Dynojet Power commander V Bedienungsanleitung

11-014 www.powercommander.com 2013 Arctic Cat 700cc H1 ATV - PCV - 1

PARTS LIST

1 Power Commander

1 USB Cable

1 Installation Guide

2 Power Commander Decals

2 Dynojet Decals

1 Posi-tap

2 Velcro strips

1 Alcohol swab

THE LATEST POWER COMMANDER

SOFTWARE AND MAP FILES CAN BE

DOWNLOADED FROM OUR WEB SITE AT:

www.powercommander.com

2013 Arctic Cat 700cc H1 ATV

Installation Instructions

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

THE IGNITION MUST BE TURNED

OFF BEFORE INSTALLATION!

2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

11-014 www.powercommander.com 2013 Arctic Cat 700cc H1 ATV - PCV - 2

EXPANSION PORTS 1 & 2

Optional Accessories such as

POD-300 unit or Auto-tune kit

POWER COMMANDER V

INPUT ACCESSORY GUIDE

ACCESSORY INPUTS

Wire connections:

To input wires into the PCV first remove the rubber

plug on the backside of the unit and loosen the

screw for the corresponding input. Using a 22-24

gauge wire strip about 10mm from its end. Push the

wire into the hole of the PCV until is stops and then

tighten the screw. Make sure to reinstall the rubber

plug.

NOTE: If you tin the wires with solder it will make

inserting them easier.

USB CONNECTION

Map - (Input 1 or 2) The PCV has the ability to hold

2 different base maps. You can switch on the

fly between these two base maps when you

hook up a switch to the MAP inputs. You can

use any open/close type switch. The polarity

of the wires is not important. When using the

Autotune kit one position will hold a base map

and the other position will let you activate the

learning mode. When the switch is “CLOSED”

Autotune will be activated. (Set to Switch

Input #1 by default.)

Shifter- (Input 1 or 2) These inputs are for use with the

Dynojet quickshifter. Insert the wires from the

Dynojet quickshifter into the SHIFTER inputs.

The polarity of the wires is not important. (Set

to Switch Input #2 by default.)

Speed- If your application has a speed sensor then

you can tap into the signal side of the sensor

and run a wire into this input. This will allow

you to calculate gear position in the Control

Center Software. Once gear position is setup

you can alter your map based on gear position

and setup gear dependent kill times when

using a quickshifter.

Analog- This input is for a 0-5v signal such as

engine temp, boost, etc. Once this input

is established you can alter your fuel curve

based on this input in the control center

software.

Crank- Do NOT connect anything to this port unless

instructed to do so by Dynojet. It is used to

transfer crank trigger data from one module to

another.

ACCESSORY INPUTS

CRANK

ANALOG

SPEED

INPUT 1 (Grnd)

INPUT 1

INPUT 2 (Grnd)

INPUT 2

11-014 www.powercommander.com 2013 Arctic Cat 700cc H1 ATV - PCV - 3

1 Remove the seat and left hand side panel shown in Figure A.

2 Remove the storage cover shown in Figure B and the storage bin.

3 Loosen the clamp from the throttle body and remove the air snorkel from the

throttle body.

4 To make the fuel injector more accessible, lift the snorkel/airbox upward away

from the top of the engine.

5 Remove the two screws securing the tool kit to expose the battery.

6 Using the supplied Velcro, secure the PCV under the seat at the location

shown in Figure C.

Clean both surfaces with the supplied alcohol swab before attaching the

Velcro.

7 Route the PCV wiring harness under the frame spar toward the front of the

machine.

8 Attach the ground wire from the PCV to the negative (-) terminal of the battery.

FIG.A

FIG.B

Remove

FIG.C

Ground

Snorkel

PCV

Remove

11-014 www.powercommander.com 2013 Arctic Cat 700cc H1 ATV - PCV - 4

9 Disconnect the stock wiring harness from the fuel injector (Fig. D).

10 Plug the PCV wiring harness in-line of the fuel injector and the stock wiring

harness.

11 Locate the Throttle Position Sensor (TPS) on the

left hand side of the throttle body.

12 Using the supplied posi-tap, attach the GREY wire

from the PCV to the stock GREEN/BLACK wire

from the TPS.

13 Replace the storage bin, cover, tool kit, side panel,

and seat.

FIG.E

TPS

Posi-tap

FIG.D

Unplug

Andere Handbücher für Power commander V

Andere Dynojet Autozubehör Handbücher

Dynojet

Dynojet Power Commander III Service-Handbuch

Dynojet

Dynojet POWER VISION PV3-16-07 Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet POWER VISION PV3-2511C Bedienungsanleitung

Dynojet

Dynojet Power Commander III Bedienungsanleitung

Dynojet

Dynojet Power Commander III Bedienungsanleitung

Dynojet

Dynojet Power Commander FC Bedienungsanleitung

Dynojet

Dynojet POWER VISION PV3-17-02 Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet POWER VISION PV3-25-09 Bedienungsanleitung

Dynojet

Dynojet 24xLC2 Linx Bedienungsanleitung

Dynojet

Dynojet INVISION INV-1901 Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet power commander III Bedienungsanleitung

Dynojet

Dynojet power commander III Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet power commander III Bedienungsanleitung

Dynojet

Dynojet Auto Tune Bedienungsanleitung

Dynojet

Dynojet POWER VISION 3 Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung