CYP EL-5500 Bedienungsanleitung
EL-5500
Advanced HDMI/VGA Presentation Switch
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 29/09/13 First Release
v1.01 02/07/13 Updates
v1.02 03/07/13 Added 'Free run' colours
CONTENTS
1. Introduction ...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features ..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel ................................................... 8
6.2 Rear Panel ..................................................... 9
6.3 Remote Control ........................................10
6.4 RS-232 Protocols ......................................11
6.5 RS-232 and Telnet Commands ............12
6.6 OSD Menu ..................................................15
6.7 Telnet Control ............................................20
6.8 Web GUI Control ......................................22
6.9 Input Resolution Support .....................23
6.10 Output Resolution Support ...............24
7. Connection Diagram .......................... 25
8. Specications ...................................... 26
9. Acronyms ............................................. 27
6
1. INTRODUCTION
The EL-5500 is an advanced rack mountable HDMI, VGA, Composite, and
Component presentation switcher. This device can scale and switch input
sources to it's two HDMI outputs, with their associated audio signals to
the native resolutions supported by the connected display. Control is via
the IR remote, RS-232, IP, or via manual selection buttons. Both digital and
analogue stereo audio is supported via a built-in DAC (Digital to Analogue
Converter) and ADC (Analogue to Digital Converter). The EL-5500 is the
perfect solution for any educational or commercial environment requiring
integration of multiple sources and signal formats to two HDMI displays.
2. APPLICATIONS
Analogue and digital source integration
Upscaling standard denition video for high-denition displays
Conference centres
Lecture halls
Schools and universities
3. PACKAGE CONTENTS
Multi Input Scaler
Remote Control (CR-122)
D-Sub to RCA adaptor cable
Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as Blu-ray/DVD players or PC/NB, output
display and amplier or speakers.
7
5. FEATURES
v1.3 HDMI, HDCP 1.1 and DVI 1.0 compliant
Digital to Analogue & Analogue to Digital Audio conversion (DAC/ADC)
Supported Resolutions: HDTV: 480i to 1080p PC: VGA to WUXGA
Aspect Ratio Adjustment
Motion Adaptive De-interlace (3D)
Video Noise Reduction
Underscan / Overscan Selection
Picture Adjustment Settings
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
UNEM3 IMDH2 IMDH1 IMDH3 CP2 CP1 CPPMOCVCREWOP
XGA
ENTER
-
+
720P
3 4 5 621
1 POWER Button and LED: Press this button to switch the device on or
to set it to standby mode. Once the device is connected to an active
power supply the LED will illuminate and the device will switch on
automatically.
2 IR Receiver Window: Receives only the IR signal from the remote
control included in the package.
3 INPUT Buttons and LEDs: Press these buttons to switch directly to
the required source. An LED will illuminate to indicate the selected
input source.
4 MENU: Press this button to enter the On-screen Display (OSD) menu.
5 Plus/Minus (−/+) Buttons: Press these buttons to navigate down and
up in the OSD menu.
6 ENTER: Press this button to conrm the selection in the OSD menu.
Note: Press this button simultaneously with the '+' (plus) button to
instantly switch the output to XGA resolution or with the '−' (minus)
button to instantly switch the output to 720p resolution.
9
6.2 Rear Panel
POWER
DC 5V
CONTROL
HDMI 2HDMI 1 PC/HD
RS232 COAX AUDIO
SERVICE
OUTPUT
3 CP2 CP1 CP3 IMDH2 IMDH1 IMDH Cr/Pr Cb/Pb
R L
YR L CV
AUDIO
INPUT
IR IN
5 84
1 2 3 6 7
1 IR IN: Connect the supplied IR extender to receive the IR signal from
the included IR remote. Ensure that the remote is within the direct
line-of-sight of the IR extender.
2 SERVICE: Reserved for manufacturer use only.
3 RS-232: Connect to a PC/Laptop or RS-232 control system to use RS-
232 commands to control the device (See Section 6.5 for details on
RS-232 commands).
4 OUTPUT
1) HDMI 1/2: Connect to an HDMI display or AV Receiver for video
and/or audio output.
2) PC/HD: Connect to a monitor/display for video output. For HD
(Component) output, use the supplied D-Sub 9pin to 3 RCA adaptor
cable for HD resolutions from 480p~1080p.
3) COAX: Connect to an amplier or active speakers for audio output
in digital format.
Note: When the input audio source signal is in bitstream format and
the AUDIO SOURCE setting is set to AUTO in the OSD menu, the coaxial
output will bypass the input audio signal including compatible surround
sound formats.
4) AUDIO: Connect to an amplier or active speakers for audio output
in stereo format.
5 INPUT
1) HDMI 1/2/3: Connect to HDMI sources such as Blu-ray/DVD player
for both video and audio signal conversion.
2) PC 1/2/3: Connect to a PC/Laptop source for video signal input
with a D-Sub 15pin cable.
3) 3.5mm Mini-jacks: Connect to source's L/R output with 3.5mm
mini-jack for audio signal conversion.
10
Note: For HDMI signals you can select in the OSD Menu whether you require
audio from the HDMI (AUTO) or from the analogue audio inputs (EXT)
4) YCbCr/YPbPr + L/R: Connect to source equipment such as a DVD
player for both video and audio signal conversion.
5) CV + L/R: Connect to a composite video source such as a video/
DVD player for both video and audio signal conversion.
6 CONTROL: This port is the link for Telnet or Web GUI controls, connect
to an active Ethernet link with an RJ45 terminated cable
7 POWER: Switch this power toggle to turn on and activate the device
or turn o to shut it down.
8 DC 5V: Connect the power adaptor included in the package to the
device and plug it into an AC wall outlet for power supply.
6.3 Remote Control
1 POWER: Press this button to switch the device on or to set it to
standby mode.
2 HDMI1/2/3, PC1/2/3, CV and COMP:
Direct source selection keys. Press one
of these keys to switch to the required
source.
3 MENU: Press this button to enter the
OSD menu.
4 EXIT: Press this button to exit the menu
or the current selection in the OSD
menu.
5 OK & ▲▼◄►: Press OK to conrm the
selection or press the arrow buttons to
navigate the OSD menu. When the OSD
menu is not active, use the LEFT/RIGHT
(◄►) to control the volume level.
6 AUTO ADJUST: Press this button when
the image being outputted does not
correctly t the display's screen. The
device will auto adjust the image to ll
the screen.
7 RESET: Press this button to reset the device back to the default
settings.
CR-122
POWER
EXIT MENU
OK
RESET AUTO
ADJUST
PC1 PC2 PC3
CV COMP
HDMI2HDMI1 HDMI3
1
3
6
5
4
7
2
Andere Handbücher für EL-5500
1
Inhaltsverzeichnis
Andere CYP Schalten Handbücher
CYP
CYP CVSD-41ARN Installationshandbuch
CYP
CYP CLUX-31GAME Bedienungsanleitung
CYP
CYP CMLUX-4H4CAT Bedienungsanleitung
CYP
CYP EL-41S-4K22 Bedienungsanleitung
CYP
CYP CDPS-U42HPIP Installationshandbuch
CYP
CYP CED-1M Bedienungsanleitung
CYP
CYP EL-41WAD Bedienungsanleitung
CYP
CYP CSC-5300 Bedienungsanleitung
CYP
CYP DCT-31 Bedienungsanleitung
CYP
CYP CSSW-91WF Bedienungsanleitung
CYP
CYP AU-D41 Bedienungsanleitung
CYP
CYP CPRO-U4H1HFS Bedienungsanleitung
CYP
CYP EL-21SY Bedienungsanleitung
CYP
CYP CDPS-41SQ Bedienungsanleitung
CYP
CYP DT-21 Bedienungsanleitung
CYP
CYP CPLUS-31PS Bedienungsanleitung
CYP
CYP CFSW-51MHL Bedienungsanleitung
CYP
CYP EL-41PIP Bedienungsanleitung
CYP
CYP EL-5600 Bedienungsanleitung
CYP
CYP EL-41X Bedienungsanleitung
