Digitus Serial ATA RAIDPCI Card Bedienungsanleitung

Serial ATA RAID

PCI Card

User Manual

Features

Silicon Image SiI3512 SATA controller chip

Compliant with PCI Specification, Rev. 2.3

Compliant with Serial ATA 1.0 specification

Provides two independent channels to support up to two Serial

ATA drives

Supports RAID0(striping) and RAID1(mirroring) for speed and

data protection respectively

HDDs function normally when not in RAID sets

Supports SATA up to 150MB/Sec

Supports Windows® 7 / Vista 32 /64-Bit/ 2003 32/64-Bit /

XP /2000

Connectors

2 x internal SATA connectors

System Requirements

Pentium-class computer with one available PCI slot

Windows® 7 / Vista 32 /64-Bit/ 2003 32 /64-Bit / XP /2000

Hardware Installation

1. Turn Off the power to your computer and any other connected

peripheral devices.

2. Unplug the power cord form the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card’s bus connector with

the selected PCI slot on the motherboard. Push the board down

firmly, but gently, until it is well seated.

6. Replace the slot bracket’s holding screw to secure the card.

Device Connection

The SATA 150 PCI RAID Card is a two channel Serial ATA controller

that supports up to two Serial ATA hard disk drives. It is recommended

to use identical hard drives for all RAID configurations.

1. Install your hard disk drive(s) in chassis.

2. Connect the Serial ATA hard disk drive to the system power

supply using the included Serial ATA power cable.

3. Connect one end of the Serial ATA cable to the hard disk drive.

4. Attach the other end of the Serial ATA cable to the Serial ATA port

on the SATA 150 PCI RAID Card.

5. Follow the same instructions to connect up to two hard drives.

Device connection is now complete.

6. Replace the computer cover and reconnect the power cord.

RAID Arrays

RAID Arrays are setup in the SATA 150 PCI RAID Card’s BIOS.

RAID 0 (Striping)

This RAID array to be used on New/Blank hard drives. Striping will

destroy existing data on the hard drive. Auto Configuration is

recommended. For applications that require custom chunk size,

Manual Configuration is offered.

Auto configuration (recommended)

The default chunk size is 64k when selecting Auto configuration.

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter

the RAID BIOS.

2. At the next screen select Create RAID Set, then press Enter.

3. Select Striped, then press Enter.

4. Select Auto configuration, then press Enter.

5. When asked Are You Sure (Y/N)?, press Y to accept.

6. Press Ctrl+E to exit the BIOS.

7. When asked Are you sure to exit (Y/N)?, press Y to exit and

reboot.

8. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

Manual configuration

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter

the RAID BIOS.

2. At the next screen select Create RAID Set, then press Enter.

3. Select Striped, then press Enter.

4. Select Manual configuration then press Enter

5. Select the first drive, press Enter.

6. Select the second drive, press Enter.

7. Select chunk size from 4k, 8k, 16k, 32k, 64k or 128k, then press

Enter.

8. When asked Are You Sure(Y/N)?, press Y to accept.

9. Press Ctrl+E to exit the BIOS.

10. When asked Are you sure to exit(Y/N)?, press Y to exit and

reboot.

11. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

RAID 1 (Mirror)

For New/Blank Hard Drives

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter

the RAID BIOS.

2. At the next screen select Create RAID Set, then press Enter.

3. At the next screen select Mirrored then press Enter.

4. Select Auto configuration, then press Enter.

5. When asked Are You Sure(Y/N)?, press Y to accept.

6. Press Ctrl+E to exit the BIOS.

7. When asked Are you sure to exit(Y/N)?, press Y to exit and

reboot.

8. Continue with FDISK and FORMAT steps as if you were

installing a conventional hard drive.

For Existing Hard Drives with Data

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter

the RAID BIOS.

2. At the next screen select Create RAID Set, then press Enter.

3. At the next screen select Mirrored then press Enter.

4. Select Manual configuration, then press Enter.

5. Select the Source drive, press Enter.

6. Select the Target drive, press Enter.

7. Enable Disk Copy, select Yes, then press Enter.

Note: Enable Disk Copy – Copy current content of source driver to

mirror drive; Disable Disk Copy – RAID 1 set formed must be

repartitioned and reformatted to guarantee the consistency in their

contents.

8. Press Ctrl+E to exit the BIOS.

9. When asked Are you sure to exit(Y/N)?, press Y to exit and

reboot.

Note: If during boot the RAID BIOS reports an RAID1 set is in

Rebuild status, The rebuild will continue after boot sequence is

complete, disregard the message, continue booting, and let the Mirror

rebuild.

Rebuilding a Failed Mirror Set

When a failure to one member occurs, you will be notified either by the

RAID BIOS during boot or by the SATARAID GUI while in

Windows. The steps below will guide you in rebuilding a failed mirror

set.

1. Replace the failed drive with one of equal or greater capacity, then

start the computer.

2. During boot press Ctrl+S or F4 to enter the RAID BIOS.

3. Select Rebuild Mirrored Set then press Enter.

4. Select the desired set and then press Enter.

5. When asked Are You Sure(Y/N)?, press Y to confirm.

6. The set will be rebuilt.

Deleting RAID Arrays

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter

the RAID BIOS.

2. Select Delete RAID Set, then press Enter.

3. Select the RAID set then press Enter.

4. When asked Are You Sure(Y/N)?, press Y to confirm.

Resolving Conflicts

When a RAID set is created, then metadata written to the disk includes

drive connection information. If, after a disk failure, the replacement

disk was previously part of a RAID set (or used in another system), it

may have conflicting metadata. If so, this will prohibit the RAID set

from being either created or rebuilt, in order for the RAID set to

function properly, this old metadata must be first overwritten with the

new metadata. To resolve this, from the main BIOS window select

Resolve Conflicts, then press Enter, the correct metadata, including

the correct drive connection information, will be written to the

replacement disk.

Low Level Format

Low Level Format is build into the RAID BIOS to make it more

convenient to erase the entire contents of a hard disk drive, including

data, drive and partition information. The Low Level Format utility

works on single hard drive only, before the RAID set is configured.

BIOS Configuration

The Serial ATA 2-Channel RAID adapter BIOS will appear every time

your system starts up. If the BIOS doesn’t show, please try your

controller in another PCI slot. During this (POST) process, the BIOS

will show up and indicate the devices attached to it.

Driver Installation

For Windows® 2000

For A New Installation

A new installation requires a floppy disk for the driver

installation. To make this floppy disk, copy the contents of

the “DS-33101\2K_XP_2003_Vista” folder, found on the driver CD,

onto a blank floppy disk then follow the directions below.

1. Setup the RAID Array prior to Windows installation.

2. Follow Windows® 2000 installation procedure.

3. Restart the computer when prompted by the installation.

4. At the Windows® 2000 Setup screen, press F6 to install the RAID

driver.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus PCI-Karte Handbücher

Digitus

Digitus DS-30000-1 Bedienungsanleitung

Digitus

Digitus DN-7066 Bedienungsanleitung

Digitus

Digitus DS-30020-1 Bedienungsanleitung

Digitus

Digitus DS-30220-3 Bedienungsanleitung

Digitus

Digitus DS-30040-2 Bedienungsanleitung

Digitus

Digitus FIREWIRE 800 Bedienungsanleitung

Digitus

Digitus DS-30201-4 Bedienungsanleitung

Digitus

Digitus DS-30201-5 Bedienungsanleitung

Digitus

Digitus DN-10110 Bedienungsanleitung

Digitus

Digitus DS-33156 Bedienungsanleitung

Digitus

Digitus DS-30103 Bedienungsanleitung

Digitus

Digitus DS-30040-2 Bedienungsanleitung

Digitus

Digitus DS-33170 Bedienungsanleitung

Digitus

Digitus DS-33170 Bedienungsanleitung

Digitus

Digitus DS-33102-1 Bedienungsanleitung

Digitus

Digitus MULTI I/O COMBI PCI ADD-ON CARD Bedienungsanleitung

Digitus

Digitus DS-33003 Bedienungsanleitung

Digitus

Digitus DS-30221-1 Bedienungsanleitung

Digitus

Digitus DS-30225 Bedienungsanleitung

Digitus

Digitus Firewire 800 Bedienungsanleitung

Digitus

Digitus DS-33103 Bedienungsanleitung

Digitus

Digitus DS-30000-1 Bedienungsanleitung

Digitus

Digitus USB 2.0, 4+1 Port PCI Add-On card Bedienungsanleitung

Digitus

Digitus DS-33101-1 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung