Danfoss ECtemp 610 Bedienungsanleitung

ECtemp 610

Electronic Thermostat IP44

Installation Guide

electricheating.danfoss.com

ECtemp 610

3Installation Guide

1 Introduction

ECtemp 610 is an IP44 electronic thermostat to be installed

directly on the wall. It is provided with a 2-pole switch and a

wire sensor to control the desired temperature.

The thermostat has a button for adjusting the temperature

setting with a scale from -10 °C to +50 °C, and an LED indi-

cator that shows standby periods (green light) and heating

periods (red light).

More information on this product can also be found at:

ectemp.danfoss.com

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . 3

1.1 Technical Speciﬁcations . . . . . . . . . . . 4

1.2 Safety Instructions . . . . . . . . . . . . . . . 5

2 Mounting Instructions . . . . . . . . . . . . . . . 6

3 Warranty. . . . . . . . . . . . . . . . . . . . . . . 12

4 Disposal Instruction . . . . . . . . . . . . . . . 14

ECtemp 610

Installation Guide4

1.1 Technical Speciﬁcations

Operation voltage 220-240 V~, 50 Hz

Standby power consumption Max. 0,93 W

Relay:

Resistive load

Inductive load

Max 10 A / 2300 W @ 230V

cos φ= 0,3 max 1A

Sensing units NTC 15 kOhm at 25 °C

Sensing values:

0 °C

25 °C

50 °C

42 kOhm

15 kOhm

6 kOhm

Hysteresis ± 0,2 °C

Ambient temperature 10 °C to +50 °C

Temperature range -10 °C to +50 °C

Cable speciﬁcation max 1 x 4 mm² or 2 x 2,5 mm²

Ball pressure temperature 75 °C

Pollution degree 2 (domestic use)

Type 1C

Storage temperature 20 °C to +65 °C

IP class 44

Protection class Class II -

ECtemp 610

5Installation Guide

Dimensions 100 x 69,5 x 45 mm

Weight 165 g

The product complies with the EN/IEC Standard“Automatic

electrical controls for household and similar use”:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1.2 Safety Instructions

Make sure the mains supply to the thermostat is turned oﬀ

before installation.

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualiﬁed installer according to local

regulations.

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• The sensor is to be considered as live voltage. Have

this in mind if the sensor must be extended.

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water,

dust, and excessive heat.

ECtemp 610

Installation Guide6

2 Mounting Instructions

Please observe the following placement guidelines:

• The thermostat can be placed both indoors and

outdoors.

• Place the thermostat on a wall, pole, steel/wooden

plate or pipe.

In wet rooms, place the thermostat ac-

cording to local regulation on IP classes.

ECtemp 610

7Installation Guide

Follow the steps below to mount the thermostat:

1. Open the thermostat:

• Set adjustment button to minimum temperature.

• Loosen the 2 screws and open the front cover.

ECtemp 610

Installation Guide8

2. Fasten the thermostat:

• Drive the screws through the holes in the bottom

corners of the thermostat.

• Seal the holes with the enclosed screw stopper to

maintain the density.

ECtemp 610

9Installation Guide

3. Connect the thermostat according to the connection

diagram.

• Heating: (L-main, N-main, L-load, NO (normally

open) - load).

• Cooling: (L-main, N-main, L-load, NC (normally

closed) - load).

The screen of the heating cable must be connected

to the earth conductor of the power supply cable by

using a separate connector.

4. Reinstall the front cover.

5. Ensure that the adjustment button can be adjusted

within full temperature range, i.e. from -10 °C to +50 °C.

ECtemp 610

Installation Guide10

6. Install sensor using the supplied sensor cable -

NTC 15 kΩ @ 25 °C.

• Press out the blanket located at the bottom of the

thermostat and insert the seal nipple.

• Connect sensor to terminals 6+7.

The sensor cable can be extended up to 50 m with

1,5 mm² installation cable without aﬀecting the ac-

curacy of the thermostat.

Do not place the cable parallel to other installation

cables as undesirable signals may be induced.

The installation must be permanent.

If the sensor is to be built in, used for pipe applica-

tions, or exposed to pressure, always install it in a

conduit.

7. Turn on the power supply.

Inhaltsverzeichnis

Andere Danfoss Thermostat Handbücher

Danfoss

Danfoss RAS-C2 Combi Bedienungsanleitung

Danfoss

Danfoss RAVV-RAV8 Bedienungsanleitung

Danfoss

Danfoss FH-CWD Bedienungsanleitung

Danfoss

Danfoss TP5001 series Bedienungsanleitung

Danfoss

Danfoss TP75 Betriebsanleitung

Danfoss

Danfoss BasicPlus2 WT-T Bedienungsanleitung

Danfoss

Danfoss ECtemp 532 Bedienungsanleitung

Danfoss

Danfoss HC75-1 Betriebsanleitung

Danfoss

Danfoss TP7000 Series Bedienungsanleitung

Danfoss

Danfoss TS715 Si Montageanleitung

Danfoss

Danfoss DEVI DEVIreg Touch Bedienungsanleitung

Danfoss

Danfoss FP715Si Bedienungsanleitung

Danfoss

Danfoss CET2000B-RF Bedienungsanleitung

Danfoss

Danfoss HCS6101-3 Gebrauchsanweisung

Danfoss

Danfoss LX205T Bedienungsanleitung

Danfoss

Danfoss RTD 3120 Bedienungsanleitung

Danfoss

Danfoss RET2001RF Bedienungsanleitung

Danfoss

Danfoss FH-RT Handbuch

Danfoss

Danfoss TP4 Betriebsanleitung

Danfoss

Danfoss WT-DR Bedienungsanleitung

Danfoss

Danfoss LinkFT Bedienungsanleitung

Danfoss

Danfoss RET2000 B Bedienungsanleitung

Danfoss

Danfoss Eco Bedienungsanleitung

Danfoss

Danfoss Icon Master Controller 24 V Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung