7 Cable Specication .....8

8.2 Timing Support Chart .......................8

9. Acronyms ............................................... 9

1. INTRODUCTION

The HDMI over single CAT5e/6/7 Transmitter and Receiver set can

send uncompressed audio/video and IP data over a single run of

CAT5e/6/7 cable at a distance up to 100 meter. It has the added

benet of control through the built-in RS-232 and IR ports and a bi-

directional LAN serving connection. The Receiver (PD) can be

greater exibility in installations.

2. APPLICATIONS

• 48V PoE from Transmitter (PSE) to Receiver (PD)

• Household entertainment sharing and control

• Lecture room display and control

• Showroom display and control

• Meeting room presentation and control

• Classroom display and control

3. PACKAGE CONTENTS

• 1×HDMI to CAT5e/6/7 (with LAN/IR/RS-232) Transmitter

• 1×CAT5e/6/7 to HDMI (with LAN/IR/RS-232) Reciever

• 1×IR Blaster

• 1×IR Extender

• 1×48 V/0.83 A DC Power Adaptor

• Operation Manual

4. SYSTEM REQUIREMENTS

Input source equipment such as PS3/Blu-ray player and output HD TV/

display.

5. FEATURES

• HDMI with 3D, 4K2K support, HDMI & DVI Compliant

• Supports CEC bypass

• Simultaneous transmission of uncompressed data over a single

100m/328ft CAT5e/6/7 cable

• 5Play™ convergence: HDMI, LAN, PoE & Control (IR & RS-2232)

• Supports resolution up to 4K2K@50/60 & YUV_420 and 21:9

• Supports standard 48V from Transmitter (PSE) to Receiver (PD)

• Installation Friendly

• Supports HDMI Input/Output cable distance up to 5m at

4K2K@50/60 & YUV_420

Note:

1. The standard 48V PoE function is designed for powering

compatible Receiver units only---non-PoE Receivers will need

their own power supply. Receivers of another brand may not be

compatible.

2. Displaying HDMI 3D and 4K2K contents, equivalent source signal

and HDMI cable are required in order to secure the quality.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Transmitter Front and Rear Panels

POWER

LINK

RS-232 IN

STD UPDATE

LAN

6 7 8 109

CAT5e/6/7 OUT

IR2

EXTENDER

HDMI IN

DC 48V

IR1

BLASTER

1 3 4 52

RearFront

DC 48V: Plug the 48V DC power supply into the unit and connect

the adaptor to an AC outlet.

IR1 BLASTER: Connect to the supplied IR Blaster cable for IR signal

transmission. Place the IR Blaster in direct line-of-sight of the

equipment to be controlled.

IR2 EXTENDER: Connect to the supplied IR Extender cables for IR

signal reception. Ensure that remote being used is within the direct

line-of-sight of the IR Extender.

CAT5e/6/7 OUT: Connect to the Receiver unit with a single

CAT5e/6/7 cable for transmission of all data signals.

HDMI IN: Connect to HDMI source equipment such as a DVD or

Blu-ray player.

STD/UPDATE Switch: This switch is reserved for factory use only.

RS-232 IN: Connect to a PC or Laptop with D-Sub 9-pin male cable

for the transmission of RS-232 commands.

LAN: Connect to an internet or network system.

POWER LED: This LED will illuminate when the device is connected

to a power supply.

LINK LED: This LED will illuminate when both Transmitter and Receiver

are connected through CAT cable. When it blinks regularly it

states the Transmitter is NOT sending signal but the Transmitter and

Receiver are linked and if it blinks irregularly it states an error has

occurred.

6.2 Receiver Front and Rear Panels

CAT5e/6/7 IN

IR1

EXTENDER

HDMI OUT

IR2

BLASTER POWER

LINK

RS-232 OUT

LAN

STD UPDATE

1 42 3

RearFront

6 7 8 95

IR2 BLASTER: Connect to the supplied IR Blaster cable for IR signal

transmission. Place the IR Blaster in direct line-of-sight of the

equipment to be controlled.

IR1 EXTENDER: Connect to the supplied IR Extender cables for IR

signal reception. Ensure that remote being used is within the direct

line-of-sight of the IR Extender.

CAT5e/6/7: Connect to the Transmitter unit with a single CAT5e/6/7

cable for transmission of all data signals.

HDMI OUT: Connect to a HDMI equipped TV/monitor for display of

the HDMI input source signal.

STD/UPDATE Switch: This switch is reserved for factory use only.

RS-232 OUT: Connect to the device that is to be controlled (via

D-Sub 9-pin female cable) by RS-232 commands.

LAN: Connect to a PC or Laptop to utilize the Internet or network

function.

POWER LED: This LED will illuminate when the device is connected

to a power supply.

LINK LED: This LED will illuminate when both Transmitter and Receiver

are connected through CAT cable. When it blinks regularly it states

the Receiver is NOT sending signal but the Transmitter and Receiver

are linked and if it blinks irregularly it states an error has occurred.

6.3. IR Cable Pin Assignment

Power

IR Blaster Signal

IR Signal

Power

Grounding

IR Extender

IR Blaster

6.4. D-Sub 9 Pin Denitions

Pin Dene TX / RX

1 N/C

2TxD / RxD

3RxD / TxD

4 N/C

5 GND

6 N/C

7 N/C

8 N/C

9 N/C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CYP Extender Handbücher

CYP

CYP CDVI-1109TXC Bedienungsanleitung

CYP

CYP CH-1109TX Bedienungsanleitung

CYP

CYP PU-1107-KIT Bedienungsanleitung

CYP

CYP CETH-4USB Bedienungsanleitung

CYP

CYP PUV-1530TXRX Bedienungsanleitung

CYP

CYP CH-506TX Bedienungsanleitung

CYP

CYP CH-506TXPLBD Bedienungsanleitung

CYP

CYP PU-1107-KIT Bedienungsanleitung

CYP

CYP CH-506TX Bedienungsanleitung

CYP

CYP CH-1529TXPL Bedienungsanleitung

CYP

CYP PU-1106-KIT Bedienungsanleitung

CYP

CYP CH-710TX Bedienungsanleitung

CYP

CYP CH-1107EX Bedienungsanleitung

CYP

CYP PUV-1510RX Bedienungsanleitung

CYP

CYP CH-1109TXC Bedienungsanleitung

CYP

CYP CH-1529TX Bedienungsanleitung

CYP

CYP CH-1527TXPL Bedienungsanleitung

CYP

CYP PU-DVI513L-KIT Bedienungsanleitung

CYP

CYP DCT-32TX Bedienungsanleitung

CYP

CYP CH-1106TX & RX Bedienungsanleitung

CYP

CYP IP-7000RX Bedienungsanleitung

CYP

CYP PU-USBX Bedienungsanleitung

CYP

CYP CH-514TXL Bedienungsanleitung

CYP

CYP AU-1HARC Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung