CYP CMLUX-4H4CAT Bedienungsanleitung
CMLUX-4H4CAT
4 by 4 HDMI V1.3
over CAT 5 Matrix
Operation Manual
CMLUX-4H4CAT
Revision History
Version No. Date Summary of Change
V1 20090610 Preliminary Release
Precautions
Failure to follow the precautions described below may cause damage to 4
by 4 HDMI V1.3 over CAT 5 Matrix and void the warranty.
DO NOT open the case. Doing so will void the warranty. If you
nd problem with it, please return back to your retailer or seller
who will assist you or provide you with solution.
DO NOT use third-Party AC adapter or power cord. Doing so may
damage 4 by 4 HDMI V1.3 over CAT 5 Matrix.
DO NOT bump, jar or drop contents of the products as it may
damage it and result in warranty void.
DO NOT set any liquids or beverages on the drive as they may
damage 4 by 4 HDMI V1.3 over CAT 5 Matrix.
Table of Contents
1
1
1
1
2
3
3
4
5
5
5
6
7
8
1. Introduction.....……………………..…………………................................
2. Applications...........................…..…………………………………….....…
3. Package Contents..............................……………………………….…….
4. System Requirements.............................……………………………..……
5. Features................................…..…………………………………...………..
6. Installation..............................…………………………………...…………..
6.1. Front Panel......................…………………………………...…………..
6.2. Rear Panel.......................…………………………………...…………..
7. Remote Control.......................…..……………………………...…………..
8. RS-232 Protocal.......................…………..……………………...…………..
8.1 Pin Denition....................…………..……………………...…………..
8.2 Commands.....................…………………….……………...…………..
9. Connection and Installation..................................................................
10. Specications..........................................................................................
1. Introduction
This high performance HDMI Matrix over CAT 5 with remote control is
compatible with HDMI v1.3 specications. A cutting-edge technology which
denes the supports to transfer Deep Color (10 bits/color) video and new
lossless compressed (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master
Audio) digital audio. It offers you maximum convenience in HDMI signal
distribution when you have multiple HDMI sources and displays to connect
together. Each of the four HDMI sources can be directed to any one of
the four displays. When HDMI signal progresses through the system, it is re-
timed, and level-compensated. Further, since signal is transferred over CAT
5 the distance can be extended at the lowest cost yet with same quality.
Moreover, with built-in IR system users can control the sources with existing
remote controls from the display side and EDID switch allowing users to
choose display resolution. Last but not least, the RS-232 function easy system
control over PC which make this device in a perfect form.
2. Applications
Multi-source with multi-display control.
Home entertainment integration.
Multi-task project presentation.
Showroom Display.
Advertising display control.
System installation control.
3. Package Contents
4 by 4 HDMI V1.3 Matrix.
Remote Control (with Battery)
IR Receiver
IR Blaster
Power Cord
5V DC power supply adaptor.
Operation Manual.
4. System Requirements
Input source equipment(s) and output display device(s) with HDMI cables
and CAT 5 to HDMI receiver.
1
5. Features
HDMI 1.3, HDCP 1.1 and DVI 1.0 compliant.
Supports digital video formats in Deep Color Mode at up to 30 bits (10bits/
color) and new lossless compressed (Dolby TrueHD, Dolby Digital Plus
and DTS-HD Master Audio) digital audio.
The HDMI input is compensated, clock / phase adjusted, and jitter
eliminated so the output is a brand new standard HDMI signal.
Supports input source LED indicators on each output select.
Compatible with all HDMI sources and displays.
Supports a wide range of PC and HDTV resolutions from VGA to UXGA
and 480i to 1080p.
Supports RS-232 control.
Supports IR remote control with IR extender and blaster.
Dolby Digital, DTS digital audio transmission (32-192 kHz Fs sample rate).
Supports LPCM7.1 channels output from each independent HDMI ports.
HDMI cable distance test with 1080p/8 bits resolution, the Input/Output
can run up to 20/15 meters. With 1080p/10 bits the Input/Output can run
up to 15/15 meters.
Switchable EDID function for choosing the native resolution to display.
Dene HDCP, HDMI and DVI source with LED light.
Re-timed and level-compensated with HDMI signal progress.
High performance HDMI 1.3 Matrix allowing full entertainment enjoyment
on movies, music, games and TV at once.
2
6. Installation
6.1 Front Panel
①. Remote control sensor.
②. Power switch & LED Indicator: The LED will illuminate when the power is
turned on.
③. Input Select/Indicators (A/B/C/D): Press the “HDMI out A”button
repeatedly to switch to your desired source and the LED will illuminate
to indicate which input source is being selected and routed to HDMI A
display.
④. HDCP indicators: When the input source is with the HDCP protection the
HDCP LED will illuminate.
⑤. HDMI/DVI indicators: LED will illuminate when input source is HDMI
content, when the input source is DVI the LED will not illuminate.
①②
③
④⑤
3
①. EDID Control Switcher: Default factory setting is TV, leave as if the display
is properly. Switch to STD to use built-in EDID.
[Note]:
1. When EDID switch to TV, the unit will detect the rst HDMI output
source’s EDID and record in the unit. If the rst detected output
source is DVI it will pass to next source until the rst HDMI source been
detected. The detection priority is HDMI v1.3 > HDMI v1.2 > DVI.
2. When EDID switch to STD the unit will use built-in EDID which supports:
Video →1080p 12-bit (max) but not supports xvYCC
Audio →PCM 2CH
3. The EDID selection will only activated when the unit is re-plug and
power on.
②. RS-232: Connect to the COM port of your PC for the distant control over
RD-232 channel. Detail specication in section 8.
③. Video/DDC CAT 5 outputs: Connect each of these output ports with CAT
5 cables to CAT 5 to HDMI receiver and then to display with HDMI cable.
④. HDMI inputs: Connect input ports to the HDMI or DVI output of your
source equipment such as DVD player or set-top-box.
⑤. Power: Plug the 5VDC power supply into the unit and connect the
adaptor to AC wall outlet.
⑥. IR IN: Place the IR receiver cable in front of the display and then use the
existing remote controls to control both sources and display.
⑦. IR OUT: Place the IR blaster cable in front of the sources and then use the
existing sources remote controls to control the source equipments.
6.2 Rear Panel
① ② ⑥⑤④③ ⑦
4
7. Remote Control
1. Power: Press the button to turn on/off the unit.
2. Input Select for HDMI OUT A: Press 1, 2, 3 or 4 to
select the desired input source for HDMI OUT A.
3. Input Select for HDMI OUT B: Press 1, 2, 3 or 4 to
select the desired input source for HDMI OUT B.
4. Input Select for HDMI OUT C: Press 1, 2, 3 or 4 to
select the desired input source for HDMI OUT C.
5. Input Select for HDMI OUT D: Press 1, 2, 3 or 4
to select the desired input source for HDMI OUT D.
* RS-232 transmission format:
Baud Rate: 9600bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Control: None
8. RS-232 Protocal
8.1 Pin Denition
CMLUX-4H4CAT Remote Control Console
PIN Denition
→
←
PIN Denition
1 NC 1 NC
2 TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
5
5
8.2 Commands
COMMAND ACTION
POWER 00
;
Power Off (standby)
POWER 01
;
Power On
PORT 11
;
Output A select Input1
PORT 12
;
Output A select Input2
PORT 13
;
Output A select Input3
PORT 14
;
Output A select Input4
PORT 21
;
Output B select Input1
PORT 22
;
Output B select Input2
PORT 23
;
Output B select Input3
PORT 24
;
Output B select Input4
PORT 31
;
Output C select Input1
PORT 32
;
Output C select Input2
PORT 33
;
Output C select Input3
PORT 34
;
Output C select Input4
PORT 41
;
Output D select Input1
PORT 42
;
Output D select Input2
PORT 43
;
Output D select Input3
PORT 44
;
Output D select Input4
6
9. Connection and Installation
HD TV HD TV
HD TV HD TV
7
Inhaltsverzeichnis
Andere CYP Schalten Handbücher
CYP
CYP CPLUS-V3H1H Bedienungsanleitung
CYP
CYP EL-5500 Bedienungsanleitung
CYP
CYP EL-42S Bedienungsanleitung
CYP
CYP MA-U42 Bedienungsanleitung
CYP
CYP EL-21SY Bedienungsanleitung
CYP
CYP EL-41PIP Bedienungsanleitung
CYP
CYP EL-5400 Bedienungsanleitung
CYP
CYP CDPS-U4H4HSA Bedienungsanleitung
CYP
CYP PU-444HBTE Bedienungsanleitung
CYP
CYP CPLUS-V4H1H Bedienungsanleitung
CYP
CYP CDPS-UH4H1HFS Bedienungsanleitung
CYP
CYP CLUX-42S Bedienungsanleitung
CYP
CYP EL-5500-HBT Bedienungsanleitung
CYP
CYP EL-5400D Bedienungsanleitung
CYP
CYP EL-42S Bedienungsanleitung
CYP
CYP EL-M31TT-4K22 Bedienungsanleitung
CYP
CYP PU-8H8HBT Bedienungsanleitung
CYP
CYP EL-41S-4K22 Bedienungsanleitung
CYP
CYP CDPS-41SQ Bedienungsanleitung
CYP
CYP CLUX-42SA Bedienungsanleitung
