DITEC PASP Bedienungsanleitung
PASP
1
2
5
6
7
3
4
* Other use of the device outside of the permitted purpose can not be guaranteed by the manufacturer.
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
PASSIVE INFRARED SENSOR FOR AUTOMATIC
DOORS*
Specifications are subject to changes without prior notice.
Measured in specific conditions.
Technology :
Optical characteristics:
Maximum Detection area (mounting height: 2.2m):
Minimum Detection area (mounting height: 2.2 m)
Detection mode:
Detection speed:
Light indicator:
Warm up time:
Hold time:
Response time:
Power supply:
Frequency:
Power consumption:
Connection:
Recommended cable section (terminal block):
Standard output:
Max. contact voltage:
Max. contact current:
Max. switching power:
Mounting height:
Temperature range:
Dimensions:
Sensor:
Entrematic PASP:
Color (Sensor-PASP):
Length of cable:
Conformity:
passive infrared and microprocessor
P.I.R. with 4 elements, 15 lenses with full independent masking possibilities
2.5 m (W) x 1.5 m (D)
0.5 m (W) x 0.5 m (D)
motion
0.1 to 1.5 m/s
1 red LED:flashes for a few seconds after power-on
LED lights up: sensor detects motion
10 s
0.5 s ou 2 s
< 200 ms
12 VDC - 10% à 24VDC +30% /12 to 24 V AC ±10%
50/60 Hz
< 1 W
terminal block
< 0.5 mm²
relay (free potential contact)
60 V DC / 42 V AC
1A (resistive)
30W (DC) / 42 VA (AC)
3 m max
from -30 °C to +55 °C
101 mm (W) x 41 mm (H) x 27 mm (D)
121 mm (W) x 51 mm (H) x 40 mm (D)
anthracite grey
2.5 m
EN 61000-6-2; EN 61000-6-3; EN 50581
User’s Guide for product version 0202 and higher
See product label for serial number.
PLEASE KEEP FOR FURTHER USE
DESIGNED FOR COLOUR PRINTING
1. Sensor fixing
screw (black)
2. LED
3. DIP-switch
4. Lens
5. Terminal block
6. Bracket
7. bracket
fixing screw
(aluminium)
1
2
PASP
PASP
OPENING AND CLOSING THE SENSOR
MOUNTING THE SENSOR
To open the sensor, insert a screwdriver in the hole
under the bracket cam.
Consider the position of the guide pin when
closing the sensor.
Insert the bottom of the front cover to the bottom
clip of the base and push to close the sensor.
To remove the cover, insert a screwdriver as shown
(left) or pinch off both sides of the front cover (right).
1. Stick the template to the internal profile.
2. Drill the 2 holes.
3. Fix the brackets to both sides of the sensor with the 2 aluminum screws.
4. Fix the sensor, with the connector facing you, to the profile with the 2
black screws.
5. Make the cut-out in the door profile.
6. Connect the sensor using the cable (See p. 1 for wiring).
7. Adjust the tilt angle using the brackets.
1. Stick the template to the wall.
2. Drill the 2 holes to fix the sensor and the hole for the cable.
3. Open the sensor and cut out a wire opening footprint.
4. Fix the sensor to the base with the 2 aluminum screws supplied
with the PASP.
5. Connect the sensor using the cable.
6. Fix the sensor with the 2 black screws and close the sensor.
SENSOR
SENSOR FRONT COVER
1. Stick the template to the ceiling and cut out the hole.
2. Clip the sensor on the FCA and fix it with the 2 washers and the 2
aluminum screws.
3. Connect the sensor using the cable.
4. Insert the complete assembly into the ceiling and fix it using the 2
long, black screws.
3
4
PASP
ON
1
2 3
1
2
DIP SWITCH SETTINGS
ON
OFF
DIP SWITCH #1 DIP SWITCH #2 DIP SWITCH #3
Sensitivity high
Sensitivity low
(mounting height< 2.2m)
Passive output (NC)
Active output (NO)
Hold time: 2 s
Hold time: 0.5 s
The drawings show the maximum sensing field dimensions. If you install the PASP without accessories, you can move
the sensing field position by tilting the sensor to select the required vertical tilt angle. Otherwise, this adjustment is
not possible.
To adjust the sensing field, use the
masking lens. To tailor the sensing
field, cut the segments.
Use the guide pins to insert the
masking lens on the front cover.
Position the screwdriver as shown
to remove the masking lens.
SENSING FIELD SETTINGS
EXAMPLES: door threshold
door threshold
DETECTION AREA
NO DETECTION
NO DETECTION
DETECTION AREA
FRONT VIEW
FLAT VIEW
Door threshold
height
1
1
1
1
1
ASSA ABLOY Entrance Systems AB - Lodjursgatan 10 - SE-261 44 Landskrona - Sweden - www.ditecautomations.com
ASSA ABLOY Entrance Systems AB hereby declares that the PASP is in conformity with the basic requirements and the
other relevant provisions of the directives 2014/30/EU and 2011/65/EU.
Landskrona, January 2021 Matteo Fino, authorized representative and responsible for technical documentation.
The complete declaration of conformity is available on our website.
TROUBLESHOOTING
This product should be disposed of separately from unsorted municipal waste
INSTALLATION TIPS
The sensor must be firmly
fastened in order to avoid
vibrations!
When mounting the
PASP, make sure you apply the
brackets before tightening
the screws.
Always use the aluminium
screws to fasten the
accessories and the black
screws to fix the sensor.
Using the wrong screws could
damage the sensor!
The door remains
closed. The LED is OFF.
The door will not open
and the LED lights up.
The door opens when
no detection occurs
and closes during
detection.
The sensing field does
not correspond to your
requirements.
The detection is very
bad.
The sensor power is off.
The mode of the relay output
is not correct.
The cut of the masking lens
is wrong.
The sensor might be installed
upside down.
The wiring of the relay
output is not connected
correctly.
Check the wiring and the power supply. check the
supplied voltage.
Check the relay wiring.
Change the position of dip-switch 2.
Cut out a new lens to meet the required sensing
field size.
Check if the sensor is installed with its connector
facing you.
©ASSA ABLOY Entrance Systems AB I Original instructions | 47.0463 / V1 - 05.21
Dieses Handbuch passt für folgende Modelle
1
Andere DITEC Türöffnungssystem Handbücher
DITEC
DITEC ENTREMATIC HA9 Bedienungsanleitung
DITEC
DITEC VALOR HH-HS Bedienungsanleitung
DITEC
DITEC OLLY C Handbuch
DITEC
DITEC Sprint Bedienungsanleitung
DITEC
DITEC DAB105 Bedienungsanleitung
DITEC
DITEC DOR Bedienungsanleitung
DITEC
DITEC Entrematic ENERGY 49E Benutzerhandbuch
DITEC
DITEC BIS O Handbuch
DITEC
DITEC DAS107PLUS Bedienungsanleitung
DITEC
DITEC DAS107PLUS Bedienungsanleitung
DITEC
DITEC ENTREMATIC HA9 Service-Handbuch
DITEC
DITEC DAS200TRF Bedienungsanleitung
DITEC
DITEC VALOR Bedienungsanleitung
DITEC
DITEC CIVIK Series Handbuch
DITEC
DITEC DOD Bedienungsanleitung
DITEC
DITEC DAS900FM Bedienungsanleitung
DITEC
DITEC DAB105 Bedienungsanleitung
DITEC
DITEC COM E Bedienungsanleitung
DITEC
DITEC 0DT848 Benutzerhandbuch
DITEC
DITEC DAB305 Bedienungsanleitung
