Danfoss ECtemp 130 Bedienungsanleitung

ECtemp

130

Electronic Thermostat

Installation Guide

electricheating.danfoss.com

ECtemp 130

Installation Guide2

ECtemp 130

3Installation Guide

1 Introduction

ECtemp 130 is an electronic thermostat to be installed di-

rectly on the wall. It is provided with a oor sensor to measure

and control the desired oor temperature.

The thermostat has a button for adjusting the temperature

setting with a scale from ( ) 1 to 5 (each step corresponds to

approximately 9°C). Furthermore, the thermostat has an LED

indicator showing standby periods (green light) and heating

periods (red light).

More information on this product can also be found at:

ectemp.danfoss.com

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Technical Specications . . . . . . . . . . . . 4

1.2 Safety Instructions . . . . . . . . . . . . . . . 5

2 Mounting Instructions . . . . . . . . . . . . . . . . . 6

3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1 Temperature Settings. . . . . . . . . . . . . 10

4 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 14

5 Disposal Instruction . . . . . . . . . . . . . . . . . 16

ECtemp 130

Installation Guide4

1.1 Technical Specications

Operation voltage 220-240V~, 50Hz

Power consumption Max 5W

Relay:

Resistive load

Inductive load

Max 16A / 3680W @ 230V

cos φ= 0.3 max 1A

Sensing units NTC 15 kOhm at 25°C

Sensing values:

0 °C

25 °C

50 °C

42 kOhm

15 kOhm

6 kOhm

Hysteresis ± 0,2 °C

Ambient temperature 0 to +30°C

Frost protection temperature 5 °C -

Temperature range ( ) 5–45 °C

Cable specication max 1x4 mm² or 2x2,5 mm²

Ball pressure temperature 75 °C

Pollution degree Degree 2 (domestic use)

Type 1C

Storage temperature -20 to +65°C

IP class 30

Protection class Class II -

ECtemp 130

5Installation Guide

Dimensions 82 x 82 x 36 mm

Weight 90 g

The product complies with the EN/IEC Standard «Automatic

electrical controls for household and similar use»:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1.2 Safety Instructions

Make sure the mains supply to the thermostat is turned o

before installation.

IMPORTANT: When the thermostat is used to control a

oor heating element in connection with a wooden oor or

similar material, always use a oor sensor and never set the

maximum oor temperature to more than 35°C.

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualied installer according to local

regulations.

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• The sensor is to be considered as live voltage. Have

this in mind if the sensor must be extended.

ECtemp 130

Installation Guide6

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water,

dust, and excessive heat.

2 Mounting Instructions

Please observe the following placement guidelines:

Place the thermostat at a suitable height on

the wall (typically 80-170cm.).

In wet rooms, place the thermostat

according to local regulation on IP classes.

Do not place the thermostat on the inner

side of an exterior wall.

ECtemp 130

7Installation Guide

• Place the oor sensor in a conduit in an

appropriate place where it is not exposed

to sunlight or draft from door openings.

• Equally distant and >2cm from two heat-

ing cables.

• The conduit should be ush with the

oor surface - countersink the conduit if

necessary.

• Route the conduit to the connection box.

• The bending radius of the conduit must

be min 50mm.

ECtemp 130

Installation Guide8

Follow the steps below to mount the thermostat:

1. Open the thermostat:

• Lift o the button using a small screwdriver.

• Loosen the screw which holds the front.

• Push down the release tab at the top of the

thermostat using a at object while slowly pulling o

the front cover.

ECtemp 130

9Installation Guide

2. Fasten the thermostat directly to the wall by driving

the screws through the holes in each side of the

thermostat.

1= Screw holes for fastening the thermostat.

3. Connect the thermostat according to the

connectiondiagram.

IP30

0T30

D130

NTC

1234

Sensor

Max.Load

16 (1) A

Mains

220-240V~

LOAD

The screen of the heating cable must be connected

to the earth conductor of the power supply cable by

using a separate connector.

Note: Always install the oor sensor in a conduit in

the oor.

ECtemp 130

Installation Guide10

4. Install the front cover and button in the reverse order

of disassembly.

5. Turn on the power supply.

3 Settings

3.1 Temperature Settings

How to change the minimum and maximum oor

temperatures

1. Lift o the adjustment

button using a thin

screwdriver. (1)

2. Move the pins to the

desired positions. (2 and 3)

3. Put the adjustment button

back in place.

Please be aware of the following:

• The oor temperature is measured where the sensor

is placed.

• The temperature of the bottom of a wooden oor can

be up to 10 degrees higher than the top.

• Floor manufactures often specify the max

temperature on the top surface of the oor (usually

27-28˚C).

Inhaltsverzeichnis

Andere Danfoss Thermostat Handbücher

Danfoss

Danfoss REP24 Bedienungsanleitung

Danfoss

Danfoss REPI Series Bedienungsanleitung

Danfoss

Danfoss CF-RS Bedienungsanleitung

Danfoss

Danfoss HCS6101-3 Gebrauchsanweisung

Danfoss

Danfoss GreenCon RC-C2 Bedienungsanleitung

Danfoss

Danfoss TP9000 Si Bedienungsanleitung

Danfoss

Danfoss TP7001 series Bedienungsanleitung

Danfoss

Danfoss DEVIreg 610 Bedienungsanleitung

Danfoss

Danfoss TP5001 series Gebrauchsanweisung

Danfoss

Danfoss ECtemp 531 Bedienungsanleitung

Danfoss

Danfoss ECtemp 330 Bedienungsanleitung

Danfoss

Danfoss REPI Series Bedienungsanleitung

Danfoss

Danfoss LX205T Bedienungsanleitung

Danfoss

Danfoss TPOne-M Bedienungsanleitung

Danfoss

Danfoss CF-RP 088U0211 Bedienungsanleitung

Danfoss

Danfoss TP5001 series Bedienungsanleitung

Danfoss

Danfoss TP5000 si range Leitfaden

Danfoss

Danfoss EFIT 540 Bedienungsanleitung

Danfoss

Danfoss KPU 61 Bedienungsanleitung

Danfoss

Danfoss Link FT Bedienungsanleitung

Danfoss

Danfoss Icon Master Bedienungsanleitung

Danfoss

Danfoss living connect Bedienungsanleitung

Danfoss

Danfoss TS715 Si Bedienungsanleitung

Danfoss

Danfoss RT1 Montageanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung