CYP AVIP-P5104R-B1C Bedienungsanleitung
Operation Manual
Operation Manual
UHD+HDMI AV over IP Receiver
AVIP-P5104R-B1C
DISCLAIMERS
The information in this manual has been carefully checked and is believed
to be accurate. Cypress Technology assumes no responsibility for any
infringements of patents or other rights of third parties which may result from
its use.
Cypress Technology assumes no responsibility for any inaccuracies that
may be contained in this document. Cypress also makes no commitment to
update or to keep current the information contained in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express written
permission and consent from Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document are trademarks of
the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply. Please keep the
following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture
or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings
or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it
is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to
be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings
in the unit housing that provide ventilation and allow for sucient space
for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in use to
avoid wasting electricity.
VERSION HISTORY
REV. DATE SUMMARY OF CHANGE
RDV1 2022/01/06 Preliminary release
CONTENTS
1. Introduction...................................................... 1
3. Package Contents ........................................... 2
4. System Requirements..................................... 2
5. Features............................................................ 3
6. Operation Controls and Functions ................ 4
6.1 Front Panel.................................................. 4
6.2 Rear Panel................................................... 5
6.3 IR Cable Pinouts.......................................... 7
6.4 RS-232 Pinout and Defaults........................ 7
6.5 OSD Menu................................................... 8
6.6 Basic AV Extension.................................... 12
6.6.1 Point-to-Point (One Way) ................. 12
6.7 Advanced AV Extension............................. 13
6.7.1 IP Master Controller ......................... 13
6.7.2 Conguration Examples ................... 14
7. Connection Diagram ..................................... 16
8. Specications ................................................ 17
8.1 Technical Specications ............................ 17
8.2 Video Specications .................................. 18
8.3 Audio Specications .................................. 20
8.3.1 Digital Audio ..................................... 20
8.3.2 Analog Audio .................................... 20
8.4 Cable Specications.................................. 21
9. Acronyms ....................................................... 22
1
1. INTRODUCTION
This AV over IP Receiver is designed for high-quality, IP routable, AV
extension with minimum latency. By using a sophisticated ultra-light
compression scheme (lossless for most content) it’s a great solution for
extending 4K audio/video streams and data. Advanced HDMI content such
as HDR (High Dynamic Range), 10-bit color and multi-channel HD Bitstream
audio can be transmitted in pass-through mode.
The use of high quality 10 Gigabit Ethernet ports and Cat.6A or better cable
allows for point-to-point transmission of the video signal up to 100m. Multiple
control and data signals may also be transmitted along with the audio and
video, including IR, RS-232, USB 2.0, and Ethernet.
When combined with the optional IP Master Controller or control software,
the functionality of the receiver expands exponentially. Multiple transmitters
and receivers may be combined with one or more 10 Gigabit Ethernet
switches and the units can be used together to form a distributed video
matrix, a multiviewer system, or a video wall system adding to their exibility
in large event installations.
The integrated USB hub of each receiver can function as a simple point to
point KVM extension or freely routed between any two endpoints. This type
of USB KVM routing exibility enables a wide range of multi-user, control
room, or on-demand installation scenarios.
The built-in EDID and HDCP management functionality enables the unit to t
into every situation. Basic conguration of the unit can be achieved via front
panel buttons with an OSD (On-Screen Display). Advanced control requires
the optional IP Master Controller, or control software, and a LAN connection.
2
2. APPLICATIONS
• Video, Audio, LAN, IR, and USB 2.0 over Cat.6A extension
• Point-to-Point Secure Video Conferencing
• Hotel or convention center display
• Multi-monitor broadcast
• Distributed video matrix system
• Distributed video wall system
• Remote KVM system control
3. PACKAGE CONTENTS
• 1× UHD+ HDMI AV over IP Receiver
• 1× 12V/3A DC Power Adapter
• 1× Power Cord
• 1× Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI receiving equipment such as an HDTV, monitor, or audio amplier
• Analog audio receiving equipment such as headphones, an audio
amplier, or powered speakers
• The use of Premium High Speed HDMI cables, and industry standard
Cat.6A, or Cat.7 Ethernet cable is required.
• A 10 Gigabit Ethernet network switch with jumbo frame and IGMP
snooping support is required for distributed video systems (Optional,
required for multi-transmitter/receiver systems)
• IP Master Controller or PC control software to congure distributed matrix,
video wall, or multi-view systems (Optional)
3
5. FEATURES
• HDMI 2.0 and DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• 1 Cat.6A input
• 1 HDMI output
• 1 analog stereo input & 1 analog stereo output
• 2 USB 2.0 (Type-A) ports and 1 USB 2.0 (Mini-B) port
• IP routable with minimum latency (requires optional IP Master Controller or
control software)
• Ultra-light compression, lossless for most content
• Extension up to 100m in Point-to-Point mode (with Cat.6A cable)
• Supports independent breakaway A/V matrix switching with minimum
latency, video wall generation, and multi-view compositing (requires
optional IP Master Controller/control software)
• Supports pass-through of 10/12-bit HDR sources (Point-to-Point and
Bypass modes only)
• Supports pass-through of audio formats including LPCM (up to 8
channels), Bitstream and HD Bitstream from HDMI or DP sources
• Analog stereo audio extension, insertion and extraction (insertion and
extraction requires optional IP Master Controller/control software)
• Unit can be powered directly by PoE when connected to a 10 Gigabit
Ethernet (10GbE) switch that provides PoE (802.3at)
• Basic conguration via front panel buttons with an OSD
• Supports the use of an external control center (IP Master Controller) or
control software to provide expanded functionality (Contact your authorized
dealer for more information)
4
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
GbE VIDEO LINK USBLINK USB
USB 2.0 MENU + ENTER
INFO
-
POWER
1 2 3 4 5 6 7
1POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
2USB 2.0 (Type-A) Ports: Connect directly to standard USB devices such
as a mouse, keyboard or ash drive to extend their USB functionality to
the currently active/routed USB Device Mode transmitter.
3STATUS LED BLOCK:
GbE LED: This LED will illuminate and blink to indicate a live and
active connection on the local gigabit Ethernet port.
VIDEO LED: This LED indicates video streaming activity over the
Cat.6A port. It will illuminate green when a video signal is being
transmitted. When no video is active the LED will remain o, even if
the streaming connection is valid.
LINK LED: This LED will illuminate and blink to indicate data
transmission activity across the Cat.6A streaming connection.
USB LED: This LED will illuminate when the unit’s USB ports have
successfully paired with the USB ports on another unit. This LED will
remain o if the unit’s USB ports are not currently paired and in stand-
by mode.
4MENU Button: Press to enter the OSD menu, or to back out from menu
items.
5 − (MINUS) Button: Press to move down or adjust selections within OSD
menus.
6+ (PLUS) Button: Press to move up or adjust selections within OSD
menus.
7ENTER/INFO Button: When inside an OSD menu, press to conrm a
selection or to go deeper into a menu item. When not in a menu, press to
activate the Information OSD.
5
6.2 Rear Panel
USB/SERVICELANRS-232IN
IR
OUTINOUTCAT6A/7 INHDMI OUT
DC 12V
AUDIO
TX RX
12 3 4 5 6 78
1HDMI OUT Port: Connect to an HDMI TV, monitor, or amplier for digital
video and audio output.
2CAT6A/7 Port: Connect directly to a compatible transmitter for Point-
to-Point extension, or to a 10 Gigabit Ethernet switch for distributed
matrixing (requires IP Master Controller or control software), with a single
Cat.6A/7 cable for extension of all data signals.
Note: If the connected network switch supports the IEEE 802.3at-2009
PoE (Power over Ethernet) standard, this unit can optionally be powered
directly via this Ethernet port.
3AUDIO PORTS:
OUT Port: Connect to powered speakers or an amplier for stereo
analog audio output.
IN Port: Connect to the stereo analog output of a device such as a CD
player or PC.
Note: When units are connected directly in a Point-to-Point
conguration, audio is routed directly from the IN Ports to the opposite
end’s OUT Ports. Free routing can only be congured by use of the
optional IP Master Controller or control software.
4IR PORTS:
OUT Port: Connect to an IR Blaster to broadcast IR signals from
a connected receiver to devices within direct line-of sight of the IR
Blaster.
IN Port: Connect to an IR Extender to receive IR control signals and
extend them to devices connected to a connected transmitter. Ensure
that the remote being used is within direct line-of-sight of the IR
Extender.
Note: Currently, only 38KHz IR signal extension is supported.
5RS-232 3-pin Terminal Block: Connect directly to a PC, laptop or serial
controllable device with a 3-pin adapter cable to extend the RS-232
signal between units.
Inhaltsverzeichnis
Andere CYP Empfänger Handbücher
CYP
CYP AU-A300-HBT Bedienungsanleitung
CYP
CYP AVX-101C-KIT Bedienungsanleitung
CYP
CYP CDVI-301TX & RX Bedienungsanleitung
CYP
CYP CH-A320RX Bedienungsanleitung
CYP
CYP AVX-101F-KIT Bedienungsanleitung
CYP
CYP PU-606PLBD-TX Bedienungsanleitung
CYP
CYP DCT-30RX Bedienungsanleitung
CYP
CYP PU-515PLRX-2HCD Bedienungsanleitung
CYP
CYP HDMI Over CAT5 Bedienungsanleitung
CYP
CYP CH-106TXN Bedienungsanleitung
CYP
CYP CH-1106TX & RX Bedienungsanleitung
CYP
CYP CWHDI-TX1 Bedienungsanleitung
CYP
CYP PU-507RX-SCD Bedienungsanleitung
CYP
CYP PU-305BD-RX Bedienungsanleitung
CYP
CYP PU-1109KIT Bedienungsanleitung
CYP
CYP CA-USBAT Bedienungsanleitung
CYP
CYP CH-1604TXD Bedienungsanleitung
CYP
CYP PRO-HDMIFO-4K Bedienungsanleitung
CYP
CYP PU-607BD-RX Bedienungsanleitung
CYP
CYP Dante AU-DTO4-RX Bedienungsanleitung
