DMP Electronics 734 Installationsanleitung

INSTALLATION AND PROGRAMMING GUIDE

734 Wiegand

Interface Module

About the 734............................................. 1

Power Supply......................................................... 1

Zone Terminals ...................................................... 1

Annunciators.......................................................... 1

Indicator LEDs ....................................................... 1

Form C Relay......................................................... 2

Programming Connection................................ 2

Keypad In and Out Connections ................... 2

PCB Features...............................................3

Install the 734 .............................................4

Wire the Magnetic Lock.................................... 5

Isolation Relay (optional) ................................. 7

Install the 333 Suppressor ............................... 8

Wire the Zone Terminals................................... 9

Connect a Card Reader (optional) ............... 11

Set the 734 Address..........................................14

TABLE OF CONTENTS

Program the 734....................................... 17

Program Start Display ......................................18

Initialization Option ...........................................18

Initialize Conﬁrm Option .................................18

Activate Zone 2 Bypass...................................19

Zone 2 Bypass Time.........................................20

Relock on Zone 2 Change..............................20

Activate Zone 3 Request to Exit ..................21

Zone 3 REX Strike Time..................................22

Activate Onboard Speaker............................ 22

Card Formats ......................................................22

Custom Card Deﬁnitions .........................23

Card Format Number.......................................23

Format Name......................................................24

Wiegand Code Length....................................24

Site Code Position and Length .................... 25

User Code Position and Length...................25

Require Site Code .............................................26

Site Code Display ..............................................26

Number of User Code Digits......................... 27

No Communication with Panel ....................28

Remove Keypad.................................................29

Keypad Bus Wiring Speciﬁcations........ 30

Public Card Formats ................................ 31

Compliance Listing Speciﬁcations ........32

UL Commercial Fire..........................................32

UL Access Control.............................................32

ULC Commercial Burglary (XR150/XR550

Series Panels)......................................................33

Certiﬁcations............................................ 34

Underwriters Laboratory (UL Listed)........34

Product Speciﬁcations ............................35

Readers and Credentials ........................ 36

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 1

Annunciators

An onboard programmable piezo provides

local annunciation at the 734. You can

also connect a variety of switched ground

annunciators to the 734 for remote

annunciation.

Indicator LEDs

The 734 provides three indicator LEDs. The

red LED turns on for the same duration

as the door strike relay. The yellow LED

turns on for one second to indicate receipt

of a valid Wiegand input. The green LED

indicates that data is being sent to the

panel.

The 734 Wiegand Interface Module allows you to use the powerful built‑in access control

capability of DMP Panels. DMP panels provide access control, arming, and disarming

using proximity, mag‑stripe, biometric, or other Wiegand‑output authentication devices.

Connect a 734 to a DMP panel’s keypad bus or AX‑Bus™ to use the powerful built‑in

access control capability of DMP panels. The 734 includes the following features:

Power Supply

The 734 operates at 12/24VDC from

the power supply supporting a door’s

magnetic lock or door‑strike.

Warning: To avoid the risk of

equipment damage, do not exceed

750mA total output current for zones

connected to the module.

Zone Terminals

Zones 1, 2, and 3 on the 734 can be

programmed for a variety of burglary

or access control applications. Zone 4

is a class B, style A circuit that may be

programmed as a ﬁre zone.

ABOUT THE 734

2 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

Form C Relay

The 10Amp Form C relay draws up to

35mA of current. Refer to the NC/C/NO

(Dry Contact Relay) and the Isolation

Relay sections in this document for more

information.

Programming Connection

The 734 also provides a keypad

programming connection that allows

you to use a standard DMP LCD keypad

for initial setup. Programming can be

completed using a keypad connected

to the 734 or from XR150/XR550 Series

panels.

Keypad In and Out

Connections

The keypad in (KYPD IN) connection

receives and transmits data to the panel

keypad bus or AX‑Bus.

The keypad out (KYPD OUT) connection

receives and transmits data out to other

keypads or modules. Install a dual

connector four‑position harness to allow

daisy chain connection to other devices,

up to the maximum number of devices

supported. XR150Series panels support

up to 8devices. XR550Series panels

support up to 16devices. When using the

AX‑Buses with XR550 devices, you can

have 32 doors, expandable to 96.

Caution: When the 734 is powered

from 24VDC, do not connect devices

to KYPD OUT header.

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 3

PCB FEATURES

RED

PROG

RED

KYPD OUT

DATA

XMT LED

WIEGAND

READ LED

RELAY

GRN

YEL

RED + –

Piezo

1234 5 6 7 810 11 12 13 14

LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND

KYPD IN RED

Door Relay

Terminal

Wiegand

Inputs

Status

Indicator

Outputs Zones

To Panel

Keypad Bus

or AX‑Bus

To Other

Keypad Bus

or AX‑Bus

Piezo

Indicator

LEDs

Keypad

Programming

Header

Address DIP

Switches

Figure1: PCB Features

4 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

INSTALL THE 734

Mount the 734

The module comes in a high‑impact plastic housing that you can mount directly to a

wall, backboard, or other ﬂat surface.

For easy installation, the back and ends of the 734 housing have wire entrances. The

back also contains multiple mounting holes that allow you to mount the module on a

single‑gang switch box. DMP recommends mounting the 734 near the protected door.

See Figure2 for mounting hole locations on the housing base.

1. Remove the PCB from the

plastic housing by loosening

the clips on one side and gently

lifting it out of the housing base.

2. Insert the included screws in the

desired mounting hole locations

and tighten them to secure the

housing to the surface.

3. Reinstall the PCB in the housing

base.

Mounting Holes

Figure2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 5

Wire the Magnetic Lock

The 734 provides a Form C (SPDT) relay for controlling locks and other

electronically‑controlled barriers. The three relay terminals marked NO C NC allow

you to connect the device wiring to the relay for module control.

Use an additional power supply to power magnetic locks and door strikes. See

Figures 3 and 4 for typical magnetic lock and door strike wiring.

The Form C relay draws up to 35mA of current and contacts are rated for 10Amps

(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the

total current for all locks cannot exceed 10Amps. If the total current for all locks

exceeds 10Amps, problems may arise and an isolation relay may be needed. See the

Isolation Relay section for information.

PROG

RED RED

KYPD IN

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED

Model 333

Suppressor

Normally Closed

–

Magnetic Door Lock

12/24 VDC

Power Supply

PROG

RED

DATA

XMT LED

WIEGAND

READ LED

RELAY

NCCNO

GRNYELRED

Model 333

Suppressor

Normally Open

–+

DC Door Strike

12/24 VDC

Power Supply

Figure4: Typical Door Strike WiringFigure3: Typical Magnetic Lock Wiring

6 734 Installation and Programming Guide | Digital Monitoring Products, Inc.

KYPD IN / KYPD OUT Connections

• KYPD IN (Keypad In): Receives and transmits data to the panel Keypad bus/AX‑

Bus.

• KYPD OUT (Keypad Out): Receives and transmits data out to other keypad(s) or

module(s). Install a dual‑connector harness to allow connection to other devices

up to the maximum number of devices supported.

When the 734 is powered from 24VDC, do not connect devices to KYPD OUT header.

Status LEDs

The 734 board contains three status LEDs.

• The Red LED turns on for the same duration as the door strike relay.

• The Yellow LED turns on for one second to indicate receipt of a valid Wiegand

input.

• The Green LED indicates data sent to the panel.

Andere Handbücher für 734

Inhaltsverzeichnis

Andere DMP Electronics Steuereinheit Handbücher

DMP Electronics

DMP Electronics 736P Radionics Installationsanleitung

DMP Electronics

DMP Electronics 716 Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics ITI 738I Installationsanleitung

DMP Electronics

DMP Electronics 734N-WIFI Administratorhandbuch

DMP Electronics

DMP Electronics 714-D22 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Installationsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G211 Bedienungsanleitung

DMP Electronics

DMP Electronics 734B Installationsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

DMP Electronics

DMP Electronics 861 Bedienungsanleitung

DMP Electronics

DMP Electronics 738Zplus Bedienungsanleitung

DMP Electronics

DMP Electronics 277CAN Bedienungsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G145 Bedienungsanleitung

DMP Electronics

DMP Electronics 893A Bedienungsanleitung

DMP Electronics

DMP Electronics 736V Bedienungsanleitung

DMP Electronics

DMP Electronics 717 Bedienungsanleitung

DMP Electronics

DMP Electronics 865 Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics 736P Radionics Bedienungsanleitung

DMP Electronics

DMP Electronics 738ZplusINT Bedienungsanleitung

DMP Electronics

DMP Electronics 734N Series Installationsanleitung

DMP Electronics

DMP Electronics 708 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung