Digitus 4-CHANNEL SATA II Bedienungsanleitung

4-CHANNEL SATA II

PCI EXPRESS CARD

User Manual

Features

Marvell 88SX7042 chipset

Compliant with PCI Express Base Specification 1.0a

Compliant with Serial ATA 1.0 specification with support for full

complement of SATA II optional features

Supports SATA II Native Command Queuing (NCQ)

Provides four independent channels to support up to four Serial

ATA drives

Supports SATA up to 300MB/Sec

Supports Windows 7, Vista, XP, 2000

Bus Interface

PCI-Express x 4

Connectors

4 x internal SATA connectors

2 x external eSATA connectors

System Requirements

PCI Express-enabled system with one available PCI Express slot

Windows 7, Vista, XP, 2000

Hardware Description

G (Jumper Settings)

JP Description Active Port

J2-J5 1-2 close Enable SATA Connector D

2-3 close Enable SATA Connector E

J6-J9 1-2 close Enable SATA Connector C

2-3 close Enable SATA Connector F

Note: There are six SATA ports in PCIe SATA II 300 4-Channel

Adapter. We name these ports A to F. Ports A to D are internal SATA

ports and E & F are external SATA ports. By changing the jumper

setting on the PCIe SATA II 300 4-Channel Adapter that allows you to

select between external and internal ports to use. By default, Port A, B,

C and D are working.

Hardware Installation

1. Turn Off the power to your computer and any other connected

peripheral devices.

2. Unplug the power cord from the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI Express slot.

5. To install the card, carefully align the card’s bus connector with

the selected PCI Express slot on the motherboard. Push the board

down firmly, but gently, until it is well seated.

6. Replace the slot bracket’s holding screw to secure the card.

Device Connection

The PCIe SATA II 300 4-Channel Adapter is a four channel Serial ATA

controller that supports up to four Serial ATA hard disk drives.

1. Install your hard disk drive(s) in chassis.

2. Connect the Serial ATA hard disk drive to the system power

supply using the included Serial ATA power cable.

3. Connect one end of the Serial ATA cable to the hard disk drive.

4. Attach the other end of the Serial ATA cable to the Serial ATA

controller on the PCIe SATA II 300 4-Channel Adapter.

5. Follow the same instructions to connect up to four hard drives.

Device connection is now complete.

6. Replace the computer cover and reconnect the power cord.

Driver Installation

For Windows® 2000

For A New Installation

A new installation requires a floppy disk for the driver

installation. To make this floppy disk, copy the contents of

the “DS-30104\2K_XP_2003_Vista” folder, found on the driver CD,

onto a blank floppy disk then follow the directions below.

1. Follow Windows® 2000 installation procedure.

2. Restart the computer when prompted by the installation.

3. At the Windows® 2000 Setup screen, press F6 to install the

driver.

4. When prompted, press S to specify the location of the driver.

5. Insert the floppy disk, then press Enter.

6. Select Marvell Serial ATAAdapter , then press Enter.

7. Press Enter again to finish driver installation, then follow the

on-screen instructions to complete the Windows installation.

ForAn Existing Installation

1. At Found New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device(recommend)

then click Next.

3. Insert the driver CD, check CD-ROM drives, uncheck the other

boxes, click Next, then click Next again.

4. If the Digital Signature Not Found message appears, click Yes.

Our driver has been thoroughly tested for stability and

compatibility.

5. Click Finish.

For Windows® XP/Server 2003

For New Installation

A new installation requires a floppy disk for the driver

installation. To make this floppy disk, copy the contents of

the “DS-30104\2K_XP_2003_Vista” folder, found on the driver CD,

onto a blank floppy disk then follow the directions below.

1. Follow Microsoft’s Windows installation procedure.

2. Restart the computer when prompted by Windows’ installation.

3. At the Windows Setup screen, press F6 to install the driver.

4. When prompted, press S to specify the location of the driver.

5. Insert the floppy disk, then press Enter.

6. Select Marvell Serial ATAAdapter, then press Enter.

7. Press Enter to finish driver installation, then follow the on-screen

instructions to complete the Windows installation.

Note: If the Security Alert warning pops up, click Yes. Our driver has

passed Microsoft compatibility testing, this message appears during

new installation.

For An Existing Installation

1. At the Found New Hardware Wizard:

XP (w/SP1 or earlier)/Server 2003: continue to step #2

XP (w/SP2 or later)/Server 2003(w/SP1 or later): select No,

not this time, then click Next.

2. Insert the driver CD, select Install the software

automatically (Recommended), and click Next.

3. If the Hardware Installation window pops up, click Continue

Anyway, then Finish. Our driver has been thoroughly tested

for stability and compatibility.

4. Click Finish

For Windows® XP-x64/Server 2003-x64

For New Installation

A new installation requires a floppy disk for the driver

installation. To make this floppy disk, copy the contents of

the “DS-30104\XP_2003_Vista x64” folder, found on the driver CD,

onto a blank floppy disk then follow the directions below.

1. Follow Microsoft’s Windows installation procedure.

2. Restart the computer when prompted by Windows’ installation.

3. At the Windows Setup screen, press F6 to install the driver.

4. When prompted, press S to specify the location of the driver.

5. Insert the floppy disk, then press Enter.

6. Select Marvell Serial ATAAdapter, then press Enter.

7. Press Enter to finish driver installation, then follow the on-screen

instructions to complete the Windows installation.

Note: If the Security Alert warning pops up, click Yes. Our driver has

passed Microsoft compatibility testing, this message appears during

new installation.

ForAn Existing Installation

1. At the Found New Hardware Wizard, select No, not this time,

then click Next.

2. Insert the driver CD, select Install the software automatically

(Recommended), and click Next.

3. If the Hardware Installation window pops up, click Continue

Anyway, then Finish. Our driver has been thoroughly tested for

stability and compatibility.

4. Click Finish.

For Windows® Vista

For New Installation

A new installation requires a floppy disk for the driver

installation. To make this floppy disk, copy the contents of

the “DS-30104\2K_XP_2003_Vista” folder, found on the driver CD,

onto a blank floppy disk then follow the directions below.

1. Follow Microsoft’s Windows installation procedure.

2. Restart the computer when prompted by Windows’ installation.

3. At the Windows Setup screen, press Load Driver to install the

driver.

4. Insert the floppy disk, please select Marvell Serial ATA Gen 2

PCI Express Adapter (A:\mvsata.inf), then press Next. (Change

A:\ to match your floppy drive letter)

5. Follow the on-screen instructions to complete the

Windows installation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus PCI-Karte Handbücher

Digitus

Digitus DS-30226 Bedienungsanleitung

Digitus

Digitus DS-30040-2 Bedienungsanleitung

Digitus

Digitus USB 2.0, 4+1 Port PCI Add-On card Bedienungsanleitung

Digitus

Digitus DS-33203-2 Bedienungsanleitung

Digitus

Digitus Wireless 150N PCI Adapter Bedienungsanleitung

Digitus

Digitus DN-10131 Bedienungsanleitung

Digitus

Digitus DS-30221-1 Bedienungsanleitung

Digitus

Digitus DS-33002-1 Bedienungsanleitung

Digitus

Digitus DS-30020-1 Bedienungsanleitung

Digitus

Digitus DS-30000-1 Bedienungsanleitung

Digitus

Digitus DS-30040-2 Bedienungsanleitung

Digitus

Digitus DS-33101-1 Bedienungsanleitung

Digitus

Digitus DS-30201-4 Bedienungsanleitung

Digitus

Digitus DS-30222 Bedienungsanleitung

Digitus

Digitus DS-30040 Bedienungsanleitung

Digitus

Digitus DS-33102-1 Bedienungsanleitung

Digitus

Digitus DS-33160 Bedienungsanleitung

Digitus

Digitus PCI-Add-On-Card Firewire IEEE1394 Bedienungsanleitung

Digitus

Digitus DS-30040-2 Bedienungsanleitung

Digitus

Digitus DN-10133 Bedienungsanleitung

Digitus

Digitus DS-30220-3 Bedienungsanleitung

Digitus

Digitus Firewire 800 Bedienungsanleitung

Digitus

Digitus FIREWIRE 800 Bedienungsanleitung

Digitus

Digitus Serial ATA RAIDPCI Card Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung