DAVIS ISS Leitfaden

Product#6320W

NTEGRATED

ENSOR

UITE

NSTALLATION

ANUAL

The Integrated Sensor Suite (ISS) is an integrated, basically pre-assembled ﬁeld

station that collects data from attached sensors and then transmits it wirelessly,

or via cable, to a console. The ISS standard complement of sensors includes:

✦

Wind Speed

✦

Wind Direction

✦

Rainfall

✦

Outside Temperature

✦

Outside Humidity

The Wireless ISS is user-conﬁgurable to communicate on one of 8 different ID

codes. This allows multiple systems to coexist in the same geographical area.

Note:

The ISS operates on a low power frequency that does not require you to obtain an FCC license.

OOLS

AND

ATERIALS

EEDED

In addition to the components listed above, you may need some of the follow-

ing tools and materials.

✦

Phillips Screwdriver

✦

Pencil or Other Pointed Object

SSEMBLING

THE

ISS

To assemble the ISS, attach the anemometer arm to the ﬁeld station assembly.

Note:

Alternatively, you can choose mount the anemometer separately from the ISS base. This option

allows you to ensure clearance from possible airﬂow obstructions.

Page2 IntegratedSensorSuite

NSTALLING

THE

ISS

The instructions below will take you through the process required to install the

wireless and wired sensor suite.

Choosing a Location

As you position your sensor suite, try to avoid possible obstructions of rain

and wind—look out for trees and nearby buildings. If you have the wireless,

solar-powered ISS look for spots with good exposure to the sun throughout the

day.

For roof mounting, and for ease of installation in other locations, we recom-

mend using the optional Mounting Tripod (contact Davis for more informa-

tion).

Conﬁguring the ISS

✦

If you have a wired ISS, no conﬁguration is necessary.

✦

If you have a wireless ISS, the ISS’s transmitter must be setup so that it uses the

same ID code as your console/receiver.

For details on conﬁguring the wireless ISS, see page 3.

Applying Power to the ISS

Apply power to the transmitter using one of the options indicated below. For

all power options, Davis recommends using a backup battery to ensure power

during storms. Insert a CR-123 3-volt lithium cell as a backup.

✦

If you have a wireless system, plug the solar panel cord into the power jack on the

board.

The unit will operate off the day’s collected energy for up to 8 hours into

the night. The remainder of the night, the unit will tap into the backup

battery as a power source. Even so, the battery should last several years.

✦

If you have a wired system, simply plug the ISS cable into the console.

The console will provide any power needed by the ISS.

ConfiguringtheWirelessISS Page3

ONFIGURING

THE

IRELESS

ISS

Both the transmitter in the ISS and the receiver in the console have ID codes.

These ID codes enable a speciﬁc transmitter to “talk to” a speciﬁc receiver, even

if many transmitters are operating in the same area.

Setting the ID Code

The ISS may be set to use any of eight selectable ID codes (the default is ID

Code #1). The ISS and console/receiver will only communicate with each

other if they are both set to the same ID code. Use the default setting unless

you have another Davis wireless weather station operating nearby which you

want to work separately from the new system. The dip switch settings for the

eight possible codes are shown below.

To change to another ID, toggle dip switches 1, 2, and/or 3 on the ISS and then

set the console/receiver’s ID code to match. Remember that the ISS and con-

sole/receiver must use the same ID code in order to communicate.

Note:

Dip switch #4 is used for testing only, not for ID codes. See details below.

Test Mode

Dip switch #4 on the ISS allows you to conﬁgure the Test LED to ﬂash when-

ever a data packet is transmitted. This feature allows you to more easily set up

and test your transmitting system. When you are done setting up or testing,

however, make sure you

turn dip switch #4 to OFF so that the LED does not ﬂash

and waste signiﬁcant amounts of power unnecessarily

ID C

ODE

WITCH

(default)

off off off

#2 off off ON

#3 off ON off

#4 off ON ON

#5 ON off off

#6 ON off ON

#7 ON ON off

#8 ON ON ON

Product Numbers: 6150, 6150W, 6320

Davis Instruments Part Number: 7395

Integrated Sensor Suite Installation Manual

Rev. A Manual (8/5/99)

Controlled Online: Weather Manuals:DavisTalk:ISS

3465 Diablo Avenue, Hayward, CA 94545-2778

510-732-9229 • Fax: 510-732-9118

E-mail: [email protected] • www.davisnet.com

PECIFICATIONS

Transmit frequency: 916.5 MHz

ID codes: 8 user-selectable

License: Low power (less than 1 mW), no license required

Temperature range: -40 to 60 °C

Primary Power Input Options

Console Power: Cable running from Vanguard Pro console

Solar Power: Davis solar charger

Secondary (Backup) Power: CR-123 3- volt lithium battery or equal

FCC P

ART

15 C

LASS

B R

EGISTRATION

ARNING

This equipment has been tested and found to comply with the limits for a class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

✦

Reorient or relocate the receiving antenna.

✦

Increase the separation between the equipment and receiver.

✦

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

✦

Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved in writing by Davis Instru-

ments may void the user's authority to operate this equipment.

Inhaltsverzeichnis

Andere DAVIS Zubehör Handbücher

DAVIS

DAVIS Surge Protector Shelter (Small) Bedienungsanleitung

DAVIS

DAVIS 6440 Bedienungsanleitung

DAVIS

DAVIS Solar Power Kit Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS 7714 Radiation Shield Bedienungsanleitung

DAVIS

DAVIS Short-Range Modem Pair Bedienungsanleitung

DAVIS

DAVIS 6151 Bedienungsanleitung

DAVIS

DAVIS AirLink Bedienungsanleitung

DAVIS

DAVIS Vantage Vue ISS Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS AirLink 7210 Bedienungsanleitung

DAVIS

DAVIS Wireless Temperature/Humidity Station Bedienungsanleitung

DAVIS

DAVIS and Vantage Pro Bedienungsanleitung

DAVIS

DAVIS SONIC-ANEMO-DZP Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS Solar Radiation Sensor Bedienungsanleitung

DAVIS

DAVIS Vantage Pro ISS Retrofit Kit Bedienungsanleitung

DAVIS

DAVIS WeatherLink Live 6100 Bedienungsanleitung

DAVIS

DAVIS Vantage Pro2 Updater Bedienungsanleitung

DAVIS

DAVIS Wireless Temperature/Humidity Station Bedienungsanleitung

DAVIS

DAVIS Soil Moisture Sensor & Temperature Probe Bedienungsanleitung

DAVIS

DAVIS 7817 Bedienungsanleitung

DAVIS

DAVIS 6322C Bedienungsanleitung

DAVIS

DAVIS Solar Power Kit Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung