Digi XTend vB DigiMesh XTP9B-DPM-001 Bedienungsanleitung

XTend vB DigiMesh RF Module

User Guide

Radio Frequency (RF) Module

User Guide

This datasheet has been downloaded fromhttp://www.digchip.com at this page

Revision history

900001479 A

Revision Date Description

A December 2015 Baseline release of the document.

Trademarks and copyright

Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States

and other countries worldwide. All other trademarks mentioned in this document are the property of their

respective owners.

Disclaimers

Information in this document is subject to change without notice and does not represent a commitment

on the part of Digi International. Digi provides this document “as is,” without warranty of any kind,

expressed or implied, including, but not limited to, the implied warranties of fitness or merchantability for

a particular purpose. Digi may make improvements and/or changes in this manual or in the product(s)

and/or the program(s) described in this manual at any time.

Warranty

To view the product's warranty information, go to the following website:

http://www.digi.com/howtobuy/terms

Customer support

Telephone (8:00 am — 5:00 pm U.S. Central Time):

Toll-free US and Canada: 866.912.3444

Worldwide: +1 952.912.3456

Online: www.digi.com/support/eservice

Mail:

Digi International Inc.

11001 Bren Road East

Minnetonka, MN 55434

USA

XTend vB DigiMesh RF Module User Guide 2

XTend vB DigiMesh RF Module User Guide 3

Contents

Revision history 2

The XTend vB RF Module

About the XTend vB RF Module 9

XTend replacement numbers 9

Certification overview 9

Technical specifications 10

General specifications 10

Performance specifications 10

Networking specifications 11

Power requirements 11

Regulatory approvals 12

Hardware

Connect the hardware 13

Mechanical drawings 14

Pin signals 15

XTend vB RF Module Modes

Transparent and API operating modes 19

Transparent operating mode 19

API operating mode 19

Receive mode 20

Transmit mode 20

Command mode 21

Enter Command mode 21

XTend vB DigiMesh RF Module User Guide 4

Send AT commands 21

Apply command changes 22

Exit Command mode 22

Operation

Serial interface 23

UART data flow 23

Serial data 24

Flow control 24

Data In (DIN) buffer and flow control 25

Data Out (DO) buffer and flow control 26

Networking methods

The MAC and PHY layers 27

64-bit address 28

Make a unicast transmission 28

Delivery methods 29

Point to Point / Point to Multipoint (P2MP) 29

Repeater / directed broadcast 29

DigiMesh networking 30

AT commands

Addressing commands 34

CI (Cluster ID) 34

DH (Destination Address High) 34

DL (Destination Address Low) 35

NI (Node Identifier) 35

NO(Network Discovery Options) 35

NT (Network Discovery Back-off) 36

SH (Serial Number High) 36

SL (Serial Number Low) 36

TO (Transmit Options) 37

Command mode options 38

CC (Command Sequence Character) 38

CT (Command mode Timeout) 38

GT (Guard Times) 38

Diagnostic commands 39

%H (MAC Unicast One Hop Time) 39

XTend vB DigiMesh RF Module User Guide 5

%V (Board Voltage) 39

%8 (MAC Broadcast One Hop Time) 39

BC (Bytes Transmitted) 40

DB (Last Packet RSSI) 40

EA (MAC ACK Failure Count) 40

ER (Receive Count Error) 41

GD (Good Packets Received) 41

RC 41

R# (Reset Number) 42

TR (Transmission Failure Count) 42

UA(Unicasts Attempted Count) 43

Firmware commands 43

CK (Configuration CRC) 43

DD (Device Type Identifier) 43

NP (Maximum Packet Payload Bytes) 44

HV (Hardware Version) 44

VR (Firmware Version) 44

I/O settings commands 44

CD (GP02 Configuration) 44

CS (GP01 Configuration) 45

RP (RSSI PWM Timer) 46

RT (GPI1 Configuration) 47

I/O diagnostic commands 47

TP (Board Temperature) 47

MAC/PHY commands 47

HP (Preamble ID) 48

ID (Network ID) 48

MT(Broadcast Multi-Transmits) 48

PL (TX Power Level) 48

RR (Unicast Retries) 49

Network commands 49

BH (Broadcast Hops) 49

CE (Routing / Messaging Mode) 50

MR (Mesh Unicast Retries) 50

NH (Network Hops) 51

NN (Network Delay Slots) 51

Security commands 51

EE (Encryption Enable) 51

KY (AES Encryption Key) 52

Serial interfacing commands 52

XTend vB DigiMesh RF Module User Guide 6

AO (API Options) 52

AP (API Enable) 53

BD (Baud Rate) 53

FT (Flow Control Threshold) 55

NB (Parity) 55

RB (Packetization Threshold) 55

RO (Packetization Timeout) 56

SB (Stop Bits) 57

XTend vB RF ModuleSpecial commands 57

AC (Apply Changes) 57

CN (Exit Command mode) 57

FR (Software Reset) 58

RE (Restore Defaults) 58

WR (Write) 58

R1 (Restored Compiled) 58

Operate in API mode

API mode overview 60

API frame specifications 60

Calculate and verify checksums 62

Escaped characters in API frames 62

API frames 63

API frame exchanges 64

Code to support future API frames 65

AT Command frame 0x08 66

AT Command - Queue Parameter Value frame 0x09 67

Legacy TX Request frame 0x00 69

Transmit Request frame 0x10 71

Explicit Addressing Command frame 0x11 74

Remote AT Command Request frame 0x17 78

AT Command Response frame 0x88 81

Modem Status frame 0x8A 82

Transmit Status frame 0x8B 83

Legacy TX Status frame 0x89 85

Route Information Packet 0x8D 86

Aggregate Addressing Update frame 0x8E 91

Legacy RX Indicator frame 0x80 93

RX Indicator frame 0x90 96

Explicit Rx Indicator frame 0x91 98

XTend vB DigiMesh RF Module User Guide 7

Node Identification Indicator frame 0x95 101

Remote Command Response frame 0x97 105

Work with networked devices

Network commissioning and diagnostics 108

Configure devices 108

Configure a device remotely 108

Send a remote command 108

Apply changes on remote devices 109

Remote command response 109

Establish and maintain network links 109

Build aggregate routes 109

Examples 110

Replace nodes 111

Test links in a network 111

Test links between adjacent devices 112

Example 114

RSSI indicators 114

Discover devices 115

Trace route option 116

NACK messages 117

Certifications

FCC (United States) 118

OEM labeling requirements 118

FCC notices 118

FCC antenna certifications 119

Antenna options 120

Industry Canada (IC) 127

Labeling requirements 127

Transmitters for detachable antennas 128

Detachable antennas 128

ACMA (Australia) 128

Power requirements 128

Development Kit

Development Kit contents 130

Interface hardware 131

XTend vB DigiMesh RF Module User Guide 8

XTIB-R RS-232/485 Interface Board 132

Configuration switch 133

I/O and Power LEDs 133

Serial port 133

RSSI LEDs 133

Power connector 134

XTIB-R Dip switch 134

Adapters 135

NULL Modem Adapter (male-to-male) 135

NULL Modem Adapter (female-to-female) 135

Serial Loopback Adapter 136

Male DB-9 to RJ-45 Adapter 136

Female DB-9 to RJ-45 Adapter 137

Interface protocols 137

RS-232 operation 137

RS-485 (2-wire) operation 141

RS-485 (4-wire) and RS-422 operation 143

XTend vB DigiMesh RF Module User Guide 9

The XTend vB RF Module

About the XTend vB RF Module

The XTend vB RF Module was engineered to provide customers with an easy-to-use radio frequency (RF)

solution that provides reliable delivery of critical data between remote devices. The module transfers a

standard asynchronous serial data stream, operates within the ISM 900 MHz frequency band and operates

at an RF data rate of 125 kb/s.

XTend replacement numbers

The following table provides the part numbers you can use to replace XTend devices with the XTend vB RF

Module.

Legacy part number Replacement part number

XT09-MI XTP9B-DPM-001

XT09-SI XTP9B-DPS-001

XT09-MI-MESH XTP9B-DMM-001

XT09-SI-MESH XTP9B-DMS-001

Certification overview

The XTend vB RF Module contains an FCC/IC approved RF module. For usage requirements, see

Certifications on page 118.

ISM (Industrial, Scientific and Medical) license-free 902-928 MHz frequency band.

Manufactured under ISO 9001:2000 registered standards.

Technical specifications

XTend vB DigiMesh RF Module User Guide 10

Technical specifications

The following tables provide the device's technical specifications.

When operating at 1 W power output, observe a minimum separation distance of 6 ft (2 m)

between devices. Transmitting in close proximity of other devices can damage the device's

front end.

General specifications

The following table provides the general specifications for the device.

Specification Value

Dimensions (RF/pin connectors not included) 1.46 x 2.40 x 0.190 in (3.7 x 6.1 x 4.8 cm)

Weight 16 g

RoHS Compliant

Manufacturing ISO 9001:2000 registered standards

Connector 20 pin 2 mm pitch header

Antenna connector options MMCX or RPSMA

Antenna impedance 50 ohms unbalanced

Operating temperature -40°C to 85°C

Maximum input RF level at antenna port 6 dBm

Performance specifications

The following table provides the performance specifications for the device.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digi Steuereinheit Handbücher

Digi

Digi INFOTAG 2.13 Bedienungsanleitung

Digi

Digi XBee Bedienungsanleitung

Digi

Digi ConnectCore 9P 9215 Anwendungshandbuch

Digi

Digi XBee ZigBee S2C Bedienungsanleitung

Digi

Digi ConnectCore 7U Anwendungshandbuch

Digi

Digi XBee-PRO XSC Bedienungsanleitung

Digi

Digi XBee3 802.15.4 Bedienungsanleitung

Digi

Digi ConnectCore 6UL Kurzanleitung

Digi

Digi MiniCore RCM5700 Series Bedienungsanleitung

Digi

Digi Connect Wi-Wave Anwendungshandbuch

Digi

Digi XBee-PRO Bedienungsanleitung

Digi

Digi Connect Series Benutzerhandbuch

Digi

Digi ConnectCore 6 Plus Kurzanleitung

Digi

Digi XBP09-XC... Bedienungsanleitung

Digi

Digi XBee ZigBee S2C Bedienungsanleitung

Digi

Digi Digi Conntect ME Anwendungshandbuch

Digi

Digi XBee 868LP Bedienungsanleitung

Digi

Digi XBee ZNet 2.5 Bedienungsanleitung

Digi

Digi ConnectCore 9M 2443 Anwendungshandbuch

Digi

Digi ConnectCore XP 270 Anwendungshandbuch

Digi

Digi XBee3-PRO Micro Kurzanleitung

Digi

Digi XBee Bedienungsanleitung

Digi

Digi Connect Wi-ME 9210 Bedienungsanleitung

Digi

Digi XBee Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung