DFI QB701-B Series Bedienungsanleitung

QB701-B Series

Qseven Board

User’s Manual

A19720234

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use

of this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to

its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for identification pur-

pose only and are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

Introduction

Table of Contents

Trademarks........................................................................................2

FCC and DOC Statement on Class B..............................................3

About this Manual .............................................................................6

Warranty ..........................................................................................6

Static Electricity Precautions.............................................................7

Safety Measures.................................................................................7

About the Package ............................................................................8

Chapter 1 - Introduction ..................................................................9

Specifications..................................................................................9

Features ...................................................................................... 11

Chapter 2 - Hardware Installation.................................................. 12

Board Layout................................................................................ 12

Mechanical Diagram........................................................................................... 13

System Memory ........................................................................... 14

Cooling Option...................................................................................................15

MXM Connector ................................................................................................17

Installing QB701-B Series onto a Carrier Board .............................. 20

Chapter 3 - BIOS Setup.................................................................. 22

Overview .................................................................................... 22

AMI BIOS Setup Utility ................................................................. 24

Main....................................................................................... 24

Advanced................................................................................ 25

Chipset ................................................................................... 35

Boot....................................................................................... 39

Security.................................................................................. 40

Save & Exit............................................................................. 41

Updating the BIOS........................................................................ 42

Chapter 4 - Supported Software ................................................... 43

Introduction

Appendix A - NLITE and AHCI Installation Guide ......................... 58

nLite ....................................................................................................................... 58

AHCI...................................................................................................................... 66

Appendix B - System Error Message .............................................. 70

Appendix C - Troubleshooting........................................................ 71

Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual

in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board

Utility CD) will appear. Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Introduction

About the Package

The package contains the following items. If any of these items are missing or

damaged, please contact your dealer or sales representative for assistance.

One QB701-B Series board

One heat sink

One drivers/utilities disk

One QR (Quick Reference)

Optional Items

Q7-100 carrier board kit

Cable kit for carrier board

Two standoff bolts

Two sets of nut and bolt

One bracket

The board and accessories in the package may not come similar to the informa-

tion listed above. This may differ in accordance with the sales region or models

in which it was sold. For more information about the standard package in your

region, please contact your dealer or sales representative.

Introduction

Chipset

Expansion

Interfaces

Graphics

Audio

LAN

SDIO/MMC

Serial ATA

BIOS

Energy Efficient

Design

Power

TPM (option)

Watchdog Timer

Chapter 1 - Introduction

• Intel® EG20T PCH (Platform Controller Hub)

• Supports USB interface:

- 7 Host and 1 Host/Client (selectable)

• Supports LPC Interface

• Supports SMB and I2C interfaces

• Supports 3 PCIe x1 interfaces

• Supports CAN-bus (Controller-Area Network) interface

• Intel®GMA 600

• Supports up to 400MHz graphics frequency

• Ultra low power integrated 3D graphics

• High deﬁnition hardware video decoder and encoder engine

• Supports LVDS and SDVO interfaces

- LVDS: Supports pixel clock depths of 18/24-bit, single

channel, max. pixel clock of 80MHz, equates to

1280x768 @ 60Hz

- SDVO: Up to 160MHz pixel clock, equates to 1280x1024

@ 85Hz

• Supports High Deﬁnition Audio interface

• Integrated Intel®PCH GbE MAC

• One Micrel KSZ9021RNI Ethernet PHY

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) com-

pliant

• Supports 1 SDIO/MMC

• Supports SDA Standard Ver 1.0, SD memory card speci-

fication Ver 2.0, SDIO card specification Ver 1.0, MMC Sys-

tem specification Ver 4.1

• Conforms to Secure Digital Host Controller (SDHC) speed

class 6

• Supports two Serial ATA interfaces

- One port shared with SSD

• SATA speed up to 3Gb/s (SATA 2.0)

• 16Mbit SPI Flash BIOS (UEFI BIOS)

• Supports ACPI 2.0/1.0 specification

• Enhanced Intel®SpeedStep Technology

• Input: VCC_RTC, 5V standby, 5V

• Provides a Trusted PC for secure transactions

• Provides software license protection, enforcement and

password protection

• Software programmable from 1 to 255 seconds

Specifications

Introduction

Humidity

PCB • 10% to 90%

• Dimensions

- Qseven form factor

- 70mm (2.76”) x 70mm (2.76”)

• Compliance

- Qseven specification revision 1.2

PROCESSOR / MEMORY / TEMPERATURE / SSD

Model Processor Memory Temperature SSD Onboard

QB701-B620T102 Intel®Atom E620T 1GB DDR2 onboard -20oC to 70oC-

QB701-B640T102 Intel®Atom E640T 1GB DDR2 onboard -20oC to 70oC-

QB701-B660T102 Intel®Atom E660T 1GB DDR2 onboard -20oC to 70oC-

QB701-B680T102 Intel®Atom E680T 1GB DDR2 onboard -20oC to 70oC-

QB701-B620T012 Intel®Atom E620T 512MB DDR2 onboard -20oC to 70oC 2GB

QB701-B640T122 Intel®Atom E640T 1GB DDR2 onboard -20oC to 70oC 4GB

QB701-B680T202 Intel®Atom E680T 2GB DDR2 onboard -20oC to 70oC-

QB701-B620100 Intel®Atom E620 1GB DDR2 onboard 0oC to 60oC-

QB701-B640100 Intel®Atom E640 1GB DDR2 onboard 0oC to 60oC-

QB701-B660100 Intel®Atom E660 1GB DDR2 onboard 0oC to 60oC-

QB701-B680100 Intel®Atom E680 1GB DDR2 onboard 0oC to 60oC-

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI SD330-H110 Bedienungsanleitung

DFI

DFI NB71-BC Bedienungsanleitung

DFI

DFI CL630-CRM Bedienungsanleitung

DFI

DFI ADS310-R680E/Q670E Bedienungsanleitung

DFI

DFI G586VPA Bedienungsanleitung

DFI

DFI PT880-ALE Bedienungsanleitung

DFI

DFI LanParty KT400A Bedienungsanleitung

DFI

DFI G586OPC/E Bedienungsanleitung

DFI

DFI LT600-DR/D/L Bedienungsanleitung

DFI

DFI COM331-B Bedienungsanleitung

DFI

DFI COM630-B Bedienungsanleitung

DFI

DFI M8MP553 Bedienungsanleitung

DFI

DFI KD300-H110 Bedienungsanleitung

DFI

DFI SB331-D Bedienungsanleitung

DFI

DFI CMS310-W480E Bedienungsanleitung

DFI

DFI WL053 Bedienungsanleitung

DFI

DFI CA63-SN Bedienungsanleitung

DFI

DFI CA64-TC Bedienungsanleitung

DFI

DFI KM400A-MLV Bedienungsanleitung

DFI

DFI HD310-Q87 Bedienungsanleitung

DFI

DFI PB61-ZX Bedienungsanleitung

DFI

DFI 852GME-MGF Pro Bedienungsanleitung

DFI

DFI AK74-SC Bedienungsanleitung

DFI

DFI Infinity NF-ULTRA-M2 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung