Dynamic ULTRA PRO Bedienungsanleitung

Models:

400112

400112SB

400212

400212SB

700102

700102SB

700112

700112SB

700152

700202

700202SB

700212

700212SB

HALF RACK ASSEMBLY INSTRUCTIONS

Use the 5” carriage bolts

to mount chin station

on ULTRA PRO™ Models

ULTRA PRO™ TITAN G2

844-678-7447 www.MyDynamicFitness.com

Tools Required:

3/4” Standard Socket

3/8” Drive Ratchet

3/4” Combination End Wrench

All parts have a part number.

Position the part number to be

covered by its mating component

or up as shown in this view.

74.57

63.48

SCALE 1 : 10

DETAIL

The mounting access for bar

catch and safety must be to inside

of rack as shown.

Note: Titan G2 Series will not have an

upright wrap as shown

Step one

Attach bar holders to ends of each base as shown.

Depending on the build of your rack the bar holder

number may vary. (Max two per side)

Before Assembling this rack:

Consider how much space will be

required around the unit to access weights

and not interfere with other equipment.

Step Two

Attach storage post and front upright to right

base as shown. Repeat for left side.

Note: The base mounting flanges must face outward

All parts have a part number.

Position the part number to be

covered by its mating component

or up as shown in this view.

74.57

63.48

SCALE 1 : 10

DETAIL

The mounting access for bar

catch and safety must be to inside

of rack as shown.

Note: Titan G2 Series will not have an

upright wrap as shown

Step one

Attach bar holders to ends of each base as shown.

Depending on the build of your rack the bar holder

number may vary. (Max two per side)

Before Assembling this rack:

Consider how much space will be

required around the unit to access weights

and not interfere with other equipment.

Step Two

Attach storage post and front upright to right

base as shown. Repeat for left side.

Note: The base mounting flanges must face outward

All parts have a part number.

Position the part number

to be covered by its mating

component or up as shown

in this view.

Before assembling this rack:

Consider how much space will be

required around the unit to access weights

and not interfere with other equipment.

The mounting access for bar

catch and safety must be to inside

of rack as shown.

Note: Titan G2 Series will not have an

upright wrap as shown

Step 2

Attach storage post and front upright to right

base as shown. Repeat for left side.

Note: The base mounting anges must face outward

Step 1

Attach bar holders to ends of each base as shown.

Depending on the build of your rack the bar holder

number may vary. (Max two per side)

Step Four

Attach right half to left half as shown using

horizontal base .

Note: The carriage bolt heads should be on the outside of the rack

Install carriage bolt heads

as shown with all bolt heads

facing the front of the rack

Step Three

Attach horizontal cross member to

storage post and front upright to right

base as shown. Repeat for left side.

Install carriage bolt

heads as shown with

all bolt heads facing the

front of the rack

Step 3 A

Attach horizontal cross member to

storage post and front 8’ upright to right

base as shown. Repeat for left side.

Install carriage bolt heads

as shown with all bolt heads

facing the front of the rack

Step 3 B

Attach horizontal cross member to

storage post and front 9’ upright to right

base as shown. Repeat for left side.

DETAIL A

SCALE 1:6

DETAIL A

SCALE 1:6

Step Five

Attach horizontal chinup bar between left and

right uprights as shown. This bar may vary

based on your model

Note :This step requires two people to lift and fasten.

Use 5" bolt on ULTRA PRO

Use 4" bolt on TITAN G2

Step Six

Mount weight pegs in desired locations.

The recommended

spacing between each peg is (4) holes as

shown.

Additional band/belt storage

included on some models

Step 5 A

Attach horizontal chin up bar between left and

right 8’ uprights as shown. This bar may vary

based on your model.

Note: This step requires two people to lift and fasten.

Use 5” bolt on ULTRA PRO™

Use 4” bolt on TITAN G2

Step Four

Attach right half to left half as shown using

horizontal base .

Note:

The carriage bolt heads should be on the outside of the rack

Install carriage bolt heads

as shown with all bolt heads

facing the front of the rack

Step Three

Attach horizontal cross member to

storage post and front upright to right

base as shown. Repeat for left side.

Step 4

Attach right half to left half as shown using

horizontal base.

Note: The carriage bolt heads should be on the outside of the rack.

Step Five

Attach horizontal chinup bar between left and

right uprights as shown. This bar may vary

based on your model

Note :This step requires two people to lift and fasten.

Use 5" bolt on ULTRA PRO

Use 4" bolt on TITAN G2

Step Six

Mount weight pegs in desired locations.

The recommended

spacing between each peg is (4) holes as

shown.

Additional band/belt storage

included on some models

Additional band/belt storage

included on some models

Step 5 B

Attach horizontal chin up bar between left and

right 9’ uprights as shown. This bar may vary

based on your model.

Note: This step requires two people to lift and fasten.

Step 6

Mount weight pegs in desired locations.

The recommended spacing between each

peg is (4) holes as shown.

Step Seven

Mount bar catch and safety assemblies

to rack at desired location.

Step Eight

Position rack in final position and anchor to

floor using available holes on each base

Step Seven

Mount bar catch and safety assemblies

to rack at desired location.

Step Eight

Position rack in final position and anchor to

floor using available holes on each base

Step 7

Mount bar catch and safety assemblies

to rack at desired location.

Step 8

Position rack in nal position and anchor to

oor using available holes on each base.

Mount with 1/2” oor anchors at all four corners using holes

provided. (Anchors not provided)

Step Nine

Tighten each hardware connection.

The end of each bolt should extend beyond nylock

nut face as shown

Maintenance

Preventative actions will keep

your facility safe and productive

for all users

1) Wipe Down Equipment

Use general purpose cleaner.

Avoid Bleach based solutions

2) Lubricate all Moving parts

Use a silcone spray and clean

rag to apply

3) Tighten all hardware

Inspect the condition of all

hardware and tighten loose

fasteners

4)Inspect wear guards

To prevent metal to metal

contact with components keep

wear surfaces protected.

5)Replace all worn parts

End of bolt MUST

extend beyond nut face

at all locations

Step 9

Tighten each hardware connection.

The end of each bolt should extend beyond nylock nut

face as shown.

End of bolt MUST

extend beyond nut face

at all locations

Maintenance

Preventative actions will keep your

facility safe and productive for all

users

1) Wipe Down Equipment

Use gneral purpose cleaner.

Avoid Bleach based solutions.

2) Lubricate All Moving Parts

Use a silicone spray and clean

rag to apply.

3) Tighten All Hardware

Inspect the condition of all

hardware and tighten loose

fasteners.

4) Inspect Wear Guards

To prevent metal to metal

contact with components keep

wear surfaces protected.

5) Replace All Worn Parts

HARDWARE PACK CONTENTS

*QUANTITIES VARY BY MODEL*

HALF RACK

INSTRUCTION SHEET

.59

LKNT-500-002

1.50

.53

FLW-500-001

CAIR-500-002

.50

5.00

CAIR-500-001

.50

4.00

Models:

400512

TITAN PRO HALF RACK ASSEMBLY INSTRUCTIONS

844-678-7447 www.MyDynamicFitness.com

Tools Required:

(2) 1/2” Hex Key Wrench

(2) 1/2" HEX KEY WRENCH

400512

Model:

Tools Required:

For installation and assembly questions please contact

DYNAMIC technical services at 844-678-7447

See the complete line of products at MYDYNAMICFITNESS.COM

Twitter@DynamicFandS

Facebook@DynamicfitnessandStrength

Instagram@Dynamic_fitness_and_strength

SINGLE BOLT

FLANGE FACING

UPWARDS

NUMBERED

UPRIGHT FACING

INWARD

NUMBERED

UPRIGHT FACING

INWARD

STEP TWO:

TAKE (2) SIDE FRAMES FROM STEP ONE, MAKING SURE THAT BOTH

NUMBERED SIDES ARE FACING INWWARD, AND JOIN TOGETHER USING

(2) 43" CONNECTORS. CONNECT USING THE LOWEST POSSIBLE HOLES

ON THE REAR NON NUMBERED UPRIGHT, AND THE HIGHEST 2 POSSIBLE

HOLES ON THE NUMBERED UPRIGHTS.

STEP ONE:

INSTALL THE UPRIGHT WITH LASER CUT NUMBERS, AND REAR NON

NUMBERED UPRIGHT TOGETHER USING THE SHOWN 24" CONNECTORS.

THE LOWER 24" CONNECTOR WILL HAVE 2 BOLT FLANGES ON BOTH ENDS,

AND THE UPPER CONNECTOR WILL HAVE A SINGLE BOLT FLANGE ON ONE

END. THE SINGLE BOLT FLANGE WILL CONNECT TO THE NUMBERED

UPRIGHTS WITH THE FLANGE FACING UPWARDS AS SHOWN.

REPEAT STEP TO CREATE (2) SIDE FRAMES.

CUSTOMER SERVICE: 844-678-7447

WWW.MYDYNAMICFITNESS.COM

Single Bolt Flange

Facing Upwards

Numbered upright

facing inward

Step 1

Install the upright with laser cut number, and rear

non numbered upright together using the shown

24” connectors. The lower 24” connector will

have 2 bolt anges on both ends, and the upper

connector will have a single bolt ange on one end.

The single bolt ange will connect to the numbered

uprights with the ange facing upwards as shown.

Repeat step to create 2 side frames.

SINGLE BOLT

FLANGE FACING

UPWARDS

NUMBERED

UPRIGHT FACING

INWARD

NUMBERED

UPRIGHT FACING

INWARD

STEP TWO:

TAKE (2) SIDE FRAMES FROM STEP ONE, MAKING SURE THAT BOTH

NUMBERED SIDES ARE FACING INWWARD, AND JOIN TOGETHER USING

(2) 43" CONNECTORS. CONNECT USING THE LOWEST POSSIBLE HOLES

ON THE REAR NON NUMBERED UPRIGHT, AND THE HIGHEST 2 POSSIBLE

HOLES ON THE NUMBERED UPRIGHTS.

STEP ONE:

INSTALL THE UPRIGHT WITH LASER CUT NUMBERS, AND REAR NON

NUMBERED UPRIGHT TOGETHER USING THE SHOWN 24" CONNECTORS.

THE LOWER 24" CONNECTOR WILL HAVE 2 BOLT FLANGES ON BOTH ENDS,

AND THE UPPER CONNECTOR WILL HAVE A SINGLE BOLT FLANGE ON ONE

END. THE SINGLE BOLT FLANGE WILL CONNECT TO THE NUMBERED

UPRIGHTS WITH THE FLANGE FACING UPWARDS AS SHOWN.

REPEAT STEP TO CREATE (2) SIDE FRAMES.

CUSTOMER SERVICE: 844-678-7447

WWW.MYDYNAMICFITNESS.COM

Step 2

Take 2 side frames from step one, making sure

that both numbered sides are facing inward, and

join together using 2-43” connectors. Connect

using the lowest possible holes on the rear non

numbered upright, and the highest 2 possible holes

on the numbered uprights.

Numbered upright

facing inward

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dynamic Fitnessgeräte Handbücher

Dynamic

Dynamic 301000 Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung